Switch version incrementing to the command put together by @noroadsleft. (#6310 )

* Switch version incrementing to the command put together by @noroadsleft. * Update util/travis_compiled_push.sh Co-Authored-By: noroadsleft <[email protected]>
[Keyboard] Adding KeyHive Maypad (#6287 )
2019-07-11 22:33:25 -07:00 · 2019-07-11 13:01:17 -07:00 · 2019-07-11 12:27:13 -07:00 · 2019-07-11 12:09:48 -07:00 · 2019-07-11 12:05:13 -07:00 · 2019-07-11 12:04:22 -07:00
55 changed files with 1752 additions and 122 deletions
@@ -1,28 +1,44 @@
 # Unicode Support
-There are three Unicode keymap definition methods available in QMK:
+Unicode characters can be input straight from your keyboard! There are some limitations, however.
-## `UNICODE_ENABLE`
+QMK has three different methods for enabling Unicode input and defining keycodes:
-Supports Unicode up to `0x7FFF`. This covers characters for most modern languages, as well as symbols, but it doesn't cover emoji. The keycode function is `UC(c)` in the keymap, where _c_ is the code point's number (preferably hexadecimal, up to 4 digits long). For example: `UC(0x45B)`, `UC(0x30C4)`.
+## Basic Unicode
-## `UNICODEMAP_ENABLE`
+This method supports Unicode code points up to `0x7FFF`. This covers characters for most modern languages, as well as symbols, but it doesn't cover emoji.
-Supports Unicode up to `0x10FFFF` (all possible code points). You need to maintain a separate mapping table `const uint32_t PROGMEM unicode_map[] = {...}` in your keymap file. The keycode function is `X(i)`, where _i_ is an array index into the mapping table. The table may contain at most 16384 entries.
+Add the following to your `rules.mk`:
-You may want to have an enum to make referencing easier. So, you could add something like this to your keymap file:
+```make
 UNICODE_ENABLE = yes
 ```
 Then add `UC(c)` keycodes to your keymap, where _c_ is the code point (preferably in hexadecimal, up to 4 digits long). For example: `UC(0x45B)`, `UC(0x30C4)`.
 ## Unicode Map
 This method supports all possible code points (up to `0x10FFFF`); however, you need to maintain a separate mapping table in your keymap file, which may contain at most 16384 entries.
 Add the following to your `rules.mk`:
 ```make
 UNICODEMAP_ENABLE = yes
 ```
 Then add `X(i)` keycodes to your keymap, where _i_ is an array index into the mapping table:
 ```c
 enum unicode_names {
-  BANG,
+    BANG,
-  IRONY,
+    IRONY,
-  SNEK,
+    SNEK
 };
 const uint32_t PROGMEM unicode_map[] = {
-  [BANG]  = 0x203D,  // ‽
+    [BANG]  = 0x203D,  // ‽
-  [IRONY] = 0x2E2E,  // ⸮
+    [IRONY] = 0x2E2E,  // ⸮
-  [SNEK]  = 0x1F40D, // 🐍
+    [SNEK]  = 0x1F40D, // 🐍
 };
 ```
@@ -30,27 +46,33 @@ Then you can use `X(BANG)`, `X(SNEK)` etc. in your keymap.
 ### Lower and Upper Case
-Characters often come in lower and upper case pairs, for example: å, Å. To make inputting these characters easier, you can use `XP(i, j)` in your keymap, where _i_ and _j_ are the mapping table indices of the lower and upper case character, respectively. If you're holding down Shift or have Caps Lock turned on when you press the key, the second (upper case) character will be inserted; otherwise, the first (lower case) version will appear.
+Characters often come in lower and upper case pairs, such as å and Å. To make inputting these characters easier, you can use `XP(i, j)` in your keymap, where _i_ and _j_ are the mapping table indices of the lower and upper case character, respectively. If you're holding down Shift or have Caps Lock turned on when you press the key, the second (upper case) character will be inserted; otherwise, the first (lower case) version will appear.
-This is most useful when creating a keymap for an international layout with special characters. Instead of having to put the lower and upper case versions of a character on separate keys, you can have them both on the same key by using `XP`. This blends Unicode keys in with regular alphas.
+This is most useful when creating a keymap for an international layout with special characters. Instead of having to put the lower and upper case versions of a character on separate keys, you can have them both on the same key by using `XP()`. This helps blend Unicode keys in with regular alphas.
 Due to keycode size constraints, _i_ and _j_ can each only refer to one of the first 128 characters in your `unicode_map`. In other words, 0 ≤ _i_ ≤ 127 and 0 ≤ _j_ ≤ 127. This is enough for most use cases, but if you'd like to customize the index calculation, you can override the [`unicodemap_index()`](https://github.com/qmk/qmk_firmware/blob/71f640d47ee12c862c798e1f56392853c7b1c1a8/quantum/process_keycode/process_unicodemap.c#L40) function. This also allows you to, say, check Ctrl instead of Shift/Caps.
-## `UCIS_ENABLE`
+## UCIS
-Supports Unicode up to `0x10FFFF` (all possible code points). As with `UNICODEMAP`, you need to maintain a mapping table in your keymap file. However, there are no built-in keycodes for this feature — you have to add a keycode or function that calls `qk_ucis_start()`. Once this function has been called, you can type the corresponding mnemonic for your character, then hit Space or Enter to complete it, or Esc to cancel. If the mnemonic matches an entry in your table, the typed text will automatically be erased and the corresponding Unicode character inserted.
+This method also supports all possible code points. As with the Unicode Map method, you need to maintain a mapping table in your keymap file. However, there are no built-in keycodes for this feature — you have to create a custom keycode or function that invokes this functionality.
-For instance, you could define a table like this in your keymap file:
+Add the following to your `rules.mk`:
 ```make
 UCIS_ENABLE = yes
 ```
 Then define a table like this in your keymap file:
 ```c
 const qk_ucis_symbol_t ucis_symbol_table[] = UCIS_TABLE(
-  UCIS_SYM("poop", 0x1F4A9), // 💩
+    UCIS_SYM("poop", 0x1F4A9), // 💩
-  UCIS_SYM("rofl", 0x1F923), // 🤣
+    UCIS_SYM("rofl", 0x1F923), // 🤣
-  UCIS_SYM("kiss", 0x1F619)  // 😙
+    UCIS_SYM("kiss", 0x1F619)  // 😙
 );
 ```
-To use it, call `qk_ucis_start()`, then type "rofl" and hit Enter. QMK should erase the "rofl" text and insert the laughing emoji.
+To use it, call `qk_ucis_start()`. Then, type the mnemonic for the character (such as "rofl"), and hit Space or Enter. QMK should erase the "rofl" text and insert the laughing emoji.
 ### Customization
@@ -68,7 +90,7 @@ Unicode input in QMK works by inputting a sequence of characters to the OS, sort
 The following input modes are available:
-* **`UC_OSX`**: macOS built-in Unicode hex input. Supports code points up to `0xFFFF` (`0x10FFFF` with `UNICODEMAP`).
+* **`UC_OSX`**: macOS built-in Unicode hex input. Supports code points up to `0xFFFF` (`0x10FFFF` with Unicode Map).
  To enable, go to _System Preferences > Keyboard > Input Sources_, add _Unicode Hex Input_ to the list (it's under _Other_), then activate it from the input dropdown in the Menu Bar.
  By default, this mode uses the left Option key (`KC_LALT`) for Unicode input, but this can be changed by defining [`UNICODE_KEY_OSX`](#input-key-configuration) with another keycode.
@@ -112,7 +134,7 @@ You can also switch the input mode by calling `set_unicode_input_mode(x)` in you
 ```c
 void eeconfig_init_user(void) {
-  set_unicode_input_mode(UC_LNX);
+    set_unicode_input_mode(UC_LNX);
 }
 ```
@@ -1,5 +1,4 @@
-#ifndef CONFIG_H
+#pragma once
 #define CONFIG_H
 #include "config_common.h"
@@ -9,40 +8,225 @@
 #define DEVICE_VER      0x0001
 #define MANUFACTURER    Unikeyboard
 #define PRODUCT         Felix
-#define DESCRIPTION     4x5 number/macropad.
+#define DESCRIPTION     4x5 number/macropad
 /* key matrix size */
 #define MATRIX_ROWS 5
 #define MATRIX_COLS 4
-/* key matrix pins */
+/*
 * Keyboard Matrix Assignments
 *
 * Change this to how you wired your keyboard
 * COLS: AVR pins used for columns, left to right
 * ROWS: AVR pins used for rows, top to bottom
 * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
 *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
 *
 */
 #define MATRIX_ROW_PINS { B2, B3, B1, F7, F6 }
 #define MATRIX_COL_PINS { B5, B4, E6, D7 }
 #define UNUSED_PINS
-/* COL2ROW or ROW2COL */
+/* COL2ROW, ROW2COL */
 #define DIODE_DIRECTION ROW2COL
-/* number of backlight levels */
+/*
-/* Not sure what pin controls the backlighting, need help for this. */
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
-#define BACKLIGHT_PIN
+ */
-#define BACKLIGHT_LEVELS 5
+#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
-/* Set 0 if debouncing isn't needed */
+#define BACKLIGHT_PIN C6
 #define BACKLIGHT_LEVELS 5
 //#define BACKLIGHT_BREATHING
 // #define RGB_DI_PIN E2
 // #ifdef RGB_DI_PIN
 //   #define RGBLED_NUM 16
 //   #define RGBLIGHT_HUE_STEP 8
 //   #define RGBLIGHT_SAT_STEP 8
 //   #define RGBLIGHT_VAL_STEP 8
 //   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
 //   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
 // /*== all animations enable ==*/
 //   #define RGBLIGHT_ANIMATIONS
 // /*== or choose animations ==*/
 //   #define RGBLIGHT_EFFECT_BREATHING
 //   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
 //   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
 //   #define RGBLIGHT_EFFECT_SNAKE
 //   #define RGBLIGHT_EFFECT_KNIGHT
 //   #define RGBLIGHT_EFFECT_CHRISTMAS
 //   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
 //   #define RGBLIGHT_EFFECT_RGB_TEST
 //   #define RGBLIGHT_EFFECT_ALTERNATING
 // /*== customize breathing effect ==*/
 //   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
 //   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
 //   /*==== use exp() and sin() ====*/
 //   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
 //   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
 // #endif
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 /* define if matrix has ghost (lacks anti-ghosting diodes) */
 //#define MATRIX_HAS_GHOST
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
-/* there is no rgb underglow by default. */
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
-#define RGB_DI_PIN
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
-#define RGBLIGHT_ANIMATIONS
+ */
-#define RGBLED_NUM 16
+// #define GRAVE_ESC_CTRL_OVERRIDE
 #define RGBLIGHT_HUE_STEP 8
 #define RGBLIGHT_SAT_STEP 8
 #define RGBLIGHT_VAL_STEP 8
 /*
 * Force NKRO
 *
 * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
 * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
 * makefile for this to work.)
 *
 * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
 * until the next keyboard reset.
 *
 * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
 * fully operational during normal computer usage.
 *
 * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
 * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
 * bootmagic, NKRO mode will always be enabled until it is toggled again during a
 * power-up.
 *
 */
 //#define FORCE_NKRO
 /*
 * Magic Key Options
 *
 * Magic keys are hotkey commands that allow control over firmware functions of
 * the keyboard. They are best used in combination with the HID Listen program,
 * found here: https://www.pjrc.com/teensy/hid_listen.html
 *
 * The options below allow the magic key functionality to be changed. This is
 * useful if your keyboard/keypad is missing keys and you want magic key support.
 *
 */
 /* key combination for magic key command */
 /* defined by default; to change, uncomment and set to the combination you want */
 // #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
 /* control how magic key switches layers */
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
 /* override magic key keymap */
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
 //#define MAGIC_KEY_HELP           H
 //#define MAGIC_KEY_HELP_ALT       SLASH
 //#define MAGIC_KEY_DEBUG          D
 //#define MAGIC_KEY_DEBUG_MATRIX   X
 //#define MAGIC_KEY_DEBUG_KBD      K
 //#define MAGIC_KEY_DEBUG_MOUSE    M
 //#define MAGIC_KEY_VERSION        V
 //#define MAGIC_KEY_STATUS         S
 //#define MAGIC_KEY_CONSOLE        C
 //#define MAGIC_KEY_LAYER0         0
 //#define MAGIC_KEY_LAYER0_ALT     GRAVE
 //#define MAGIC_KEY_LAYER1         1
 //#define MAGIC_KEY_LAYER2         2
 //#define MAGIC_KEY_LAYER3         3
 //#define MAGIC_KEY_LAYER4         4
 //#define MAGIC_KEY_LAYER5         5
 //#define MAGIC_KEY_LAYER6         6
 //#define MAGIC_KEY_LAYER7         7
 //#define MAGIC_KEY_LAYER8         8
 //#define MAGIC_KEY_LAYER9         9
 //#define MAGIC_KEY_BOOTLOADER     B
 //#define MAGIC_KEY_BOOTLOADER_ALT ESC
 //#define MAGIC_KEY_LOCK           CAPS
 //#define MAGIC_KEY_EEPROM         E
 //#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
 //#define MAGIC_KEY_NKRO           N
 //#define MAGIC_KEY_SLEEP_LED      Z
 /*
 * Feature disable options
 *  These options are also useful to firmware size reduction.
