Add support for Void Linux systems to the qmk_install.sh script (#5526)

* Add support for Void Linux systems to the qmk_install.sh script

* Fix typos + grammatical edits in comments

* Sort distributions by alphabetical order in linux_install.sh

* Revert previous commit and sort Void packages in alphabetical order

* Fix permissions on `util/linux_install.sh`

docs/driver_installation_zadig.md

@@ -8,10 +8,14 @@ We recommend the use of the [Zadig](https://zadig.akeo.ie/) utility. If you have
 
 ## Installation
 
-Place your keyboard into the bootloader mode, either by hitting the `RESET` keycode (which may be on a different layer), or by pressing the reset switch usually located on the underside of the board. If your keyboard has neither, try holding Escape, or Space+`B`, as you plug it in (see the [Bootmagic](feature_bootmagic.md) docs for more details).
+Put your keyboard into bootloader mode, either by hitting the `RESET` keycode (which may be on a different layer), or by pressing the reset switch that's usually located on the underside of the board. If your keyboard has neither, try holding Escape or Space+`B` as you plug it in (see the [Bootmagic](feature_bootmagic.md) docs for more details). Some boards use [Command](feature_command.md) instead of Bootmagic; in this case, you can enter bootloader mode by hitting Left Shift+Right Shift+`B` or Left Shift+Right Shift+Escape at any point while the keyboard is plugged in.
-Some keyboards may have specific instructions for entering the bootloader, for example the [Bootmagic Lite](feature_bootmagic.md#bootmagic-lite) key (Escape) might be on a different key, such as Left Control. Refer to the board's README if you are unsure.
+Some keyboards may have specific instructions for entering the bootloader. For example, the [Bootmagic Lite](feature_bootmagic.md#bootmagic-lite) key (default: Escape) might be on a different key, e.g. Left Control; or the magic combination for Command (default: Left Shift+Right Shift) might require you to hold something else, e.g. Left Control+Right Control. Refer to the board's README file if you are unsure.
+
+To put a device in bootloader mode with USBaspLoader, tap the `RESET` button while holding down the `BOOT` button.
+Alternatively, hold `BOOT` while inserting the USB cable.
+
+Zadig will automatically detect the bootloader device. You may sometimes need to check **Options → List All Devices**.
 
-Zadig will automatically detect the bootloader device. You may sometimes need to check **Options -> List All Devices**.
  - For keyboards with Atmel AVR MCUs, the bootloader will be named something similar to `ATm32U4DFU`, and have a Vendor ID of `03EB`.
  - USBasp bootloaders will appear as `USBasp`, with a VID/PID of `16C0:05DC`.
  - AVR keyboards flashed with the QMK-DFU bootloader will be named `<keyboard name> Bootloader` and will also have the VID `03EB`.
@@ -19,7 +23,7 @@ Zadig will automatically detect the bootloader device. You may sometimes need to
 
 !> If Zadig lists one or more devices with the `HidUsb` driver, your keyboard is probably not in bootloader mode. The arrow will be colored orange and you will be asked to confirm modifying a system driver. **Do not** proceed if this is the case!
 
-If the arrow appears green, select the driver, and click **Install Driver**. The `libusb-win32` driver will usually work for AVR, and `WinUSB` for ARM, but if you still cannot flash the board, try installing a different driver from the list.
+If the arrow appears green, select the driver, and click **Install Driver**. The `libusb-win32` driver will usually work for AVR, and `WinUSB` for ARM, but if you still cannot flash the board, try installing a different driver from the list. For flashing a USBaspLoader device via command line with msys2, the `libusbk` driver is recommended, otherwise `libusb-win32` will work fine if you are using QMK Toolbox for flashing.
 
 ![Zadig with a bootloader driver correctly installed](https://i.imgur.com/b8VgXzx.png)
 
@@ -39,4 +43,4 @@ Right-click it and hit **Uninstall device**. Make sure to tick **Delete the driv
 
 ![The Device Uninstall dialog, with the "delete driver" checkbox ticked](https://i.imgur.com/aEs2RuA.png)
 
-Click **Action -> Scan for hardware changes**. At this point, you should be able to type again. Double check in Zadig that the keyboard device(s) are using the `HidUsb` driver. If so, you're all done, and your board should be functional again!
+Click **Action → Scan for hardware changes**. At this point, you should be able to type again. Double check in Zadig that the keyboard device(s) are using the `HidUsb` driver. If so, you're all done, and your board should be functional again!

docs/feature_backlight.md

@@ -32,16 +32,18 @@ This feature is distinct from both the [RGB underglow](feature_rgblight.md) and
 