 */
 /* disable debug print */
 //#define NO_DEBUG
 /* disable print */
 //#define NO_PRINT
 /* disable action features */
 //#define NO_ACTION_LAYER
 //#define NO_ACTION_TAPPING
 //#define NO_ACTION_ONESHOT
 //#define NO_ACTION_MACRO
 //#define NO_ACTION_FUNCTION
 /*
 * MIDI options
 */
 /* Prevent use of disabled MIDI features in the keymap */
 //#define MIDI_ENABLE_STRICT 1
 /* enable basic MIDI features:
   - MIDI notes can be sent when in Music mode is on
 */
 //#define MIDI_BASIC
 /* enable advanced MIDI features:
   - MIDI notes can be added to the keymap
   - Octave shift and transpose
   - Virtual sustain, portamento, and modulation wheel
   - etc.
 */
 //#define MIDI_ADVANCED
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -1,5 +1,4 @@
-#ifndef FELIX_H
+#pragma once
 #define FELIX_H
 #include "quantum.h"
@@ -18,5 +17,3 @@
 }
 #define LAYOUT LAYOUT_ortho_5x4
 #endif
@@ -6,7 +6,28 @@
  "height": 5,
  "layouts": {
    "LAYOUT_ortho_5x4": {
-      "layout": [{"label":"K000", "x":0, "y":0}, {"label":"K001", "x":1, "y":0}, {"label":"K002", "x":2, "y":0}, {"label":"K003", "x":3, "y":0}, {"label":"K100", "x":0, "y":1}, {"label":"K101", "x":1, "y":1}, {"label":"K102", "x":2, "y":1}, {"label":"K103", "x":3, "y":1}, {"label":"K200", "x":0, "y":2}, {"label":"K201", "x":1, "y":2}, {"label":"K202", "x":2, "y":2}, {"label":"K203", "x":3, "y":2}, {"label":"K300", "x":0, "y":3}, {"label":"K301", "x":1, "y":3}, {"label":"K302", "x":2, "y":3}, {"label":"K303", "x":3, "y":3}, {"label":"K400", "x":0, "y":4}, {"label":"K401", "x":1, "y":4}, {"label":"K402", "x":2, "y":4}, {"label":"K403", "x":3, "y":4}]
+      "layout": [
        {"label":"K000", "x":0, "y":0},
        {"label":"K001", "x":1, "y":0},
        {"label":"K002", "x":2, "y":0},
        {"label":"K003", "x":3, "y":0},
        {"label":"K100", "x":0, "y":1},
        {"label":"K101", "x":1, "y":1},
        {"label":"K102", "x":2, "y":1},
        {"label":"K103", "x":3, "y":1},
        {"label":"K200", "x":0, "y":2},
        {"label":"K201", "x":1, "y":2},
        {"label":"K202", "x":2, "y":2},
        {"label":"K203", "x":3, "y":2},
        {"label":"K300", "x":0, "y":3},
        {"label":"K301", "x":1, "y":3},
        {"label":"K302", "x":2, "y":3},
        {"label":"K303", "x":3, "y":3},
        {"label":"K400", "x":0, "y":4},
        {"label":"K401", "x":1, "y":4},
        {"label":"K402", "x":2, "y":4},
        {"label":"K403", "x":3, "y":4}
      ]
    }
  }
 }
@@ -1,22 +1,11 @@
 #include QMK_KEYBOARD_H
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-
+    LAYOUT_ortho_5x4(
-  LAYOUT(
+        KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS,
-    KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS,
+        KC_P7,   KC_P8,   KC_P9,   KC_PPLS,
-    KC_P7,   KC_P8,   KC_P9,   KC_PPLS,
+        KC_P4,   KC_P5,   KC_P6,   KC_HOME,
-    KC_P4,   KC_P5,   KC_P6,   KC_HOME,
+        KC_P1,   KC_P2,   KC_P3,   KC_END,
-    KC_P1,   KC_P2,   KC_P3,   KC_END,
+        KC_P0,   KC_PEQL, KC_PDOT, KC_PENT
-    KC_P0,   KC_PEQL, KC_PDOT, KC_PENT
+    )
  ),
 };
 void persistant_default_layer_set(uint16_t default_layer) {
 }
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
  switch (keycode) {
  }
  return true;
 }
@@ -10,4 +10,4 @@ Make example for this keyboard (after setting up your build environment):
    make felix:default
-See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information.
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@@ -37,22 +37,34 @@ F_USB = $(F_CPU)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-# Boot Section Size in *bytes*
+# Bootloader selection
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+#   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
 #   atmega32a    bootloadHID
 BOOTLOADER = caterina
 # Build Options
-#   comment out to disable the options.
+#   change yes to no to disable
 #
-BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no	# Console for debug(+400)
+CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = no    # Commands for debug and configuration
+COMMAND_ENABLE = no         # Commands for debug and configuration
-SLEEP_LED_ENABLE = no  # Breathing sleep LED during USB suspend
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-NKRO_ENABLE = yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-BACKLIGHT_ENABLE = no  # Enable keyboard backlight functionality
+NKRO_ENABLE = yes           # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-AUDIO_ENABLE = no
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
-RGBLIGHT_ENABLE = no
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
 MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
 UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 LAYOUTS = ortho_5x4
@@ -76,3 +76,5 @@ SRC += ws2812.c
 SRC += rgbsps.c
 SRC += analog.c
 SRC += matrix.c
 LINK_TIME_OPTIMIZATION_ENABLE = yes
@@ -0,0 +1,14 @@
 # wulkan
 Handwired 40% keyboard build with Proton C.
 Keyboard Maintainer: [Napoleon Wulkan](https://github.com/wulkan)  
 Hardware Supported: Proton C  
 Hardware Availability: [OLKB.com](https://olkb.com)
 Make example for this keyboard (after setting up your build environment):
    make handwired/wulkan:default:dfu-util
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@@ -0,0 +1,23 @@
 #pragma once
 #include "config_common.h"
 /* USB Device descriptor parameter */
 #define VENDOR_ID       0xFEED
 #define PRODUCT_ID      0x6060
 #define DEVICE_VER      0x0001
 #define MANUFACTURER    Wulkan
 #define PRODUCT         Handwired48Keys
 #define DESCRIPTION     A compact ortholinear handwired keyboard
 /* key matrix size */
 #define MATRIX_ROWS 4
 #define MATRIX_COLS 12
 #define MATRIX_ROW_PINS { B8, A0, A1, A2 }
 #define MATRIX_COL_PINS { B13, B14, B15, B9, B7, B6, B5, B4, B3, B2, B1, B0 }
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 #define FORCE_NKRO
@@ -0,0 +1,13 @@
 {
    "keyboard_name": "wulkan",
    "url": "",
    "maintainer": "Napoleon Wulkan",
    "width": 12,
    "height": 4,
    "layouts": {
      "LAYOUT_ortho_4x12": {
        "key_count": 48,
        "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":0, "y":1}, {"x":1, "y":1}, {"x":2, "y":1}, {"x":3, "y":1}, {"x":4, "y":1}, {"x":5, "y":1}, {"x":6, "y":1}, {"x":7, "y":1}, {"x":8, "y":1}, {"x":9, "y":1}, {"x":10, "y":1}, {"x":11, "y":1}, {"x":0, "y":2}, {"x":1, "y":2}, {"x":2, "y":2}, {"x":3, "y":2}, {"x":4, "y":2}, {"x":5, "y":2}, {"x":6, "y":2}, {"x":7, "y":2}, {"x":8, "y":2}, {"x":9, "y":2}, {"x":10, "y":2}, {"x":11, "y":2}, {"x":0, "y":3}, {"x":1, "y":3}, {"x":2, "y":3}, {"x":3, "y":3}, {"x":4, "y":3}, {"x":5, "y":3}, {"x":6, "y":3}, {"x":7, "y":3}, {"x":8, "y":3}, {"x":9, "y":3}, {"x":10, "y":3}, {"x":11, "y":3}]
      }
    }
  }
@@ -0,0 +1,111 @@
 #include QMK_KEYBOARD_H
 enum layers {
  _QWERTY,
  _LOWER,
  _RAISE,
  _ADJUST,
 };
 enum unicode_names {
  SE_AA_HIGH,
  SE_AE_HIGH,
  SE_OE_HIGH,
  SE_AA_LOW,
  SE_AE_LOW,
  SE_OE_LOW,
 };
 const uint32_t PROGMEM unicode_map[] = {
  [SE_AA_HIGH] = 0x00C5,
  [SE_AE_HIGH] = 0x00C4,
  [SE_OE_HIGH] = 0x00D6,
  [SE_AA_LOW]  = 0x00E5,
  [SE_AE_LOW]  = 0x00E4,
  [SE_OE_LOW]  = 0x00F6,
 };
 #define LOWER  MO(_LOWER)
 #define RAISE  MO(_RAISE)
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 /* Qwerty
 * ,-----------------------------------------------------------------------------------.
 * | Tab  |   Q  |   W  |   E  |   R  |   T  |   Y  |   U  |   I  |   O  |   P  | Bksp |
 * |------+------+------+------+------+-------------+------+------+------+------+------|
 * | Esc  |   A  |   S  |   D  |   F  |   G  |   H  |   J  |   K  |   L  |   ;  |  "   |
 * |------+------+------+------+------+------|------+------+------+------+------+------|
 * | Shift|   Z  |   X  |   C  |   V  |   B  |   N  |   M  |   ,  |   .  |   /  |Shift |
 * |------+------+------+------+------+------+------+------+------+------+------+------|
 * |      | Ctrl | Alt  | GUI  |Lower |Enter |Space |Raise | Left | Down |  Up  |Right |
 * `-----------------------------------------------------------------------------------'
 */
 [_QWERTY] = LAYOUT_ortho_4x12(
  KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC,
  KC_ESC,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,
  KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,
  _______, KC_LCTL, KC_LALT, KC_LGUI, LOWER,   KC_ENT,  KC_SPC,  RAISE,   KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT
 ),
 /* Lower
 * ,-----------------------------------------------------------------------------------.
 * |   ~  |   !  |   @  |   #  |   $  |   %  |   ^  |   &  |   *  |   (  |   )  | Bksp |
 * |------+------+------+------+------+-------------+------+------+------+------+------|
 * | Del  |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |   _  |   +  |   {  |   }  |  |   |
 * |------+------+------+------+------+------|------+------+------+------+------+------|
 * |      |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |ISO ~ |ISO | |      |      |      |
 * |------+------+------+------+------+------+------+------+------+------+------+------|
 * |      |      |      |      |      |      |      |      | Next | Vol- | Vol+ | Play |
 * `-----------------------------------------------------------------------------------'
 */
 [_LOWER] = LAYOUT_ortho_4x12(
  KC_TILD, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR,    KC_ASTR,    KC_LPRN, KC_RPRN, KC_BSPC,
  KC_DEL,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_UNDS,    KC_PLUS,    KC_LCBR, KC_RCBR, KC_PIPE,
  _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  S(KC_NUHS), S(KC_NUBS), _______, _______, _______,
  _______, _______, _______, _______, _______, _______, _______, _______,    KC_MNXT,    KC_VOLD, KC_VOLU, KC_MPLY
 ),
 /* Raise
 * ,-----------------------------------------------------------------------------------.
 * |   `  |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   0  |  Del |
 * |------+------+------+------+------+-------------+------+------+------+------+------|
 * | Del  |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |   -  |   =  |   [  |   ]  |  \   |
 * |------+------+------+------+------+------|------+------+------+------+------+------|
 * |      |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |ISO # |ISO / |      |      |      |
 * |------+------+------+------+------+------+------+------+------+------+------+------|
 * |      |      |      |      |      |      |      |      | Next | Vol- | Vol+ | Play |
 * `-----------------------------------------------------------------------------------'
 */
 [_RAISE] = LAYOUT_ortho_4x12(
  KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_DEL,
  KC_DEL,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_BSLS,
  _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_NUHS, KC_NUBS, _______, _______, _______,
  _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY
 ),
 /* Adjust (Lower + Raise)
 * ,-----------------------------------------------------------------------------------.
 * |      | Reset|      |      |      |      |      |      |      |      |   Å  |  Del |
 * |------+------+------+------+------+-------------+------+------+------+------+------|
 * |      |      |      |      |      |      |      |      |      |   Ö  |   Ä  |      |
 * |------+------+------+------+------+------|------+------+------+------+------+------|
 * |      |      |      |      |      |      |      |      |      |      |      |      |
 * |------+------+------+------+------+------+------+------+------+------+------+------|
 * |      |      |      |      |      |      |      |      |      |      |      |      |
 * `-----------------------------------------------------------------------------------'
 */
 [_ADJUST] = LAYOUT_ortho_4x12(
  _______, RESET,   _______, _______, KC_WH_U, _______, _______, KC_MS_U, _______, _______,                   XP(SE_AA_LOW, SE_AA_HIGH), KC_DEL,
  _______, _______, _______, _______, KC_WH_D, _______, KC_MS_L, KC_MS_D, KC_MS_R, XP(SE_OE_LOW, SE_OE_HIGH), XP(SE_AE_LOW, SE_AE_HIGH), _______,
  _______, KC_ACL0, KC_ACL1, KC_ACL2, _______, _______, KC_BTN1, _______, KC_BTN2, _______,                   _______,                   _______,
  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,                   _______,                   _______
 )
 };
 uint32_t layer_state_set_user(uint32_t state) {
  return update_tri_layer_state(state, _LOWER, _RAISE, _ADJUST);
 }
 void eeconfig_init_user(void) {
  set_unicode_input_mode(UC_LNX);
 }
@@ -0,0 +1 @@
 UNICODEMAP_ENABLE = yes
@@ -0,0 +1,22 @@
 MCU = STM32F303
 # Build Options
 #   comment out to disable the options.
 #
 BACKLIGHT_ENABLE = no
 BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration
 MOUSEKEY_ENABLE = yes       # Mouse keys
 EXTRAKEY_ENABLE = yes       # Audio control and System control
 CONSOLE_ENABLE = no         # Console for debug
 COMMAND_ENABLE = no         # Commands for debug and configuration
 NKRO_ENABLE = yes           # USB Nkey Rollover
 AUDIO_ENABLE = no
 RGBLIGHT_ENABLE = no
 LAYOUTS = ortho_4x12
 MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
 UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 NO_SUSPEND_POWER_DOWN = yes
 UNICODEMAP_ENABLE = no
@@ -0,0 +1,6 @@
 #include "wulkan.h"
 void matrix_init_kb(void) {
  matrix_init_user();
 }
@@ -0,0 +1,21 @@
 #pragma once
 #include "quantum.h"
 #define ___ KC_NO
 #define LAYOUT_ortho_4x12( \
    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \
    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \
    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \
    K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B  \
 ) \
 { \
    { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \
    { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \
    { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \
    { K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B }  \
 }
 #define LAYOUT LAYOUT_ortho_4x12
@@ -0,0 +1,19 @@
 #pragma once
 #define FORCE_NKRO
 #define MOUSEKEY_DELAY             50
 #define MOUSEKEY_INTERVAL          15
 #define MOUSEKEY_MAX_SPEED         4
 #define MOUSEKEY_TIME_TO_MAX       50
 #define MOUSEKEY_WHEEL_MAX_SPEED   1
 #define MOUSEKEY_WHEEL_TIME_TO_MAX 50
 #define NO_ACTION_FUNCTION
 #define NO_ACTION_MACRO
 #define NO_ACTION_ONESHOT
 #define PERMISSIVE_HOLD
 #define TAPPING_TERM        200
 #define TAPPING_TOGGLE      2
 #define TAP_HOLD_CAPS_DELAY 50
@@ -0,0 +1,79 @@
 #include QMK_KEYBOARD_H
 #define FN      MO(L_FN)
 #define FN_CAPS LT(L_FN, KC_CAPS)
 #define FN_ESC  LT(L_FN, KC_ESC)
 #define FN_FNLK TT(L_FN)
 #define MV_UP   LCTL(KC_UP)
 #define MV_DOWN LCTL(KC_DOWN)
 #define MV_LEFT LCTL(KC_LEFT)
 #define MV_RGHT LCTL(KC_RGHT)
 #define TOP     LCTL(KC_HOME)
 #define BOTTOM  LCTL(KC_END)
 enum keycodes {
    CLEAR = SAFE_RANGE,
 };
 enum layers {
    L_BASE,
    L_FN,
 };
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
    switch (keycode) {
    case CLEAR:
        if (record->event.pressed) {
            SEND_STRING(SS_LCTRL("a") SS_TAP(X_DELETE));
        }
        return false;
    default:
        return true;
    }
 }
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    /* Base layer
     * ┌───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┐
     * │ ` │ 1 │ 2 │ 3 │ 4 │ 5 │ 6 │ 7 │ 8 │ 9 │ 0 │ - │ = │ \ │ ` │PSc│
     * ├───┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴───┼───┤
     * │ Tab │ Q │ W │ E │ R │ T │ Y │ U │ I │ O │ P │ [ │ ] │Bspc │Del│
     * ├─────┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴─────┼───┤
     * │FnEsc │ A │ S │ D │ F │ G │ H │ J │ K │ L │ ; │ ' │ Enter  │PgU│
     * ├──────┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴────┬───┼───┤
     * │ LShift │ Z │ X │ C │ V │ B │ N │ M │ , │ . │ / │RShift│ ↑ │PgD│
     * ├────┬───┴┬──┴─┬─┴───┴───┴───┴───┴───┴──┬┴───┼───┴┬─┬───┼───┼───┤
     * │LCtl│LGui│LAlt│         Space          │RAlt│FnLk│ │ ← │ ↓ │ → │
     * └────┴────┴────┴────────────────────────┴────┴────┘ └───┴───┴───┘
     */
    [L_BASE] = LAYOUT(
        KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSLS, KC_GRV,  KC_PSCR, \
        KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSPC, KC_DEL,  \
        FN_ESC,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,          KC_ENT,  KC_PGUP, \
        KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT, KC_UP,   KC_PGDN, \
        KC_LCTL, KC_LGUI, KC_LALT,                   KC_SPC,                             KC_RALT, FN_FNLK,          KC_LEFT, KC_DOWN, KC_RGHT  \
    ),
    /* Function layer
     * ┌───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┬───┐
     * │   │F1 │F2 │F3 │F4 │F5 │F6 │F7 │F8 │F9 │F10│F11│F12│NLk│SLk│Pau│
     * ├───┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴───┼───┤
     * │     │M2 │M↑ │M1 │M3 │   │   │   │   │Stp│Ply│Prv│Nxt│Clear│Ins│
     * ├─────┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴┬──┴─────┼───┤
     * │      │M← │M↓ │M→ │MW↑│   │   │Mv←│ ↓ │ ↑ │Mv→│   │        │Top│
     * ├──────┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴─┬─┴────┬───┼───┤
     * │        │MA0│MA2│MW←│MW→│   │   │App│Vo-│Vo+│Mut│      │PgU│Btm│
     * ├────┬───┴┬──┴─┬─┴───┴───┴───┴───┴───┴──┬┴───┼───┴┬─┬───┼───┼───┤
     * │    │DtPR│DtNA│          MW↓           │    │    │ │Hom│PgD│End│
     * └────┴────┴────┴────────────────────────┴────┴────┘ └───┴───┴───┘
     */
    [L_FN] = LAYOUT(
        _______, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_NLCK, KC_SLCK, KC_PAUS, \
        _______, KC_BTN2, KC_MS_U, KC_BTN1, KC_BTN3, _______, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, CLEAR,   KC_INS,  \
        _______, KC_MS_L, KC_MS_D, KC_MS_R, KC_WH_U, _______, MV_LEFT, KC_DOWN, KC_UP,   MV_RGHT, _______, _______,          _______, TOP,     \
        _______, KC_ACL0, KC_ACL2, KC_WH_L, KC_WH_R, _______, _______, KC_APP,  KC_VOLD, KC_VOLU, KC_MUTE,          _______, KC_PGUP, BOTTOM,  \
        _______, _______, _______,                   KC_WH_D,                            _______, _______,          KC_HOME, KC_PGDN, KC_END   \
    ),
 };
@@ -0,0 +1,6 @@
 BOOTMAGIC_ENABLE  = no
 COMMAND_ENABLE    = yes
 CONSOLE_ENABLE    = yes
 EXTRAKEY_ENABLE   = yes
 MOUSEKEY_ENABLE   = yes
 NKRO_ENABLE       = yes
@@ -0,0 +1,246 @@
 /*
 Copyright 2019 codybender
 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
 the Free Software Foundation, either version 2 of the License, or
 (at your option) any later version.
 This program is distributed in the hope that it will be useful,
 but WITHOUT ANY WARRANTY; without even the implied warranty of
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 GNU General Public License for more details.
 You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "config_common.h"
 /* USB Device descriptor parameter */
 #define VENDOR_ID       0xFEED
 #define PRODUCT_ID      0x6060
 #define DEVICE_VER      0x0001
 #define MANUFACTURER    KeyHive
 #define PRODUCT         maypad
 #define DESCRIPTION     Budget-friendly numpad
 /* key matrix size */
 #define MATRIX_ROWS 5
 #define MATRIX_COLS 4
 /*
 * Keyboard Matrix Assignments
 *
 * Change this to how you wired your keyboard
 * COLS: AVR pins used for columns, left to right
 * ROWS: AVR pins used for rows, top to bottom
 * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
 *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
 *
 */
 #define MATRIX_ROW_PINS { C6, D7, E6, B4, B5 }
 #define MATRIX_COL_PINS { F6, F7, B1, B3 }
 #define UNUSED_PINS
 /* COL2ROW, ROW2COL*/
 #define DIODE_DIRECTION COL2ROW
 /*
 * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
 */
 #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
 // #define BACKLIGHT_PIN B7
 // #define BACKLIGHT_BREATHING
 // #define BACKLIGHT_LEVELS 3
 // #define RGB_DI_PIN E2
 // #ifdef RGB_DI_PIN
 //   #define RGBLED_NUM 16
 //   #define RGBLIGHT_HUE_STEP 8
 //   #define RGBLIGHT_SAT_STEP 8
 //   #define RGBLIGHT_VAL_STEP 8
 //   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
 //   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
 // /*== all animations enable ==*/
 //   #define RGBLIGHT_ANIMATIONS
 // /*== or choose animations ==*/
 //   #define RGBLIGHT_EFFECT_BREATHING
 //   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
 //   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
 //   #define RGBLIGHT_EFFECT_SNAKE
 //   #define RGBLIGHT_EFFECT_KNIGHT
 //   #define RGBLIGHT_EFFECT_CHRISTMAS
 //   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
 //   #define RGBLIGHT_EFFECT_RGB_TEST
 //   #define RGBLIGHT_EFFECT_ALTERNATING
 // /*== customize breathing effect ==*/
 //   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
 //   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
 //   /*==== use exp() and sin() ====*/
 //   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
 //   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
 // #endif
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 /* define if matrix has ghost (lacks anti-ghosting diodes) */
 //#define MATRIX_HAS_GHOST
 /* number of backlight levels */
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 /* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
 * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
 */
 // #define GRAVE_ESC_CTRL_OVERRIDE
 /*
 * Force NKRO
 *
 * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
 * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
 * makefile for this to work.)
 *
 * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
 * until the next keyboard reset.
 *
 * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
 * fully operational during normal computer usage.
 *
 * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
 * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
 * bootmagic, NKRO mode will always be enabled until it is toggled again during a
 * power-up.
 *
 */
 //#define FORCE_NKRO
 /*
 * Magic Key Options
 *
 * Magic keys are hotkey commands that allow control over firmware functions of
 * the keyboard. They are best used in combination with the HID Listen program,
 * found here: https://www.pjrc.com/teensy/hid_listen.html
 *
 * The options below allow the magic key functionality to be changed. This is
 * useful if your keyboard/keypad is missing keys and you want magic key support.
 *
 */
 /* key combination for magic key command */
 /* defined by default; to change, uncomment and set to the combination you want */
 // #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
 /* control how magic key switches layers */
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
 /* override magic key keymap */
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
 //#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
 //#define MAGIC_KEY_HELP           H
 //#define MAGIC_KEY_HELP_ALT       SLASH
 //#define MAGIC_KEY_DEBUG          D
 //#define MAGIC_KEY_DEBUG_MATRIX   X
 //#define MAGIC_KEY_DEBUG_KBD      K
 //#define MAGIC_KEY_DEBUG_MOUSE    M
 //#define MAGIC_KEY_VERSION        V
 //#define MAGIC_KEY_STATUS         S
 //#define MAGIC_KEY_CONSOLE        C
 //#define MAGIC_KEY_LAYER0         0
 //#define MAGIC_KEY_LAYER0_ALT     GRAVE
 //#define MAGIC_KEY_LAYER1         1
 //#define MAGIC_KEY_LAYER2         2
 //#define MAGIC_KEY_LAYER3         3
 //#define MAGIC_KEY_LAYER4         4
 //#define MAGIC_KEY_LAYER5         5
 //#define MAGIC_KEY_LAYER6         6
 //#define MAGIC_KEY_LAYER7         7
 //#define MAGIC_KEY_LAYER8         8
 //#define MAGIC_KEY_LAYER9         9
 //#define MAGIC_KEY_BOOTLOADER     B
 //#define MAGIC_KEY_BOOTLOADER_ALT ESC
 //#define MAGIC_KEY_LOCK           CAPS
 //#define MAGIC_KEY_EEPROM         E
 //#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
 //#define MAGIC_KEY_NKRO           N
 //#define MAGIC_KEY_SLEEP_LED      Z
 /*
 * Feature disable options
 *  These options are also useful to firmware size reduction.