 Hardware PWM is supported according to the following table:
 
-|Backlight Pin|AT90USB64/128|ATmega16/32U4|ATmega16/32U2|ATmega32A|
+|Backlight Pin|AT90USB64/128|ATmega16/32U4|ATmega16/32U2|ATmega32A|ATmega328P|
-|-------------|-------------|-------------|-------------|---------|
+|-------------|-------------|-------------|-------------|---------|----------|
-|`B5`         |Timer 1      |Timer 1      |             |         |
+|`B1`         |             |             |             |         |Timer 1   |
-|`B6`         |Timer 1      |Timer 1      |             |         |
+|`B2`         |             |             |             |         |Timer 1   |
-|`B7`         |Timer 1      |Timer 1      |Timer 1      |         |
+|`B5`         |Timer 1      |Timer 1      |             |         |          |
-|`C4`         |Timer 3      |             |             |         |
+|`B6`         |Timer 1      |Timer 1      |             |         |          |
-|`C5`         |Timer 3      |             |Timer 1      |         |
+|`B7`         |Timer 1      |Timer 1      |Timer 1      |         |          |
-|`C6`         |Timer 3      |Timer 3      |Timer 1      |         |
+|`C4`         |Timer 3      |             |             |         |          |
-|`D4`         |             |             |             |Timer 1  |
+|`C5`         |Timer 3      |             |Timer 1      |         |          |
-|`D5`         |             |             |             |Timer 1  |
+|`C6`         |Timer 3      |Timer 3      |Timer 1      |         |          |
+|`D4`         |             |             |             |Timer 1  |          |
+|`D5`         |             |             |             |Timer 1  |          |
 
 All other pins will use software PWM. If the [Audio](feature_audio.md) feature is disabled or only using one timer, the backlight PWM can be triggered by a hardware timer:
 

docs/flashing.md

@@ -10,11 +10,17 @@ Atmel's DFU bootloader comes on all atmega32u4 chips by default, and is used by
 
 To ensure compatibility with the DFU bootloader, make sure this block is present your `rules.mk` (optionally with `lufa-dfu` or `qmk-dfu` instead):
 
-    # Bootloader
+```make
-    #     This definition is optional, and if your keyboard supports multiple bootloaders of
+# Bootloader selection
-    #     different sizes, comment this out, and the correct address will be loaded
+#   Teensy       halfkay
-    #     automatically (+60). See bootloader.mk for all options.
+#   Pro Micro    caterina
-    BOOTLOADER = atmel-dfu
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = atmel-dfu
+```
 
 Compatible flashers:
 
@@ -64,11 +70,17 @@ Arduino boards and their clones use the [Caterina bootloader](https://github.com
 
 To ensure compatibility with the Caterina bootloader, make sure this block is present your `rules.mk`:
 
-    # Bootloader
+```make
-    #     This definition is optional, and if your keyboard supports multiple bootloaders of
+# Bootloader selection
-    #     different sizes, comment this out, and the correct address will be loaded
+#   Teensy       halfkay
-    #     automatically (+60). See bootloader.mk for all options.
+#   Pro Micro    caterina
-    BOOTLOADER = caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = caterina
+```
 
 Compatible flashers:
 
@@ -100,11 +112,17 @@ Halfkay is a super-slim protocol developed by PJRC that uses HID, and come on al
 
 To ensure compatibility with the Halfkay bootloader, make sure this block is present your `rules.mk`:
 
-    # Bootloader
+```make
-    #     This definition is optional, and if your keyboard supports multiple bootloaders of
+# Bootloader selection
-    #     different sizes, comment this out, and the correct address will be loaded
+#   Teensy       halfkay
-    #     automatically (+60). See bootloader.mk for all options.
+#   Pro Micro    caterina
-    BOOTLOADER = halfkay
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = halfkay
+```
 
 Compatible flashers:
 
@@ -125,11 +143,17 @@ USBasploader is a bootloader developed by matrixstorm. It is used in some non-US
 
 To ensure compatibility with the USBasploader bootloader, make sure this block is present in your `rules.mk`:
 
-    # Bootloader
+```make
-    #     This definition is optional, and if your keyboard supports multiple bootloaders of
+# Bootloader selection
-    #     different sizes, comment this out, and the correct address will be loaded
+#   Teensy       halfkay
-    #     automatically (+60). See bootloader.mk for all options.
+#   Pro Micro    caterina
-    BOOTLOADER = USBasp
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = USBasp
+```
 
 Compatible flashers:
 
@@ -150,11 +174,17 @@ BootloadHID is a USB bootloader for AVR microcontrollers. The uploader tool requ
 
 To ensure compatibility with the bootloadHID bootloader, make sure this block is present your `rules.mk`:
 
-    # Bootloader
+```make
-    #     This definition is optional, and if your keyboard supports multiple bootloaders of
+# Bootloader selection
-    #     different sizes, comment this out, and the correct address will be loaded
+#   Teensy       halfkay
-    #     automatically (+60). See bootloader.mk for all options.
+#   Pro Micro    caterina
-    BOOTLOADER = bootloadHID
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = bootloadHID
+```
 
 Compatible flashers:
 

keyboards/2key2crawl/rules.mk

@@ -1,18 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-
 # Build Options
 #   comment out to disable the options.
 #

keyboards/alps64/rules.mk

@@ -1,13 +1,14 @@
 # MCU name
 MCU = atmega32u2
 
-# Boot Section Size in *bytes*
+# Bootloader selection
-#   Teensy halfKay   512
+#   Teensy       halfkay
-#   Teensy++ halfKay 1024
+#   Pro Micro    caterina
-#   Atmel DFU loader 4096
+#   Atmel DFU    atmel-dfu
-#   LUFA bootloader  4096
+#   LUFA DFU     lufa-dfu
-#   USBaspLoader     2048
+#   QMK DFU      qmk-dfu
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
 # Build Options

keyboards/ares/rules.mk

@@ -15,18 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_SUSPEND_POWER_DOWN = yes
+#   Teensy       halfkay
-
+#   Pro Micro    caterina
-# processor frequency
+#   Atmel DFU    atmel-dfu
-F_CPU = 12000000
+#   LUFA DFU     lufa-dfu
-
+#   QMK DFU      qmk-dfu
-# Bootloader
+#   ATmega32A    bootloadHID
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#   ATmega328P   USBasp
-#     different sizes, comment this out, and the correct address will be loaded 
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -38,11 +35,7 @@ COMMAND_ENABLE = yes
 BACKLIGHT_ENABLE = no
 RGBLIGHT_ENABLE = no
 RGBLIGHT_CUSTOM_DRIVER = yes
-NO_UART = yes
 
 OPT_DEFS = -DDEBUG_LEVEL=0
 
 SRC += i2c_master.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/bfake/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded 
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -45,6 +41,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/bigseries/rules.mk

@@ -1,45 +1,15 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 
 # Build Options
 #   comment out to disable the options.

keyboards/bpiphany/frosty_flake/rules.mk

@@ -1,51 +1,15 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 
 # Build Options
 #   change yes to no to disable

keyboards/bpiphany/kitten_paw/rules.mk

@@ -1,51 +1,15 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-	OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 
 # Build Options
 #   change yes to no to disable

keyboards/bpiphany/pegasushoof/rules.mk

@@ -1,42 +1,15 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-BOOTLOADER=atmel-dfu
 
 # Build Options
 #   change yes to no to disable

keyboards/bpiphany/tiger_lily/rules.mk

@@ -1,51 +1,15 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 
 # Build Options
 #   change yes to no to disable

keyboards/bpiphany/unloved_bastard/rules.mk

@@ -1,51 +1,15 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 
 # Build Options
 #   change yes to no to disable

keyboards/canoe/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -45,6 +41,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/clueboard/2x1800/rules.mk

@@ -1,11 +1,15 @@
-# MCU details
+# MCU name
 MCU = at90usb1286
-F_CPU = 16000000
-ARCH = AVR8
-F_USB = $(F_CPU)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-OPT_DEFS += -DBOOTLOADER_SIZE=1024
 
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = halfkay
 
 # Build Options
 BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)

keyboards/converter/modelm101/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = halfkay
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-#OPT_DEFS += -DBOOTLOADER_SIZE=1024
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/coseyfannitutti/discipad/config.h

@@ -0,0 +1,249 @@
+/*
+Copyright 2019 coseyfannitutti
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x1769
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    coseyfannitutti
+#define PRODUCT         DISCIPAD
+#define DESCRIPTION     17-key numpad assembled with only through hole components
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 4
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+ */
+
+/* A Custom matrix.c is used to poll the port expander C6 shows that the pins are hardwired there */
+#define MATRIX_ROW_PINS { B1, B0, D7, D6, D4 }
+#define MATRIX_COL_PINS { C0, C1, C2, C3 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+#define NO_UART 1
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+// #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCE 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration
+#define BOOTMAGIC_LITE_ROW 0
+#define BOOTMAGIC_LITE_COLUMN 0
+*/