 */
 /* disable debug print */
 //#define NO_DEBUG
 /* disable print */
 //#define NO_PRINT
 /* disable action features */
 //#define NO_ACTION_LAYER
 //#define NO_ACTION_TAPPING
 //#define NO_ACTION_ONESHOT
 //#define NO_ACTION_MACRO
 //#define NO_ACTION_FUNCTION
 /*
 * MIDI options
 */
 /* Prevent use of disabled MIDI features in the keymap */
 //#define MIDI_ENABLE_STRICT 1
 /* enable basic MIDI features:
   - MIDI notes can be sent when in Music mode is on
 */
 //#define MIDI_BASIC
 /* enable advanced MIDI features:
   - MIDI notes can be added to the keymap
   - Octave shift and transpose
   - Virtual sustain, portamento, and modulation wheel
   - etc.
 */
 //#define MIDI_ADVANCED
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -0,0 +1,16 @@
 {
    "keyboard_name": "maypad", 
    "url": "https://keyhive.xyz/shop/may-pad", 
    "maintainer": "codybender", 
    "width": 4, 
    "height": 5, 
    "layouts": {
        "LAYOUT_numpad_5x4": {
            "layout": [{"label":"Num Lock", "x":0, "y":0}, {"label":"/", "x":1, "y":0}, {"label":"*", "x":2, "y":0}, {"label":"-", "x":3, "y":0}, {"label":"7", "x":0, "y":1}, {"label":"8", "x":1, "y":1}, {"label":"9", "x":2, "y":1}, {"label":"4", "x":0, "y":2}, {"label":"5", "x":1, "y":2}, {"label":"6", "x":2, "y":2}, {"label":"+", "x":3, "y":1, "h":2}, {"label":"1", "x":0, "y":3}, {"label":"2", "x":1, "y":3}, {"label":"3", "x":2, "y":3}, {"label":"0", "x":0, "y":4, "w":2}, {"label":".", "x":2, "y":4}, {"label":"Enter", "x":3, "y":3, "h":2}]
        },
        "LAYOUT_ortho_5x4": {
            "layout": [{"label":"Num Lock", "x":0, "y":0}, {"label":"/", "x":1, "y":0}, {"label":"*", "x":2, "y":0}, {"label":"-", "x":3, "y":0}, {"label":"7", "x":0, "y":1}, {"label":"8", "x":1, "y":1}, {"label":"9", "x":2, "y":1}, {"label":"+", "x":3, "y":1}, {"label":"4", "x":0, "y":2}, {"label":"5", "x":1, "y":2}, {"label":"6", "x":2, "y":2}, {"label":"+", "x":3, "y":2}, {"label":"1", "x":0, "y":3}, {"label":"2", "x":1, "y":3}, {"label":"3", "x":2, "y":3}, {"label":"Enter", "x":3, "y":3}, {"label":"0", "x":0, "y":4, "w":2}, {"label":".", "x":2, "y":4}, {"label":"Enter", "x":3, "y":4}]
        }
    }
 }
@@ -0,0 +1,19 @@
 /* Copyright 2019 codybender
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 // place overrides here
@@ -0,0 +1,40 @@
 /* Copyright 2019 codybender
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include QMK_KEYBOARD_H
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 	LAYOUT_numpad_5x4(
 		KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, 
    	KC_P7,            KC_P8,   KC_P9,            
    	KC_P4,            KC_P5,   KC_P6,   KC_PPLS, 
    	KC_P1,            KC_P2,   KC_P3,            
    	KC_P0,                     KC_PDOT, KC_PENT  
 	),
 };
 void matrix_init_user(void) {
 }
 void matrix_scan_user(void) {
 }
 void led_set_user(uint8_t usb_led) {
 }
@@ -0,0 +1 @@
 # The default keymap for maypad
@@ -0,0 +1,51 @@
 /* Copyright 2019 codybender
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include "maypad.h"
 // Optional override functions below.
 // You can leave any or all of these undefined.
 // These are only required if you want to perform custom actions.
 /*
 void matrix_init_kb(void) {
  // put your keyboard start-up code here
  // runs once when the firmware starts up
  matrix_init_user();
 }
 void matrix_scan_kb(void) {
  // put your looping keyboard code here
  // runs every cycle (a lot)
  matrix_scan_user();
 }
 bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
  // put your per-action keyboard code here
  // runs for every action, just before processing by the firmware
  return process_record_user(keycode, record);
 }
 void led_set_kb(uint8_t usb_led) {
  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
  led_set_user(usb_led);
 }
 */
@@ -0,0 +1,61 @@
 /* Copyright 2019 codybender
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "quantum.h"
 /* maypad numpad layout
 * .-------------------.
 * |NLCK|   /|   *|   -|
 * |-------------------|
 * |   7|   8|   9|    |
 * |--------------|    |
 * |   4|   5|   6|   +|
 * |-------------------|
 * |   1|   2|   3|    |
 * |--------------|    |
 * |        0|   .| Ent|
 * '-------------------'
 */
 // The first section contains all of the arguments
 // The second converts the arguments into a two-dimensional array
 #define LAYOUT_numpad_5x4( \
    k00, k01, k02, k03, \
    k10, k11, k12,      \
    k20, k21, k22, k13, \
    k30, k31, k32,      \
    k40,      k42, k33  \
 ) { \
    { k00, k01,   k02, k03   }, \
    { k10, k11,   k12, k13   }, \
    { k20, k21,   k22, KC_NO }, \
    { k30, k31,   k32, k33   }, \
    { k40, KC_NO, k42, KC_NO }  \
 }
 #define LAYOUT_ortho_5x4( \
    k00, k01, k02, k03, \
    k10, k11, k12, k13, \
    k20, k21, k22, k23, \
    k30, k31, k32, k33, \
    k40, k41, k42, k43  \
 ) { \
    { k00, k01, k02, k03 }, \
    { k10, k11, k12, k13 }, \
    { k20, k21, k22, k23 }, \
    { k30, k31, k32, k33 }, \
    { k40, k41, k42, k43 }  \
 }
@@ -0,0 +1,13 @@
 # KeyHive Maypad
 ![Maypad Layout](https://i.imgur.com/B7WXcfy.png)
 A budget-friendly, exposed-component numpad from [KeyHive](https://www.keyhive.xyz)
 Keyboard Maintainer: [Cody Bender](https://github.com/codybender)  
 Make example for this keyboard (after setting up your build environment):
    make keyhive/maypad:default
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@@ -0,0 +1,82 @@
 # MCU name
 MCU = atmega32u4
 # Processor frequency.
 #     This will define a symbol, F_CPU, in all source code files equal to the
 #     processor frequency in Hz. You can then use this symbol in your source code to
 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
 #     automatically to create a 32-bit value in your source code.
 #
 #     This will be an integer division of F_USB below, as it is sourced by
 #     F_USB after it has run through any CPU prescalers. Note that this value
 #     does not *change* the processor frequency - it should merely be updated to
 #     reflect the processor speed set externally so that the code can use accurate
 #     software delays.
 F_CPU = 16000000
 #
 # LUFA specific
 #
 # Target architecture (see library "Board Types" documentation).
 ARCH = AVR8
 # Input clock frequency.
 #     This will define a symbol, F_USB, in all source code files equal to the
 #     input clock frequency (before any prescaling is performed) in Hz. This value may
 #     differ from F_CPU if prescaling is used on the latter, and is required as the
 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
 #     at the end, this will be done automatically to create a 32-bit value in your
 #     source code.
 #
 #     If no clock division is performed on the input clock inside the AVR (via the
 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 # Interrupt driven control endpoint task(+60)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
 #   atmega32a    bootloadHID
 BOOTLOADER = atmel-dfu
 # If you don't know the bootloader type, then you can specify the
 # Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
 #   Teensy halfKay      512
 #   Teensy++ halfKay    1024
 #   Atmel DFU loader    4096
 #   LUFA bootloader     4096
 #   USBaspLoader        2048
 # OPT_DEFS += -DBOOTLOADER_SIZE=4096
 # Build Options
 #   change yes to no to disable
 #
 BOOTMAGIC_ENABLE = lite      # Virtual DIP switch configuration(+1000)
 MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
 EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
 CONSOLE_ENABLE = yes        # Console for debug(+400)
 COMMAND_ENABLE = yes        # Commands for debug and configuration
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
 NKRO_ENABLE = no            # USB Nkey Rollover
 BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
 RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
 MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
 UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 LAYOUTS = ortho_5x4 numpad_5x4
@@ -11,4 +11,3 @@
        }
    }
 }
 rt
@@ -0,0 +1,101 @@
 {
    "keyboard_name": "NEK Type A",
    "url": "",
    "maintainer": "ecopoesis",
    "width": 19.75,
    "height": 6.25,
    "layouts": {
        "LAYOUT": {
            "layout": [
                {"label":"Esc", "x":0.5, "y":0, "w":1.75},
                {"label":"F1", "x":2.75, "y":0},
                {"label":"F2", "x":3.75, "y":0},
                {"label":"F3", "x":4.75, "y":0},
                {"label":"F4", "x":5.75, "y":0},
                {"label":"F5", "x":8.25, "y":0},
                {"label":"F6", "x":9.25, "y":0},
                {"label":"F7", "x":10.25, "y":0},
                {"label":"F8", "x":11.25, "y":0},
                {"label":"F9", "x":12.5, "y":0},
                {"label":"F10", "x":13.5, "y":0},
                {"label":"F11", "x":14.5, "y":0},
                {"label":"F12", "x":15.5, "y":0},
                {"label":"Mute", "x":16.75, "y":0},
                {"label":"Volume Down", "x":17.75, "y":0},
                {"label":"Volume Up", "x":18.75, "y":0},
                {"label":"`", "x":0, "y":1.25},
                {"label":"1", "x":1, "y":1.25},
                {"label":"2", "x":2, "y":1.25},
                {"label":"3", "x":3, "y":1.25},
                {"label":"4", "x":4, "y":1.25},
                {"label":"5", "x":5, "y":1.25},
                {"label":"6", "x":6, "y":1.25},
                {"label":"7", "x":8, "y":1.25, "w":1.5},
                {"label":"8", "x":9.5, "y":1.25},
                {"label":"9", "x":10.5, "y":1.25},
                {"label":"0", "x":11.5, "y":1.25},
                {"label":"-", "x":12.5, "y":1.25},
                {"label":"=", "x":13.5, "y":1.25},
                {"label":"Backspace", "x":14.5, "y":1.25, "w":2},
                {"label":"Insert", "x":16.75, "y":1.25},
                {"label":"Home", "x":17.75, "y":1.25},
                {"label":"Page Up", "x":18.75, "y":1.25},
                {"label":"Tab", "x":0, "y":2.25, "w":1.5},
                {"label":"Q", "x":1.5, "y":2.25},
                {"label":"W", "x":2.5, "y":2.25},
                {"label":"E", "x":3.5, "y":2.25},
                {"label":"R", "x":4.5, "y":2.25},
                {"label":"T", "x":5.5, "y":2.25, "w":1.5},
                {"label":"Y", "x":8, "y":2.25},
                {"label":"U", "x":9, "y":2.25},
                {"label":"I", "x":10, "y":2.25},
                {"label":"O", "x":11, "y":2.25},
                {"label":"P", "x":12, "y":2.25},
                {"label":"[", "x":13, "y":2.25},
                {"label":"]", "x":14, "y":2.25},
                {"label":"\\", "x":15, "y":2.25, "w":1.5},
                {"label":"Delete", "x":16.75, "y":2.25},
                {"label":"End", "x":17.75, "y":2.25},
                {"label":"Page Down", "x":18.75, "y":2.25},
                {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75},
                {"label":"A", "x":1.75, "y":3.25},
                {"label":"S", "x":2.75, "y":3.25},
                {"label":"D", "x":3.75, "y":3.25},
                {"label":"F", "x":4.75, "y":3.25},
                {"label":"G", "x":5.75, "y":3.25, "w":1.25},
                {"label":"H", "x":8, "y":3.25, "w":1.25},
                {"label":"J", "x":9.25, "y":3.25},
                {"label":"K", "x":10.25, "y":3.25},
                {"label":"L", "x":11.25, "y":3.25},
                {"label":";", "x":12.25, "y":3.25},
                {"label":"'", "x":13.25, "y":3.25},
                {"label":"Enter", "x":14.25, "y":3.25, "w":2.25},
                {"label":"Shift", "x":0, "y":4.25, "w":2},
                {"label":"Z", "x":2, "y":4.25},
                {"label":"X", "x":3, "y":4.25},
                {"label":"C", "x":4, "y":4.25},
                {"label":"V", "x":5, "y":4.25},
                {"label":"B", "x":6, "y":4.25},
                {"label":"N", "x":8, "y":4.25, "w":1.5},
                {"label":"M", "x":9.5, "y":4.25},
                {"label":",", "x":10.5, "y":4.25},
                {"label":".", "x":11.5, "y":4.25},
                {"label":"/", "x":12.5, "y":4.25},
                {"label":"Shift", "x":13.5, "y":4.25, "w":2.75},
                {"label":"Up", "x":17.75, "y":3.75},
                {"label":"Ctrl", "x":0, "y":5.25, "w":1.5},
                {"label":"Alt", "x":1.5, "y":5.25, "w":1.25},
                {"label":"Cmd", "x":2.75, "y":5.25, "w":1.5},
                {"label":"Space", "x":4.25, "y":5.25, "w":2.75},
                {"label":"Space", "x":8, "y":5.25, "w":2.75},
                {"label":"Cmd", "x":10.75, "y":5.25, "w":1.5},
                {"label":"Alt", "x":12.25, "y":5.25, "w":1.25},
                {"label":"Ctrl", "x":13.5, "y":5.25, "w":1.5},
                {"label":"Menu", "x":15, "y":5.25, "w":1.25},
                {"label":"Left", "x":16.75, "y":4.75},
                {"label":"Down", "x":17.75, "y":4.75},
                {"label":"Right", "x":18.75, "y":4.75}
            ]
        }
    }
 }
@@ -0,0 +1,5 @@
 #pragma once
 #define NO_ACTION_ONESHOT
 #define NO_ACTION_MACRO
 #define NO_ACTION_FUNCTION
 #define TAPPING_TOGGLE  2
@@ -0,0 +1,146 @@
 #include QMK_KEYBOARD_H
 #include <keymap_steno.h>
 enum planck_layers {
  _BA,        // Base (Balance Twelve mirror variant)
  _PL,        // Plover (http://opensteno.org)
  _NP,        // Numeric/punctuation
  _FC         // Function/cursor
 };
 enum planck_keycodes {
  BA  = SAFE_RANGE,
  PL
 };
 // Abbreviations
 #define KX_SFT_Z   MT(MOD_LSFT, KC_Z)
 #define KX_SFT_X   MT(MOD_RSFT, KC_X)
 #define LT_ESC_FC  LT(_FC, KC_ESC)
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  /* BA
    .--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.