keyboards/coseyfannitutti/discipad/discipad.c

@@ -0,0 +1,24 @@
+/* Copyright 2019 coseyfannitutti
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "discipad.h"
+
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}

keyboards/coseyfannitutti/discipad/discipad.h

@@ -0,0 +1,43 @@
+/* Copyright 2019 coseyfannitutti
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+#define _x_ KC_NO
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT_numpad_5x4( \
+  K00, K01, K02, K03, \
+  K10, K11, K12,      \
+  K20, K21, K22, K23, \
+  K30, K31, K32,      \
+  K40,      K42, K43  \
+) { \
+{ K00, K01, K02, K03, }, \
+{ K10, K11, K12, _x_, }, \
+{ K20, K21, K22, K23, }, \
+{ K30, K31, K32, _x_, }, \
+{ K40, _x_, K42, K43, }, \
+}
+

keyboards/coseyfannitutti/discipad/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "DISCIPAD", 
+    "url": "https://github.com/coseyfannitutti/discipad", 
+    "maintainer": "coseyfannitutti", 
+    "width": 4, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT_numpad_5x4": {
+            "layout": [{"label":"Num Lock", "x":0, "y":0}, {"label":"/", "x":1, "y":0}, {"label":"*", "x":2, "y":0}, {"label":"-", "x":3, "y":0}, {"label":"7", "x":0, "y":1}, {"label":"8", "x":1, "y":1}, {"label":"9", "x":2, "y":1}, {"label":"4", "x":0, "y":2}, {"label":"5", "x":1, "y":2}, {"label":"6", "x":2, "y":2}, {"label":"+", "x":3, "y":1, "h":2}, {"label":"1", "x":0, "y":3}, {"label":"2", "x":1, "y":3}, {"label":"3", "x":2, "y":3}, {"label":"0", "x":0, "y":4, "w":2}, {"label":".", "x":2, "y":4}, {"label":"Enter", "x":3, "y":3, "h":2}]
+        }
+    }
+}

keyboards/coseyfannitutti/discipad/keymaps/default/keymap.c

@@ -0,0 +1,27 @@
+/* Copyright 2019 COSEYFANNITUTTI
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+#define _BL 0
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_BL] = LAYOUT_numpad_5x4(
+      KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, 
+      KC_P7,   KC_P8,   KC_P9,            
+      KC_P4,   KC_P5,   KC_P6,   KC_PPLS, 
+      KC_P1,   KC_P2,   KC_P3,            
+      KC_P0,   KC_PDOT,          KC_PENT  )
+};

keyboards/coseyfannitutti/discipad/readme.md

@@ -0,0 +1,15 @@
+# DISCIPAD
+
+![discipline](https://i.imgur.com/3Coydx7.jpg)
+
+A 17-key numpad that can be assembled with only through hole components, including usb type-c
+
+Keyboard Maintainer: [coseyfannitutti](https://github.com/coseyfannitutti)  
+Hardware Supported: DISCIPAD, atmega328p  
+Hardware Availability: [cftkb.com](http://www.cftkb.com), [GitHub](https://github.com/coseyfannitutti/discipad)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make coseyfannitutti/discipad:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/coseyfannitutti/discipad/rules.mk

@@ -0,0 +1,34 @@
+# MCU name
+MCU = atmega328p
+
+# Bootloader selection
+BOOTLOADER = USBasp
+
+# Flash program via avrdude, but default command is not suitable.
+# You can use coseyfannitutti/discipad:default:program
+PROGRAM_CMD = avrdude -c usbasp -p m328p -U flash:w:$(BUILD_DIR)/$(TARGET).hex
+
+# disable debug code
+OPT_DEFS = -DDEBUG_LEVEL=0
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)