    | P      | L      | C      | D      | W      |        |        | U      | O      | Y      | K      | Q      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | N      | R      | S      | T      | M      |        | BS     | A      | E      | I      | H      | V      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Z Sft  | J      | F      | G      | B      |        | Ent    | ' @    | , <    | . >    | X Sft  |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Ctl    | Alt    | Sup    | NP     | Spc    | Esc/FC | Sft    | Sft    | Sup    | Alt    | Ctl    |        |
    '--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'
  */                                                                                                            
  [_BA] = LAYOUT_planck_grid( 
    KC_P,     KC_L,    KC_C,    KC_D,    KC_W,   XXXXXXX,   XXXXXXX, KC_U,    KC_O,    KC_Y,    KC_K,     KC_Q,
    KC_N,     KC_R,    KC_S,    KC_T,    KC_M,   XXXXXXX,   KC_BSPC, KC_A,    KC_E,    KC_I,    KC_H,     KC_V,
    KX_SFT_Z, KC_J,    KC_F,    KC_G,    KC_B,   XXXXXXX,   KC_ENT,  KC_QUOT, KC_COMM, KC_DOT,  KX_SFT_X, XXXXXXX,
    KC_LCTL,  KC_LALT, KC_LGUI, MO(_NP), KC_SPC, LT_ESC_FC, KC_LSFT, KC_LSFT, KC_LGUI, KC_LALT, KC_LCTL,  XXXXXXX
  ),
  /* Plover
    .--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.
    | #      | #      | #      | #      | #      | BA     | #      | #      | #      | #      | #      | #      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | S      | T      | P      | H      | *      |        | *      | F      | P      | L      | T      | D      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | S      | K      | W      | R      | *      |        | *      | R      | B      | G      | S      | Z      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    |        |        |        | A      | O      |        | E      | U      |        |        |        |        |
    '--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'
  */
  [_PL] = LAYOUT_planck_grid(
    STN_NUM, STN_NUM, STN_NUM, STN_NUM, STN_NUM, BA,      STN_NUM, STN_NUM, STN_NUM, STN_NUM, STN_NUM, STN_NUM,
    STN_S1,  STN_TL,  STN_PL,  STN_HL,  STN_ST1, XXXXXXX, STN_ST1, STN_FR,  STN_PR,  STN_LR,  STN_TR,  STN_DR,
    STN_S2,  STN_KL,  STN_WL,  STN_RL,  STN_ST2, XXXXXXX, STN_ST2, STN_RR,  STN_BR,  STN_GR,  STN_SR,  STN_ZR,
    XXXXXXX, XXXXXXX, XXXXXXX, STN_A,   STN_O,   XXXXXXX, STN_E,   STN_U,   XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX
  ),
  /* Numeric/punctuation
    .--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.
    | 1 !    | 2 "    | 3 £    | 4 $    | 5 %    | PL     |        | 6 ^    | 7 &    | 8 *    | 9 (    | 0 )    |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Tab    | Ctl-X  | Ctl-C  | Ctl-V  | Ctl-Z  |        | BS     | [ {    | ] }    | - _    | ; :    | \ |    |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Sft    |        |        | Del    | Ins    |        |        | / ?    | = +    | # ~    | `      |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Ctl    | Alt    | Sup    | NP     | Spc    |        | Sft    | Sft    | Sup    | Alt    | Ctl    |        |
    '--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'
  */                                           
  [_NP] = LAYOUT_planck_grid(
    KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    PL,      XXXXXXX, KC_6,    KC_7,    KC_8,    KC_9,    KC_0,
    KC_TAB,  C(KC_X), C(KC_C), C(KC_V), C(KC_Z), XXXXXXX, _______, KC_LBRC, KC_RBRC, KC_MINS, KC_SCLN, KC_NUBS,
    KC_LSFT, XXXXXXX, XXXXXXX, KC_DEL,  KC_INS,  XXXXXXX, XXXXXXX, KC_SLSH, KC_EQL,  KC_NUHS, KC_GRV,  XXXXXXX, 
    _______, _______, _______, _______, _______, XXXXXXX, _______, _______, _______, _______, _______, XXXXXXX
  ),
  /* Function/cursor
    .--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.
    | F1     | F2     | F3     | F4     | F5     |        |        | Home   | Up     | End    | PgUp   |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | F6     | F7     | F8     | F9     | F10    |        |        | Left   | Down   | Right  | PgDn   |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Sft    |        |        | F11    | F12    |        |        | PScr   | Break  | ScLk   | Caps   |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Ctl    | Alt    | Sup    |        | Spc    |        | Sft    | Sft    | Sup    | Alt    | Ctl    |        |
    '--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'
  */                                                                                                            
  [_FC] = LAYOUT_planck_grid(
    KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   XXXXXXX, XXXXXXX, KC_HOME, KC_UP,   KC_END,  KC_PGUP, XXXXXXX,
    KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  XXXXXXX, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT, KC_PGDN, XXXXXXX,
    _______, XXXXXXX, XXXXXXX, KC_F11,  KC_F12,  XXXXXXX, XXXXXXX, KC_PSCR, KC_BRK,  KC_SLCK, KC_CAPS, XXXXXXX,
    _______, _______, _______, XXXXXXX, _______, _______, _______, _______, _______, _______, _______, XXXXXXX
  )
 };
 #ifdef AUDIO_ENABLE
  float plover_on[][2]   = SONG(PLOVER_SOUND);
  float plover_off[][2]  = SONG(PLOVER_GOODBYE_SOUND);
 #endif
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
  switch (keycode) {
    case PL:
      if (record->event.pressed) {
        #ifdef AUDIO_ENABLE
          stop_all_notes();
          PLAY_SONG(plover_on);
        #endif
        layer_off(_NP);
        layer_off(_FC);
        layer_on(_PL);
        if (!eeconfig_is_enabled()) {
            eeconfig_init();
        }
        keymap_config.raw = eeconfig_read_keymap();
        keymap_config.nkro = 1;
        eeconfig_update_keymap(keymap_config.raw);
      }
      return false;
    case BA:
      if (record->event.pressed) {
        #ifdef AUDIO_ENABLE
          PLAY_SONG(plover_off);
        #endif
        layer_off(_NP);
        layer_off(_PL);
        layer_off(_FC);
      }
      return false;
    }
    return true;
 }
 void matrix_init_user() {
  steno_set_mode(STENO_MODE_GEMINI);
 }
@@ -0,0 +1,68 @@
 # Overview
 * Base layer uses the Balance Twelve layout ([reference](https://mathematicalmulticore.wordpress.com/the-keyboard-layout-project/))
 * Plover layer uses the same home position as the base layer ([reference](http://www.openstenoproject.org/))
 ## To build
 ```
 make planck/rev6:yttyx
 ```
 ## To build and flash
 ```
 make planck/rev6:yttyx:dfu-util
 ```
 ## Layers
 ### Base
    .--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.
    | P      | L      | C      | D      | W      |        |        | U      | O      | Y      | K      | Q      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | N      | R      | S      | T      | M      |        | BS     | A      | E      | I      | H      | V      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Z Sft  | J      | F      | G      | B      |        | Ent    | ' @    | , <    | . >    | X Sft  |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Ctl    | Alt    | Sup    | NP     | Spc    | Esc/FC | Sft    | Sft    | Sup    | Alt    | Ctl    |        |
    '--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'
 ### Plover
    .--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.
    | #      | #      | #      | #      | #      | BA     | #      | #      | #      | #      | #      | #      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | S      | T      | P      | H      | *      |        | *      | F      | P      | L      | T      | D      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | S      | K      | W      | R      | *      |        | *      | R      | B      | G      | S      | Z      |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    |        |        |        | A      | O      |        | E      | U      |        |        |        |        |
    '--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'
 ### Numeric/Punctuation
    .--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.
    | 1 !    | 2 "    | 3 £    | 4 $    | 5 %    | PL     |        | 6 ^    | 7 &    | 8 *    | 9 (    | 0 )    |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Tab    | Ctl-X  | Ctl-C  | Ctl-V  | Ctl-Z  |        | BS     | [ {    | ] }    | - _    | ; :    | \ |    |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Sft    |        |        | Del    | Ins    |        |        | / ?    | = +    | # ~    | `      |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Ctl    | Alt    | Sup    | NP     | Spc    |        | Sft    | Sft    | Sup    | Alt    | Ctl    |        |
    '--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'
 ### Function
    .--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.--------.
    | F1     | F2     | F3     | F4     | F5     |        |        | Home   | Up     | End    | PgUp   |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | F6     | F7     | F8     | F9     | F10    |        |        | Left   | Down   | Right  | PgDn   |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Sft    |        |        | F11    | F12    |        |        | PScr   | Break  | ScLk   | Caps   |        |
    |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------|
    | Ctl    | Alt    | Sup    |        | Spc    |        | Sft    | Sft    | Sup    | Alt    | Ctl    |        |
    '--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'--------'
@@ -0,0 +1,11 @@
 # Build Options
 AUDIO_ENABLE = yes
 CONSOLE_ENABLE = no
 EXTRAKEY_ENABLE = no
 MIDI_ENABLE = no
 MOUSEKEY_ENABLE = no
 NKRO_ENABLE = yes
 RGBLIGHT_ENABLE = no
 STENO_ENABLE = yes
 VIRTSER_ENABLE = yes
@@ -26,8 +26,8 @@
 /* key matrix size */
 // Rows are doubled-up
-#define MATRIX_ROWS 10
+#define MATRIX_ROWS 6
-#define MATRIX_COLS 8
+#define MATRIX_COLS 6
 // wiring of each half
 #define MATRIX_ROW_PINS { D4, C6, D7 }
@@ -51,9 +51,10 @@
 /* ws2812 RGB LED */
 #define RGB_DI_PIN D3
 #define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 70
+#define RGBLED_NUM 36
 #define RGBLIGHT_SPLIT
-#define RGBLED_SPLIT { 35, 35 }    // Number of LEDs
+#define RGBLED_SPLIT { 18, 18 }    // Number of LEDs
 #define RGBLIGHT_LIMIT_VAL 100
 #define SOFT_SERIAL_PIN D2
 #define SELECT_SOFT_SERIAL_SPEED 1
@@ -26,8 +26,8 @@
 /* key matrix size */
 // Rows are doubled-up
-#define MATRIX_ROWS 10
+#define MATRIX_ROWS 6
-#define MATRIX_COLS 8
+#define MATRIX_COLS 7
 // wiring of each half
 #define MATRIX_ROW_PINS { D4, C6, D7 }
@@ -51,9 +51,10 @@
 /* ws2812 RGB LED */
 #define RGB_DI_PIN D3
 #define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 70
+#define RGBLED_NUM 42
 #define RGBLIGHT_SPLIT
-#define RGBLED_SPLIT { 35, 35 }    // Number of LEDs
+#define RGBLED_SPLIT { 21, 21 }    // Number of LEDs
 #define RGBLIGHT_LIMIT_VAL 100
 #define SOFT_SERIAL_PIN D2
 #define SELECT_SOFT_SERIAL_SPEED 1
@@ -26,7 +26,7 @@
 /* key matrix size */
 // Rows are doubled-up
-#define MATRIX_ROWS 10
+#define MATRIX_ROWS 6
 #define MATRIX_COLS 8
 // wiring of each half
@@ -51,9 +51,10 @@
 /* ws2812 RGB LED */
 #define RGB_DI_PIN D3
 #define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 80
+#define RGBLED_NUM 48
 #define RGBLIGHT_SPLIT
-#define RGBLED_SPLIT { 40, 40 }    // Number of LEDs
+#define RGBLED_SPLIT { 24, 24 }    // Number of LEDs
 #define RGBLIGHT_LIMIT_VAL 100
 #define SOFT_SERIAL_PIN D2
 #define SELECT_SOFT_SERIAL_SPEED 1
@@ -26,8 +26,8 @@
 /* key matrix size */
 // Rows are doubled-up
-#define MATRIX_ROWS 10
+#define MATRIX_ROWS 8
-#define MATRIX_COLS 8
+#define MATRIX_COLS 6
 // wiring of each half
 #define MATRIX_ROW_PINS { D4, C6, D7, E6 }
@@ -51,9 +51,10 @@
 /* ws2812 RGB LED */
 #define RGB_DI_PIN D3
 #define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 70
+#define RGBLED_NUM 48
 #define RGBLIGHT_SPLIT
-#define RGBLED_SPLIT { 35, 35 }    // Number of LEDs
+#define RGBLED_SPLIT { 24, 24 }    // Number of LEDs
 #define RGBLIGHT_LIMIT_VAL 100
 #define SOFT_SERIAL_PIN D2
 #define SELECT_SOFT_SERIAL_SPEED 1
@@ -26,8 +26,8 @@
 /* key matrix size */
 // Rows are doubled-up
-#define MATRIX_ROWS 10
+#define MATRIX_ROWS 8
-#define MATRIX_COLS 8
+#define MATRIX_COLS 7
 // wiring of each half
 #define MATRIX_ROW_PINS { D4, C6, D7, E6 }
@@ -51,9 +51,10 @@
 /* ws2812 RGB LED */
 #define RGB_DI_PIN D3
 #define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 70
+#define RGBLED_NUM 56
 #define RGBLIGHT_SPLIT
-#define RGBLED_SPLIT { 35, 35 }    // Number of LEDs
+#define RGBLED_SPLIT { 28, 28 }    // Number of LEDs
 #define RGBLIGHT_LIMIT_VAL 100
 #define SOFT_SERIAL_PIN D2
 #define SELECT_SOFT_SERIAL_SPEED 1
@@ -26,7 +26,7 @@
 /* key matrix size */
 // Rows are doubled-up
-#define MATRIX_ROWS 10
+#define MATRIX_ROWS 8
 #define MATRIX_COLS 8
 // wiring of each half
@@ -51,9 +51,10 @@
 /* ws2812 RGB LED */
 #define RGB_DI_PIN D3
 #define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 80
+#define RGBLED_NUM 64
 #define RGBLIGHT_SPLIT
-#define RGBLED_SPLIT { 40, 40 }    // Number of LEDs
+#define RGBLED_SPLIT { 32, 32 }    // Number of LEDs
 #define RGBLIGHT_LIMIT_VAL 100
 #define SOFT_SERIAL_PIN D2
 #define SELECT_SOFT_SERIAL_SPEED 1
@@ -27,7 +27,7 @@
 /* key matrix size */
 // Rows are doubled-up
 #define MATRIX_ROWS 10
-#define MATRIX_COLS 8
+#define MATRIX_COLS 6
 // wiring of each half
 #define MATRIX_ROW_PINS { D4, C6, D7, E6, B4 }
@@ -51,9 +51,10 @@
 /* ws2812 RGB LED */
 #define RGB_DI_PIN D3
 #define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 70
+#define RGBLED_NUM 60
 #define RGBLIGHT_SPLIT
-#define RGBLED_SPLIT { 35, 35 }    // Number of LEDs
+#define RGBLED_SPLIT { 30, 30 }    // Number of LEDs
 #define RGBLIGHT_LIMIT_VAL 100
 #define SOFT_SERIAL_PIN D2
 #define SELECT_SOFT_SERIAL_SPEED 1
@@ -27,7 +27,7 @@
 /* key matrix size */
 // Rows are doubled-up
 #define MATRIX_ROWS 10
-#define MATRIX_COLS 8
+#define MATRIX_COLS 7
 // wiring of each half
 #define MATRIX_ROW_PINS { D4, C6, D7, E6, B4 }
@@ -54,6 +54,7 @@
 #define RGBLED_NUM 70
 #define RGBLIGHT_SPLIT
 #define RGBLED_SPLIT { 35, 35 }    // Number of LEDs
 #define RGBLIGHT_LIMIT_VAL 100
 #define SOFT_SERIAL_PIN D2
 #define SELECT_SOFT_SERIAL_SPEED 1
@@ -54,6 +54,7 @@
 #define RGBLED_NUM 80
 #define RGBLIGHT_SPLIT
 #define RGBLED_SPLIT { 40, 40 }    // Number of LEDs
 #define RGBLIGHT_LIMIT_VAL 100
 #define SOFT_SERIAL_PIN D2
 #define SELECT_SOFT_SERIAL_SPEED 1
@@ -38,10 +38,10 @@ BOOTLOADER = caterina
 #   change yes to no to disable
 #
 BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+EXTRAKEY_ENABLE = no       # Audio control and System control(+450)
-CONSOLE_ENABLE = yes        # Console for debug(+400)
+CONSOLE_ENABLE = no        # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
+COMMAND_ENABLE = no        # Commands for debug and configuration
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
@@ -7,11 +7,231 @@
  "layouts": {  
    "LAYOUT_96_ansi": {
      "key_count": 99,
-      "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":1, "y":0}, {"label":"F2", "x":2, "y":0}, {"label":"F3", "x":3, "y":0}, {"label":"F4", "x":4, "y":0}, {"label":"F5", "x":5, "y":0}, {"label":"F6", "x":6, "y":0}, {"label":"F7", "x":7, "y":0}, {"label":"F8", "x":8, "y":0}, {"label":"F9", "x":9, "y":0}, {"label":"F10", "x":10, "y":0}, {"label":"F11", "x":11, "y":0}, {"label":"F12", "x":12, "y":0}, {"label":"Insert", "x":13, "y":0}, {"label":"Delete", "x":14, "y":0}, {"label":"Home", "x":15, "y":0}, {"label":"End", "x":16, "y":0}, {"label":"PgUp", "x":17, "y":0}, {"label":"PgDn", "x":18, "y":0}, {"label":"~", "x":0, "y":1}, {"label":"!", "x":1, "y":1}, {"label":"@", "x":2, "y":1}, {"label":"#", "x":3, "y":1}, {"label":"$", "x":4, "y":1}, {"label":"%", "x":5, "y":1}, {"label":"^", "x":6, "y":1}, {"label":"&", "x":7, "y":1}, {"label":"*", "x":8, "y":1}, {"label":"(", "x":9, "y":1}, {"label":")", "x":10, "y":1}, {"label":"_", "x":11, "y":1}, {"label":"+", "x":12, "y":1}, {"label":"Backspace", "x":13, "y":1, "w":2}, {"label":"Num Lock", "x":15, "y":1}, {"label":"/", "x":16, "y":1}, {"label":"*", "x":17, "y":1}, {"label":"-", "x":18, "y":1}, {"label":"Tab", "x":0, "y":2, "w":1.5}, {"label":"Q", "x":1.5, "y":2}, {"label":"W", "x":2.5, "y":2}, {"label":"E", "x":3.5, "y":2}, {"label":"R", "x":4.5, "y":2}, {"label":"T", "x":5.5, "y":2}, {"label":"Y", "x":6.5, "y":2}, {"label":"U", "x":7.5, "y":2}, {"label":"I", "x":8.5, "y":2}, {"label":"O", "x":9.5, "y":2}, {"label":"P", "x":10.5, "y":2}, {"label":"{", "x":11.5, "y":2}, {"label":"}", "x":12.5, "y":2}, {"label":"|", "x":13.5, "y":2, "w":1.5}, {"label":"7", "x":15, "y":2}, {"label":"8", "x":16, "y":2}, {"label":"9", "x":17, "y":2}, {"label":"+", "x":18, "y":2, "h":2}, {"label":"Caps Lock", "x":0, "y":3, "w":1.75}, {"label":"A", "x":1.75, "y":3}, {"label":"S", "x":2.75, "y":3}, {"label":"D", "x":3.75, "y":3}, {"label":"F", "x":4.75, "y":3}, {"label":"G", "x":5.75, "y":3}, {"label":"H", "x":6.75, "y":3}, {"label":"J", "x":7.75, "y":3}, {"label":"K", "x":8.75, "y":3}, {"label":"L", "x":9.75, "y":3}, {"label":":", "x":10.75, "y":3}, {"label":"\"", "x":11.75, "y":3}, {"label":"Enter", "x":12.75, "y":3, "w":2.25}, {"label":"4", "x":15, "y":3}, {"label":"5", "x":16, "y":3}, {"label":"6", "x":17, "y":3}, {"label":"Shift", "x":0, "y":4, "w":2.25}, {"label":"Z", "x":2.25, "y":4}, {"label":"X", "x":3.25, "y":4}, {"label":"C", "x":4.25, "y":4}, {"label":"V", "x":5.25, "y":4}, {"label":"B", "x":6.25, "y":4}, {"label":"N", "x":7.25, "y":4}, {"label":"M", "x":8.25, "y":4}, {"label":"<", "x":9.25, "y":4}, {"label":">", "x":10.25, "y":4}, {"label":"?", "x":11.25, "y":4}, {"label":"Shift", "x":12.25, "y":4, "w":1.75}, {"label":"\u2191", "x":14, "y":4}, {"label":"1", "x":15, "y":4}, {"label":"2", "x":16, "y":4}, {"label":"3", "x":17, "y":4}, {"label":"Enter", "x":18, "y":4, "h":2}, {"label":"Ctrl", "x":0, "y":5, "w":1.25}, {"label":"Win", "x":1.25, "y":5, "w":1.25}, {"label":"Alt", "x":2.5, "y":5, "w":1.25}, {"x":3.75, "y":5, "w":6.25}, {"label":"Alt", "x":10, "y":5, "w":1.5}, {"label":"Ctrl", "x":11.5, "y":5, "w":1.5}, {"label":"\u2190", "x":13, "y":5}, {"label":"\u2193", "x":14, "y":5}, {"label":"\u2192", "x":15, "y":5}, {"label":"0", "x":16, "y":5}, {"label":".", "x":17, "y":5}]
+      "layout": [
        {"label":"Esc", "x":0, "y":0},
        {"label":"F1", "x":1, "y":0},
        {"label":"F2", "x":2, "y":0},
        {"label":"F3", "x":3, "y":0},
        {"label":"F4", "x":4, "y":0},
        {"label":"F5", "x":5, "y":0},
        {"label":"F6", "x":6, "y":0},
        {"label":"F7", "x":7, "y":0},
        {"label":"F8", "x":8, "y":0},
        {"label":"F9", "x":9, "y":0},
        {"label":"F10", "x":10, "y":0},
        {"label":"F11", "x":11, "y":0},
        {"label":"F12", "x":12, "y":0},
        {"label":"Insert", "x":13, "y":0},
        {"label":"Delete", "x":14, "y":0},
        {"label":"Home", "x":15, "y":0},
        {"label":"End", "x":16, "y":0},
        {"label":"PgUp", "x":17, "y":0},
        {"label":"PgDn", "x":18, "y":0},
        {"label":"~", "x":0, "y":1},
        {"label":"!", "x":1, "y":1},
        {"label":"@", "x":2, "y":1},