keyboards/coseyfannitutti/discipad/usbconfig.h

@@ -0,0 +1,397 @@
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
+ */
+
+#ifndef __usbconfig_h_included__
+#define __usbconfig_h_included__
+
+#include "config.h"
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME      D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT      3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT       2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC       0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME   D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT          4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT    1
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3   1
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER              3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN           USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT          0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE      0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL      1
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED         0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+// max power draw with maxed white underglow measured at 120 mA (peaks)
+#define USB_CFG_MAX_BUS_POWER           100
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE      1
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ       0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL        0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS          0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK()              hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF                   0
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ *     in      YL, TCNT0
+ *     sts     timer0Snapshot, YL
+ *     endm
+ * #endif
+ * #define USB_SOF_HOOK                    myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING     0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define USB_CFG_VENDOR_ID       (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_ID       (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION  0x01, 0x00
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME     'c','o','s','e','y','f','a','n','n','i','t','u','t','t','i'
+#define USB_CFG_VENDOR_NAME_LEN 15
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME     'D','I','S','C','I','P','A','D'
+#define USB_CFG_DEVICE_NAME_LEN 8
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+#define USB_CFG_SERIAL_NUMBER   '0'
+#define USB_CFG_SERIAL_NUMBER_LEN   1
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS        0
+#define USB_CFG_DEVICE_SUBCLASS     0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS     3   /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS  1   /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL  1   /* Keyboard */
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ *     you want RAM pointers.
+ *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ *     in static memory is in RAM, not in flash memory.
+ *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ *     the driver must know the descriptor's length. The descriptor itself is
+ *     found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ *   char usbDescriptorDevice[];
+ *   char usbDescriptorConfiguration[];
+ *   char usbDescriptorHidReport[];
+ *   char usbDescriptorString0[];
+ *   int usbDescriptorStringVendor[];
+ *   int usbDescriptorStringDevice[];
+ *   int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ *   USB_CFG_DESCR_PROPS_DEVICE
+ *   USB_CFG_DESCR_PROPS_CONFIGURATION
+ *   USB_CFG_DESCR_PROPS_STRINGS
+ *   USB_CFG_DESCR_PROPS_STRING_0
+ *   USB_CFG_DESCR_PROPS_STRING_VENDOR
+ *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ *   USB_CFG_DESCR_PROPS_HID
+ *   USB_CFG_DESCR_PROPS_HID_REPORT
+ *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int  serialNumberDescriptor[] = {
+ *     USB_STRING_DESCRIPTOR_HEADER(6),
+ *     'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE                  0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION           USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
+#define USB_CFG_DESCR_PROPS_STRINGS                 0
+#define USB_CFG_DESCR_PROPS_STRING_0                0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
+#define USB_CFG_DESCR_PROPS_HID                     USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID                     0
+#define USB_CFG_DESCR_PROPS_HID_REPORT              USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID_REPORT              0
+#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG            MCUCR */
+/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         GIMSK */
+/* #define USB_INTR_ENABLE_BIT     INT0 */
+/* #define USB_INTR_PENDING        GIFR */
+/* #define USB_INTR_PENDING_BIT    INTF0 */
+/* #define USB_INTR_VECTOR         INT0_vect */
+
+/* Set INT1 for D- falling edge to count SOF */
+/* #define USB_INTR_CFG            EICRA */
+// #define USB_INTR_CFG_SET        ((1 << ISC11) | (0 << ISC10))
+// /* #define USB_INTR_CFG_CLR        0 */
+// /* #define USB_INTR_ENABLE         EIMSK */
+// #define USB_INTR_ENABLE_BIT     INT1
+// /* #define USB_INTR_PENDING        EIFR */
+// #define USB_INTR_PENDING_BIT    INTF1
+// #define USB_INTR_VECTOR         INT1_vect
+
+#endif /* __usbconfig_h_included__ */

keyboards/coseyfannitutti/discipline/rules.mk

@@ -1,61 +1,19 @@
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# Processor frequency.
+# Processor frequency
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
 F_CPU = 16000000
 
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
-#
+#   ATmega328P   USBasp
-# This uses usbaspbootloader
 BOOTLOADER = USBasp
 
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-
 # Flash program via avrdude, but default command is not suitable.
 # You can use plaid:default:program
 PROGRAM_CMD = avrdude -c usbasp -p m32 -U flash:w:$(BUILD_DIR)/$(TARGET).hex
@@ -84,8 +42,4 @@ AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 
-# unsupported features for now
-NO_UART = yes
-NO_SUSPEND_POWER_DOWN = yes
-
 LAYOUTS = 65_ansi

keyboards/donutcables/budget96/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -44,6 +40,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 
 # custom matrix setup
 SRC = i2c_master.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/donutcables/scrabblepad/rules.mk

@@ -1,51 +1,15 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = halfkay
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 
 # Build Options
 #   change yes to no to disable

keyboards/dz60/keymaps/ottodokto/config.h

@@ -0,0 +1,13 @@
+/*---defines-------------------------------------------- */
+#define TAPPING_TOGGLE 2 // toggle on layer on two taps.
+
+/*---RGB settings-------------------------------------------- */
+#undef  RGBLIGHT_HUE_STEP
+#undef  RGBLIGHT_SAT_STEP
+#undef  RGBLIGHT_VAL_STEP
+#undef  RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL
+
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17
+#define RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL 200

keyboards/dz60/keymaps/ottodokto/keymap.c

@@ -0,0 +1,44 @@
+/* 
+   Last updated: 3 Aug 2019
+   DZ60 Layout by ottodokto
+
+   This layout is a modification of the 60 tsangan hhkb layout, 
+   with an additional layer to update the arrow keys and 
+   */
+
+#include QMK_KEYBOARD_H
+
+/*---Layers-------------------------------------------- */
+#define _base 0 // default, tsangan layout with split backspace
+#define _func 1 // media controls and reset buttons
+
+/*---defines-------------------------------------------- */
+#define KC_CTOG LT(_func, KC_CAPS)
+#define KC_TTAP TT(_func)
+
+#define RGB_STA RGB_M_P		// rgb static
+#define RGB_BRE RGB_M_B 	// rgb breathe
+#define RGB_RAI RGB_M_R 	// rgb rainbow
+#define RGB_SWI RGB_M_SW 	// rgb swirl
+#define RGB_SNA RGB_M_SN	// rgb snake
+#define RGB_KNI RGB_M_K 	// rgb knight
+#define RGB_GRA RGB_M_G 	// rgb gradient
+
+
+/*---Layout-------------------------------------------- */
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    [_base] = LAYOUT_60_tsangan_hhkb(
+		KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSLS, KC_GRV, \
+		KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSPC, \
+		KC_CTOG, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT, \
+		KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT, KC_TTAP, \
+		KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, KC_RGUI, KC_RCTL 
+	),
+    [_func] = LAYOUT_60_tsangan_hhkb(
+		RGB_TOG, KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  _______, RESET, \
+		_______, KC_HOME, KC_UP,   KC_END,  KC_PGUP, _______, RGB_SPI, RGB_HUD, RGB_VAI, RGB_HUI, KC_MUTE, KC_VOLD, KC_VOLU, KC_DEL, \
+		_______, KC_LEFT, KC_DOWN, KC_RGHT, KC_PGDN, _______, RGB_SPD, RGB_SAD, RGB_VAD, RGB_SAI, KC_BRID, KC_BRIU, _______, \
+		_______, RGB_STA, RGB_BRE, RGB_RAI, RGB_SWI, RGB_SNA, RGB_KNI, RGB_GRA, VLK_TOG, _______, _______, _______, _______, \
+		_______, _______, _______,                            _______,                            _______, _______, _______
+    )
+};

keyboards/dz60/keymaps/ottodokto/rules.mk

@@ -0,0 +1 @@
+VELOCIKEY_ENABLE = yes

keyboards/eve/meteor/rules.mk

@@ -16,10 +16,14 @@
 # MCU name
 MCU = atmega32a
 
-# Bootloader
+# Bootloader selection
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#   Teensy       halfkay
-#     different sizes, comment this out, and the correct address will be loaded
+#   Pro Micro    caterina
-#     automatically (+60). See bootloader.mk for all options.
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = bootloadHID
 
 # build options

keyboards/exclusive/e6v2/le_bmc/rules.mk

@@ -1,46 +1,5 @@
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
-
-NO_UART = yes
-NO_SUSPEND_POWER_DOWN = yes
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 12000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-# ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-# F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS = -DDEBUG_LEVEL=0
-
 
 # Bootloader selection
 #   Teensy       halfkay
@@ -48,20 +7,10 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = bootloadHID
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #
@@ -84,6 +33,5 @@ AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 
+OPT_DEFS = -DDEBUG_LEVEL=0
 SRC += i2c_master.c
-
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/exclusive/e6v2/oe_bmc/rules.mk

@@ -1,46 +1,5 @@
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
-
-NO_UART = yes
-NO_SUSPEND_POWER_DOWN = yes
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 12000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-# ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-# F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS = -DDEBUG_LEVEL=0
-
 
 # Bootloader selection
 #   Teensy       halfkay
@@ -48,20 +7,10 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = bootloadHID
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #
@@ -84,6 +33,5 @@ AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 
+OPT_DEFS = -DDEBUG_LEVEL=0
 SRC += i2c_master.c
-
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/facew/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -45,7 +41,4 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 SRC = i2c_master.c
 
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
-
 LAYOUTS = 60_ansi

keyboards/ft/mars80/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -44,7 +40,4 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 
 SRC += i2c_master.c
 
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
-
 LAYOUTS = tkl_ansi tkl_iso

keyboards/gingham/rules.mk

@@ -10,9 +10,8 @@ MCU = atmega328p
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
-#
+#   ATmega328P   USBasp
-# This uses usbaspbootloader
 BOOTLOADER = USBasp
 
 # Flash program via avrdude, but default command is not suitable.

keyboards/gray_studio/hb85/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -43,6 +39,3 @@ RGBLIGHT_CUSTOM_DRIVER = yes
 OPT_DEFS = -DDEBUG_LEVEL=0
 