        {"label":"#", "x":3, "y":1},
        {"label":"$", "x":4, "y":1},
        {"label":"%", "x":5, "y":1},
        {"label":"^", "x":6, "y":1},
        {"label":"&", "x":7, "y":1},
        {"label":"*", "x":8, "y":1},
        {"label":"(", "x":9, "y":1},
        {"label":")", "x":10, "y":1},
        {"label":"_", "x":11, "y":1},
        {"label":"+", "x":12, "y":1},
        {"label":"Backspace", "x":13, "y":1, "w":2},
        {"label":"Num Lock", "x":15, "y":1},
        {"label":"/", "x":16, "y":1},
        {"label":"*", "x":17, "y":1},
        {"label":"-", "x":18, "y":1},
        {"label":"Tab", "x":0, "y":2, "w":1.5},
        {"label":"Q", "x":1.5, "y":2},
        {"label":"W", "x":2.5, "y":2},
        {"label":"E", "x":3.5, "y":2},
        {"label":"R", "x":4.5, "y":2},
        {"label":"T", "x":5.5, "y":2},
        {"label":"Y", "x":6.5, "y":2},
        {"label":"U", "x":7.5, "y":2},
        {"label":"I", "x":8.5, "y":2},
        {"label":"O", "x":9.5, "y":2},
        {"label":"P", "x":10.5, "y":2},
        {"label":"{", "x":11.5, "y":2},
        {"label":"}", "x":12.5, "y":2},
        {"label":"|", "x":13.5, "y":2, "w":1.5},
        {"label":"7", "x":15, "y":2},
        {"label":"8", "x":16, "y":2},
        {"label":"9", "x":17, "y":2},
        {"label":"Caps Lock", "x":0, "y":3, "w":1.75},
        {"label":"A", "x":1.75, "y":3},
        {"label":"S", "x":2.75, "y":3},
        {"label":"D", "x":3.75, "y":3},
        {"label":"F", "x":4.75, "y":3},
        {"label":"G", "x":5.75, "y":3},
        {"label":"H", "x":6.75, "y":3},
        {"label":"J", "x":7.75, "y":3},
        {"label":"K", "x":8.75, "y":3},
        {"label":"L", "x":9.75, "y":3},
        {"label":":", "x":10.75, "y":3},
        {"label":"\"", "x":11.75, "y":3},
        {"label":"Enter", "x":12.75, "y":3, "w":2.25},
        {"label":"4", "x":15, "y":3},
        {"label":"5", "x":16, "y":3},
        {"label":"6", "x":17, "y":3},
        {"label":"+", "x":18, "y":2, "h":2},
        {"label":"Shift", "x":0, "y":4, "w":2.25},
        {"label":"Z", "x":2.25, "y":4},
        {"label":"X", "x":3.25, "y":4},
        {"label":"C", "x":4.25, "y":4},
        {"label":"V", "x":5.25, "y":4},
        {"label":"B", "x":6.25, "y":4},
        {"label":"N", "x":7.25, "y":4},
        {"label":"M", "x":8.25, "y":4},
        {"label":"<", "x":9.25, "y":4},
        {"label":">", "x":10.25, "y":4},
        {"label":"?", "x":11.25, "y":4},
        {"label":"Shift", "x":12.25, "y":4, "w":1.75},
        {"label":"\u2191", "x":14, "y":4},
        {"label":"1", "x":15, "y":4},
        {"label":"2", "x":16, "y":4},
        {"label":"3", "x":17, "y":4},
        {"label":"Ctrl", "x":0, "y":5, "w":1.25},
        {"label":"Win", "x":1.25, "y":5, "w":1.25},
        {"label":"Alt", "x":2.5, "y":5, "w":1.25},
        {"x":3.75, "y":5, "w":6.25},
        {"label":"Alt", "x":10, "y":5, "w":1.5},
        {"label":"Ctrl", "x":11.5, "y":5, "w":1.5},
        {"label":"\u2190", "x":13, "y":5},
        {"label":"\u2193", "x":14, "y":5},
        {"label":"\u2192", "x":15, "y":5},
        {"label":"0", "x":16, "y":5},
        {"label":".", "x":17, "y":5},
        {"label":"Enter", "x":18, "y":4, "h":2}
      ]
    },
    "LAYOUT_96_iso": {
      "key_count": 100,
-      "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":1, "y":0}, {"label":"F2", "x":2, "y":0}, {"label":"F3", "x":3, "y":0}, {"label":"F4", "x":4, "y":0}, {"label":"F5", "x":5, "y":0}, {"label":"F6", "x":6, "y":0}, {"label":"F7", "x":7, "y":0}, {"label":"F8", "x":8, "y":0}, {"label":"F9", "x":9, "y":0}, {"label":"F10", "x":10, "y":0}, {"label":"F11", "x":11, "y":0}, {"label":"F12", "x":12, "y":0}, {"label":"Insert", "x":13, "y":0}, {"label":"Delete", "x":14, "y":0}, {"label":"Home", "x":15, "y":0}, {"label":"End", "x":16, "y":0}, {"label":"PgUp", "x":17, "y":0}, {"label":"PgDn", "x":18, "y":0}, {"label":"~", "x":0, "y":1}, {"label":"!", "x":1, "y":1}, {"label":"\"", "x":2, "y":1}, {"label":"\u00a3", "x":3, "y":1}, {"label":"$", "x":4, "y":1}, {"label":"%", "x":5, "y":1}, {"label":"^", "x":6, "y":1}, {"label":"&", "x":7, "y":1}, {"label":"*", "x":8, "y":1}, {"label":"(", "x":9, "y":1}, {"label":")", "x":10, "y":1}, {"label":"_", "x":11, "y":1}, {"label":"+", "x":12, "y":1}, {"label":"Backspace", "x":13, "y":1, "w":2}, {"label":"Num Lock", "x":15, "y":1}, {"label":"/", "x":16, "y":1}, {"label":"*", "x":17, "y":1}, {"label":"-", "x":18, "y":1}, {"label":"Tab", "x":0, "y":2, "w":1.5}, {"label":"Q", "x":1.5, "y":2}, {"label":"W", "x":2.5, "y":2}, {"label":"E", "x":3.5, "y":2}, {"label":"R", "x":4.5, "y":2}, {"label":"T", "x":5.5, "y":2}, {"label":"Y", "x":6.5, "y":2}, {"label":"U", "x":7.5, "y":2}, {"label":"I", "x":8.5, "y":2}, {"label":"O", "x":9.5, "y":2}, {"label":"P", "x":10.5, "y":2}, {"label":"{", "x":11.5, "y":2}, {"label":"}", "x":12.5, "y":2}, {"label":"7", "x":15, "y":2}, {"label":"8", "x":16, "y":2}, {"label":"9", "x":17, "y":2}, {"label":"+", "x":18, "y":2, "h":2}, {"label":"Caps Lock", "x":0, "y":3, "w":1.75}, {"label":"A", "x":1.75, "y":3}, {"label":"S", "x":2.75, "y":3}, {"label":"D", "x":3.75, "y":3}, {"label":"F", "x":4.75, "y":3}, {"label":"G", "x":5.75, "y":3}, {"label":"H", "x":6.75, "y":3}, {"label":"J", "x":7.75, "y":3}, {"label":"K", "x":8.75, "y":3}, {"label":"L", "x":9.75, "y":3}, {"label":":", "x":10.75, "y":3}, {"label":"@", "x":11.75, "y":3}, {"label":"~", "x":12.75, "y":3}, {"label":"Enter", "x":13.75, "y":2, "w":1.25, "h":2}, {"label":"4", "x":15, "y":3}, {"label":"5", "x":16, "y":3}, {"label":"6", "x":17, "y":3}, {"label":"Shift", "x":0, "y":4, "w":1.25}, {"label":"|", "x":1.25, "y":4}, {"label":"Z", "x":2.25, "y":4}, {"label":"X", "x":3.25, "y":4}, {"label":"C", "x":4.25, "y":4}, {"label":"V", "x":5.25, "y":4}, {"label":"B", "x":6.25, "y":4}, {"label":"N", "x":7.25, "y":4}, {"label":"M", "x":8.25, "y":4}, {"label":"<", "x":9.25, "y":4}, {"label":">", "x":10.25, "y":4}, {"label":"?", "x":11.25, "y":4}, {"label":"Shift", "x":12.25, "y":4, "w":1.75}, {"label":"\u2191", "x":14, "y":4}, {"label":"1", "x":15, "y":4}, {"label":"2", "x":16, "y":4}, {"label":"3", "x":17, "y":4}, {"label":"Enter", "x":18, "y":4, "h":2}, {"label":"Ctrl", "x":0, "y":5, "w":1.25}, {"label":"Win", "x":1.25, "y":5, "w":1.25}, {"label":"Alt", "x":2.5, "y":5, "w":1.25}, {"x":3.75, "y":5, "w":6.25}, {"label":"Alt", "x":10, "y":5, "w":1.5}, {"label":"Ctrl", "x":11.5, "y":5, "w":1.5}, {"label":"\u2190", "x":13, "y":5}, {"label":"\u2193", "x":14, "y":5}, {"label":"\u2192", "x":15, "y":5}, {"label":"0", "x":16, "y":5}, {"label":".", "x":17, "y":5}]
+      "layout": [
        {"label":"Esc", "x":0, "y":0},
        {"label":"F1", "x":1, "y":0},
        {"label":"F2", "x":2, "y":0},
        {"label":"F3", "x":3, "y":0},
        {"label":"F4", "x":4, "y":0},
        {"label":"F5", "x":5, "y":0},
        {"label":"F6", "x":6, "y":0},
        {"label":"F7", "x":7, "y":0},
        {"label":"F8", "x":8, "y":0},
        {"label":"F9", "x":9, "y":0},
        {"label":"F10", "x":10, "y":0},
        {"label":"F11", "x":11, "y":0},
        {"label":"F12", "x":12, "y":0},
        {"label":"Insert", "x":13, "y":0},
        {"label":"Delete", "x":14, "y":0},
        {"label":"Home", "x":15, "y":0},
        {"label":"End", "x":16, "y":0},
        {"label":"PgUp", "x":17, "y":0},
        {"label":"PgDn", "x":18, "y":0},
        {"label":"~", "x":0, "y":1},
        {"label":"!", "x":1, "y":1},
        {"label":"\"", "x":2, "y":1},
        {"label":"\u00a3", "x":3, "y":1},
        {"label":"$", "x":4, "y":1},
        {"label":"%", "x":5, "y":1},
        {"label":"^", "x":6, "y":1},
        {"label":"&", "x":7, "y":1},
        {"label":"*", "x":8, "y":1},
        {"label":"(", "x":9, "y":1},
        {"label":")", "x":10, "y":1},
        {"label":"_", "x":11, "y":1},
        {"label":"+", "x":12, "y":1},
        {"label":"Backspace", "x":13, "y":1, "w":2},
        {"label":"Num Lock", "x":15, "y":1},
        {"label":"/", "x":16, "y":1},
        {"label":"*", "x":17, "y":1},
        {"label":"-", "x":18, "y":1},
        {"label":"Tab", "x":0, "y":2, "w":1.5},
        {"label":"Q", "x":1.5, "y":2},
        {"label":"W", "x":2.5, "y":2},
        {"label":"E", "x":3.5, "y":2},
        {"label":"R", "x":4.5, "y":2},
        {"label":"T", "x":5.5, "y":2},
        {"label":"Y", "x":6.5, "y":2},
        {"label":"U", "x":7.5, "y":2},
        {"label":"I", "x":8.5, "y":2},
        {"label":"O", "x":9.5, "y":2},
        {"label":"P", "x":10.5, "y":2},
        {"label":"{", "x":11.5, "y":2},
        {"label":"}", "x":12.5, "y":2},
        {"label":"7", "x":15, "y":2},
        {"label":"8", "x":16, "y":2},
        {"label":"9", "x":17, "y":2},
        {"label":"Caps Lock", "x":0, "y":3, "w":1.75},
        {"label":"A", "x":1.75, "y":3},
        {"label":"S", "x":2.75, "y":3},
        {"label":"D", "x":3.75, "y":3},
        {"label":"F", "x":4.75, "y":3},
        {"label":"G", "x":5.75, "y":3},
        {"label":"H", "x":6.75, "y":3},
        {"label":"J", "x":7.75, "y":3},
        {"label":"K", "x":8.75, "y":3},
        {"label":"L", "x":9.75, "y":3},
        {"label":":", "x":10.75, "y":3},
        {"label":"@", "x":11.75, "y":3},
        {"label":"~", "x":12.75, "y":3},
        {"label":"Enter", "x":13.75, "y":2, "w":1.25, "h":2},
        {"label":"4", "x":15, "y":3},
        {"label":"5", "x":16, "y":3},
        {"label":"6", "x":17, "y":3},
        {"label":"+", "x":18, "y":2, "h":2},
        {"label":"Shift", "x":0, "y":4, "w":1.25},
        {"label":"|", "x":1.25, "y":4},
        {"label":"Z", "x":2.25, "y":4},
        {"label":"X", "x":3.25, "y":4},
        {"label":"C", "x":4.25, "y":4},
        {"label":"V", "x":5.25, "y":4},
        {"label":"B", "x":6.25, "y":4},
        {"label":"N", "x":7.25, "y":4},
        {"label":"M", "x":8.25, "y":4},
        {"label":"<", "x":9.25, "y":4},
        {"label":">", "x":10.25, "y":4},
        {"label":"?", "x":11.25, "y":4},
        {"label":"Shift", "x":12.25, "y":4, "w":1.75},
        {"label":"\u2191", "x":14, "y":4},
        {"label":"1", "x":15, "y":4},
        {"label":"2", "x":16, "y":4},
        {"label":"3", "x":17, "y":4},
        {"label":"Ctrl", "x":0, "y":5, "w":1.25},
        {"label":"Win", "x":1.25, "y":5, "w":1.25},
        {"label":"Alt", "x":2.5, "y":5, "w":1.25},
        {"x":3.75, "y":5, "w":6.25},