 SRC += i2c_master.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/handwired/108key_trackpoint/rules.mk

@@ -1,62 +1,16 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = halfkay
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/handwired/6macro/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/handwired/aek64/rules.mk

@@ -1,17 +1,15 @@
-# Target file name (without extension).
-
-# project specific files
-
 # MCU name
 MCU = at90usb1286
 
-# Boot Section Size in *bytes*
+# Bootloader selection
-#   Teensy halfKay   512
+#   Teensy       halfkay
-#   Teensy++ halfKay 1024
+#   Pro Micro    caterina
-#   Atmel DFU loader 4096
+#   Atmel DFU    atmel-dfu
-#   LUFA bootloader  4096
+#   LUFA DFU     lufa-dfu
-#   USBaspLoader     2048
+#   QMK DFU      qmk-dfu
-BOOTLOADER = halfKay
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = halfkay
 
 # Build Options
 #   change to no to disable the options.

keyboards/handwired/daishi/rules.mk

@@ -1,49 +1,14 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
 BOOTLOADER = atmel-dfu
 
 # QMK Build Options
@@ -63,4 +28,4 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-ENCODER_ENABLE = yes		# Add rotary encoder support
+ENCODER_ENABLE = yes		# Add rotary encoder support

keyboards/handwired/datahand/rules.mk

@@ -1,44 +1,14 @@
-# Project-specific includes
-SRC = matrix.c
-
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 BOOTLOADER = halfkay
 
 # Build Options
@@ -57,3 +27,6 @@ CUSTOM_MATRIX     = yes  # We definitely have a nonstandard matrix
 
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+
+# Project specific files
+SRC = matrix.c

keyboards/handwired/downbubble/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/handwired/hacked_motospeed/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = halfkay
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=1024
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/handwired/hnah40/rules.mk

@@ -1,7 +1,15 @@
 # MCU name
 MCU = atmega328p
 
-BOOTLOADER = bootloadHID
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = USBasp
 
 # Flash program via avrdude, but default command is not suitable.
 # You can use hnah40:default:program

keyboards/handwired/ibm122m/rules.mk

@@ -1,51 +1,15 @@
 # MCU name
 MCU = at90usb1286
-BOOTLOADER = halfKay
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
 
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = halfkay
 
 # Build Options
 #   change yes to no to disable

keyboards/handwired/magicforce61/rules.mk

@@ -1,52 +1,15 @@
-
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = halfkay
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=1024
-
 
 # Build Options
 #   change yes to no to disable

keyboards/handwired/ms_sculpt_mobile/rules.mk

@@ -1,37 +1,27 @@
-
-## Project specific files
-SRC=  babblePaste.c
-
-
 ifdef ASTAR
-  CFLAGS=-D ASTAR
+    MCU = atmega32u4
- MCU = atmega32u4
+    CFLAGS = -D ASTAR
- SCULPT_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done ; \
+    USB = /dev/cu.usbmodem14141
-		 avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
+    SCULPT_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done ; avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
-
 else
- MCU = at90usb1286
+    MCU = at90usb1286
- SCULPT_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
+    SCULPT_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
 endif
 
-F_CPU = 16000000
+# Bootloader selection
-ARCH = AVR8
+#   Teensy       halfkay
-F_USB = $(F_CPU)
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# Bootloader
+#   LUFA DFU     lufa-dfu
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#   QMK DFU      qmk-dfu
-#     different sizes, comment this out, and the correct address will be loaded 
+#   ATmega32A    bootloadHID
-#     automatically (+60). See bootloader.mk for all options.
+#   ATmega328P   USBasp
 ifdef ASTAR
-  BOOTLOADER = caterina
+    BOOTLOADER = caterina
 else
-  BOOTLOADER = atmel-dfu
+    BOOTLOADER = atmel-dfu
 endif
 
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-#
 BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
 MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
 EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
@@ -47,10 +37,5 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 
-
+# Project specific files
-USB = /dev/cu.usbmodem14141
+SRC = babblePaste.c
-
- 
-
-# upload: build
-# 	$(SCULPT_UPLOAD_COMMAND)

keyboards/handwired/onekey/teensy_2pp/rules.mk

@@ -1,58 +1,12 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = halfkay
-
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096

keyboards/idb_60/rules.mk

@@ -1,52 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
 BOOTLOADER = atmel-dfu
 