        {"label":"Alt", "x":10, "y":5, "w":1.5},
        {"label":"Ctrl", "x":11.5, "y":5, "w":1.5},
        {"label":"\u2190", "x":13, "y":5},
        {"label":"\u2193", "x":14, "y":5},
        {"label":"\u2192", "x":15, "y":5},
        {"label":"0", "x":16, "y":5},
        {"label":".", "x":17, "y":5},
        {"label":"Enter", "x":18, "y":4, "h":2}
      ]
    }
  }
 }
@@ -79,8 +79,8 @@ MSG_TEST = Testing $(BOLD)$(TEST_NAME)$(NO_COLOR)
 MSG_CHECK_FILESIZE = Checking file size of $(TARGET).hex
 MSG_FILE_TOO_BIG = $(ERROR_COLOR)The firmware is too large!$(NO_COLOR) $(CURRENT_SIZE)/$(MAX_SIZE) ($(OVER_SIZE) bytes over)\n
 MSG_FILE_TOO_SMALL = The firmware is too small! $(CURRENT_SIZE)/$(MAX_SIZE)\n
-MSG_FILE_JUST_RIGHT = The firmware size is fine - $(CURRENT_SIZE)/$(MAX_SIZE) ($(FREE_SIZE) bytes free)\n
+MSG_FILE_JUST_RIGHT = The firmware size is fine - $(CURRENT_SIZE)/$(MAX_SIZE) ($(PERCENT_SIZE)%%, $(FREE_SIZE) bytes free)\n
-MSG_FILE_NEAR_LIMIT = The firmware size is approaching the maximum - $(CURRENT_SIZE)/$(MAX_SIZE) ($(FREE_SIZE) bytes free)\n
+MSG_FILE_NEAR_LIMIT = The firmware size is approaching the maximum - $(CURRENT_SIZE)/$(MAX_SIZE) ($(PERCENT_SIZE)%%, $(FREE_SIZE) bytes free)\n
 MSG_PYTHON_MISSING = $(WARN_COLOR)WARNING:$(NO_COLOR)\n \
 	Python 3 is not installed. It will be required by a future version\n\
 	of qmk_firmware.\n\n\
@@ -3,7 +3,7 @@ RGB_MATRIX_EFFECT(BAND_PINWHEEL_SAT)
 #ifdef RGB_MATRIX_CUSTOM_EFFECT_IMPLS
 static void BAND_PINWHEEL_SAT_math(HSV* hsv, int16_t dx, int16_t dy, uint8_t time) {
-    hsv->s = rgb_matrix_config.sat - time - atan2_8(dy, dx) * 3;
+    hsv->s = scale8(rgb_matrix_config.sat - time - atan2_8(dy, dx) * 3, rgb_matrix_config.sat);
 }
 bool BAND_PINWHEEL_SAT(effect_params_t* params) {
@@ -3,7 +3,7 @@ RGB_MATRIX_EFFECT(BAND_PINWHEEL_VAL)
 #ifdef RGB_MATRIX_CUSTOM_EFFECT_IMPLS
 static void BAND_PINWHEEL_VAL_math(HSV* hsv, int16_t dx, int16_t dy, uint8_t time) {
-    hsv->v = rgb_matrix_config.val - time - atan2_8(dy, dx) * 3;
+    hsv->v = scale8(rgb_matrix_config.val - time - atan2_8(dy, dx) * 3, rgb_matrix_config.val);
 }
 bool BAND_PINWHEEL_VAL(effect_params_t* params) {
@@ -4,7 +4,7 @@ RGB_MATRIX_EFFECT(BAND_SAT)
 static void BAND_SAT_math(HSV* hsv, uint8_t i, uint8_t time) {
    int16_t s = rgb_matrix_config.sat - abs(scale8(g_led_config.point[i].x, 228) + 28 - time) * 8;
-    hsv->s = s < 0 ? 0 : s;
+    hsv->s = scale8(s < 0 ? 0 : s, rgb_matrix_config.sat);
 }
 bool BAND_SAT(effect_params_t* params) {
@@ -3,7 +3,7 @@ RGB_MATRIX_EFFECT(BAND_SPIRAL_SAT)
 #ifdef RGB_MATRIX_CUSTOM_EFFECT_IMPLS
 static void BAND_SPIRAL_SAT_math(HSV* hsv, int16_t dx, int16_t dy, uint8_t dist, uint8_t time) {
-    hsv->s = rgb_matrix_config.sat + dist - time - atan2_8(dy, dx);
+    hsv->s = scale8(rgb_matrix_config.sat + dist - time - atan2_8(dy, dx), rgb_matrix_config.sat);
 }
 bool BAND_SPIRAL_SAT(effect_params_t* params) {
@@ -3,7 +3,7 @@ RGB_MATRIX_EFFECT(BAND_SPIRAL_VAL)
 #ifdef RGB_MATRIX_CUSTOM_EFFECT_IMPLS
 static void BAND_SPIRAL_VAL_math(HSV* hsv, int16_t dx, int16_t dy, uint8_t dist, uint8_t time) {
-    hsv->v = rgb_matrix_config.val + dist - time - atan2_8(dy, dx);
+    hsv->v = scale8(rgb_matrix_config.val + dist - time - atan2_8(dy, dx), rgb_matrix_config.val);
 }
 bool BAND_SPIRAL_VAL(effect_params_t* params) {
@@ -4,7 +4,7 @@ RGB_MATRIX_EFFECT(BAND_VAL)
 static void BAND_VAL_math(HSV* hsv, uint8_t i, uint8_t time) {
    int16_t v = rgb_matrix_config.val - abs(scale8(g_led_config.point[i].x, 228) + 28 - time) * 8;
-    hsv->v = v < 0 ? 0 : v;
+    hsv->v = scale8(v < 0 ? 0 : v, rgb_matrix_config.val);
 }
 bool BAND_VAL(effect_params_t* params) {
@@ -398,6 +398,7 @@ check-size:
 	$(eval CURRENT_SIZE=$(shell if [ -f $(BUILD_DIR)/$(TARGET).hex ]; then $(SIZE) --target=$(FORMAT) $(BUILD_DIR)/$(TARGET).hex | $(AWK) 'NR==2 {print $$4}'; else printf 0; fi))
 	$(eval FREE_SIZE=$(shell expr $(MAX_SIZE) - $(CURRENT_SIZE)))
 	$(eval OVER_SIZE=$(shell expr $(CURRENT_SIZE) - $(MAX_SIZE)))
 	$(eval PERCENT_SIZE=$(shell expr $(CURRENT_SIZE) \* 100 / $(MAX_SIZE)))
 	if [ $(MAX_SIZE) -gt 0 ] && [ $(CURRENT_SIZE) -gt 0 ]; then \
 		$(SILENT) || printf "$(MSG_CHECK_FILESIZE)" | $(AWK_CMD); \
 		if [ $(CURRENT_SIZE) -gt $(MAX_SIZE) ]; then \
@@ -2,7 +2,7 @@
 # Note: This file uses tabs to indent. Please don't mix tabs and spaces.
-GENTOO_WARNING="This script will make a USE change in order to ensure that that QMK works on your system. All changes will be sent to the the file /etc/portage/package.use/qmk_firmware -- please review it, and read Portage's output carefully before installing any packages on your system. You will also need to ensure that your kernel is compiled with support for the keyboard chip that you are using (e.g. enable Arduino for the Pro Micro). Further information can be found on the Gentoo wiki."
+GENTOO_WARNING="This script will make a USE change in order to ensure that that QMK works on your system. All changes will be sent to the the file /etc/portage/package.use/qmkfirmware -- please review it, and read Portage's output carefully before installing any packages on your system. You will also need to ensure that your kernel is compiled with support for the keyboard chip that you are using (e.g. enable Arduino for the Pro Micro). Further information can be found on the Gentoo wiki."
 SLACKWARE_WARNING="You will need the following packages from slackbuilds.org:\n\tarm-binutils\n\tarm-gcc\n\tavr-binutils\n\tavr-gcc\n\tavr-libc\n\tavrdude\n\tdfu-programmer\n\tdfu-util\n\tnewlib\nThese packages will be installed with sudo and sboinstall, so ensure that your user is added to sudoers and that sboinstall is configured."
@@ -29,8 +29,7 @@ NEFM=$(git diff --name-only -n 1 ${TRAVIS_COMMIT_RANGE} | grep -Ev '^(keyboards/
 if [[ $NEFM -gt 0 ]] ; then
 	echo "Essential files modified."
 	git fetch --tags
-	#lasttag=$(git describe --tags $(git rev-list --tags --max-count=10) | grep -Ev '\-' | xargs -I@ git log --format=format:"%ai @%n" -1 @ | sort -V | awk '{print $4}' | tail -1)
+	lasttag=$(git tag --sort=-creatordate --no-column --list '*.*.*' | grep -E -m1 '^[0-9]+\.[0-9]+\.[0-9]+$')
 	lasttag=$(git describe --tags $(git rev-list --tags --max-count=10) | grep -Ev '\-' | sort -V | tail -1)
 	newtag=$(increment_version $lasttag)
 	until git tag $newtag; do
 		newtag=$(increment_version $newtag)
Author	SHA1	Message	Date
skullydazedandnoroadsleft	37d2f6dc2a	Switch version incrementing to the command put together by @noroadsleft. (#6310 ) * Switch version incrementing to the command put together by @noroadsleft. * Update util/travis_compiled_push.sh Co-Authored-By: noroadsleft <[email protected]>	2019-07-11 22:33:25 -07:00
Cody Benderandnoroadsleft	475d2c0c30	[Keyboard] Adding KeyHive Maypad (#6287 ) * added files for KeyHive Maypad * updated maypad files and moved honeycomb inside keyhive dir * fixed file paths, incorporated changes with fauxpark's suggestions, undid honeycomb move * updated with fixes from PR * added new lines to end of honeycomb files to fix compiling * Updated info.json to match the macro name from maypad.h Co-Authored-By: noroadsleft <[email protected]> * reordered layout in info.json Co-Authored-By: noroadsleft <[email protected]> * removed KEYMAP from maypad.h Co-Authored-By: noroadsleft <[email protected]> * removed extraneous keymap files * pulled qmk/master for honeycomb * added ortho_5x4 and keymap cleanup * matched identities in maypad.h * added bootmagic functionality to maypad * changed bootmagic to lite	2019-07-11 13:01:17 -07:00
omkbd	2121de9192	[Keyboard] [runner3680] Fix the number of keys (#6302 ) * Fix the number of keys * add RGBLIGHT_LIMIT_VAL * fix RGBLED_NUM and COLS	2019-07-11 12:27:13 -07:00
fauxparkandnoroadsleft	901edea927	[Keyboard] Fix XD96 info.json (#6309 ) * Fix XD96 info.json * Comma * Another comma Co-Authored-By: noroadsleft <[email protected]>	2019-07-11 12:09:48 -07:00
fauxpark	8e348c427d	Display firmware size percentage (#6307 )	2019-07-11 12:05:13 -07:00
fauxpark	2bbbfc6154	[Keyboard] Update Felix keyboard (#6306 )	2019-07-11 12:04:22 -07:00
fauxparkandKonstantin Đorđević	ecf0612cc8	[Docs] Clarify the rules.mk setup for Unicode (#6286 ) * Clarify the rules.mk setup for Unicode * code point Co-Authored-By: Konstantin Đorđević <[email protected]> * Remove "your" Co-Authored-By: Konstantin Đorđević <[email protected]> * Undo a line change Co-Authored-By: Konstantin Đorđević <[email protected]> * dot the comma Co-Authored-By: Konstantin Đorđević <[email protected]> * Update docs/feature_unicode.md Co-Authored-By: Konstantin Đorđević <[email protected]>	2019-07-11 11:33:55 -07:00
yttyx	676633e1f3	[Keymap] Balance Twelve / Steno Keymap for Planck (#6283 ) * New keymap. Cursor layer does not work. * Refinements to layout over months of use. * Changes following review. * Changes following review.	2019-07-11 11:32:47 -07:00
Napoleon Wulkan	e6420f0bd8	[Keyboard] Add handwired Wulkan keyboard (#6282 ) * added handwired keyboard wulkan * added info.json for qmk configurator * fixed spelling * enum dont need to be assigned to zero * removed cflag from readme * updated rules.mk * removed unneeded rows from config * moved unicode to keymap conf * fix adjust layer and comments for keymap	2019-07-11 11:31:36 -07:00
XScorpion2	3ee062222a	Fixing effects to respect user sat and val levels (#6275 )	2019-07-11 11:29:19 -07:00
Stevan Milic	3dd2905b7b	Add personal KBD67 keymap (#6292 ) * Add kbdfans/kbd67/hotswap:stevanmilic keymap * Change Fn+H, Fn+L to Ctrl+Left, Ctrl+Right * Add keymap comments	2019-07-11 07:37:16 -07:00
zjp	607f6f5c16	Fix typo in Gentoo docstring (#6303 )	2019-07-10 21:22:23 -07:00
noroadsleft	ffff0f03cb	Fix bug in Mechllama G35 info.json (#6294 )	2019-07-10 16:25:54 -07:00
noroadsleft	721b3546f6	QMK Configurator support for NEK Type A (#6295 ) * QMK Configurator support for NEK Type A * Update labels to match default keymap	2019-07-10 16:21:38 -07:00
Drashna Jaelre	05a97482e6	[Keyboard] Enable LTO on Handwired/Promethium to reduce compiled size (#6227 )	2019-07-09 12:59:05 -07:00
`@@ -10,4 +10,4 @@ Make example for this keyboard (after setting up your build environment):`

	`make felix:default`	`make felix:default`

	`See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information.`	`See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).`