-
 # Build Options
 #   comment out to disable the options.
 #
@@ -62,4 +26,4 @@ NKRO_ENABLE = yes			# USB Nkey Rollover - if this doesn't work, see here: https:
 # BACKLIGHT_ENABLE = yes	# Enable keyboard backlight functionality
 # MIDI_ENABLE = YES			# MIDI controls
 # UNICODE_ENABLE = YES		# Unicode
-# BLUETOOTH_ENABLE = yes	# Enable Bluetooth with the Adafruit EZ-Key HID
+# BLUETOOTH_ENABLE = yes	# Enable Bluetooth with the Adafruit EZ-Key HID

keyboards/illuminati/is0/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/jc65/v32a/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -45,6 +41,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/jj40/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # Build Options
@@ -54,7 +50,4 @@ HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 
 SRC += i2c_master.c
 
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
-
 LAYOUTS = ortho_4x12 planck_mit

keyboards/jj4x4/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # Build Options
@@ -54,7 +50,4 @@ HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 
 SRC += i2c_master.c
 
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
-
 LAYOUTS = ortho_4x4

keyboards/jj50/keymaps/archetype/rules.mk

@@ -16,19 +16,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -59,7 +55,4 @@ SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c backlight.c
 
-# programming options
-PROGRAM_CMD = ./keyboards/ps2avrGB/program $(TARGET).hex
-
 LAYOUTS = ortho_5x12

keyboards/jj50/rules.mk

@@ -16,14 +16,6 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
-
-# unsupported features for now
-NO_UART = yes
-NO_SUSPEND_POWER_DOWN = yes
-
-# processor frequency
-F_CPU = 12000000
 
 # Bootloader selection
 #   Teensy       halfkay
@@ -31,7 +23,8 @@ F_CPU = 12000000
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = bootloadHID
 
 # build options
@@ -60,7 +53,4 @@ SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c backlight.c
 
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
-
 LAYOUTS = ortho_5x12

keyboards/kbdfans/kbdpad/mk1/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -43,6 +39,3 @@ RGBLIGHT_CUSTOM_DRIVER = no
 OPT_DEFS = -DDEBUG_LEVEL=0
 
 QUANTUM_LIB_SRC = i2c_master.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/kbdfans/kbdpad_mk2/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/kinesis/rules.mk

@@ -1,56 +1,15 @@
-
-## Project specific files
-
-SRC=  matrix.c 
-
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = halfkay
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 2048
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=2048
-
 
 # Build Options
 #   change yes to no to disable
@@ -72,3 +31,6 @@ AUDIO_ENABLE = no # Audio output should be port E6, current quantum library hard
 CUSTOM_MATRIX=yes # need to do our own thing with the matrix
 
 DEFAULT_FOLDER = kinesis/alvicstep
+
+# Project specific files
+SRC = matrix.c

keyboards/lfkeyboards/lfk78/rules.mk

@@ -7,14 +7,12 @@ LFK_REV = J
 
 ifeq ($(LFK_REV), B)
     MCU = atmega32u4
-    OPT_DEFS += -DBOOTLOADER_SIZE=4096
 else ifeq ($(LFK_REV), J)
     MCU = at90usb646
-    OPT_DEFS += -DBOOTLOADER_SIZE=4096
 else
     MCU = at90usb1286
-    OPT_DEFS += -DBOOTLOADER_SIZE=8192
 endif
+BOOTLOADER = atmel-dfu
 OPT_DEFS += -DLFK_REV_$(LFK_REV)
 OPT_DEFS += -DLFK_REV_STRING=\"Rev$(LFK_REV)\"
 

keyboards/lfkeyboards/lfk87/rules.mk

@@ -7,12 +7,11 @@
 LFK_REV = C
 
 ifeq ($(LFK_REV), A)
-	MCU = at90usb1286
+    MCU = at90usb1286
-	OPT_DEFS += -DBOOTLOADER_SIZE=8192
 else
-	MCU = at90usb646
+    MCU = at90usb646
-	OPT_DEFS += -DBOOTLOADER_SIZE=4096
 endif
+BOOTLOADER = atmel-dfu
 OPT_DEFS += -DLFK_TKL_REV_$(LFK_REV)
 
 # Extra source files for IS3731 lighting

keyboards/lfkeyboards/mini1800/rules.mk

@@ -8,12 +8,11 @@
 LFK_REV = C
 
 ifeq ($(LFK_REV), A)
-	MCU = at90usb1286
+    MCU = at90usb1286
-	OPT_DEFS += -DBOOTLOADER_SIZE=8192
 else
-	MCU = at90usb646
+    MCU = at90usb646
-	OPT_DEFS += -DBOOTLOADER_SIZE=4096
 endif
+BOOTLOADER = atmel-dfu
 OPT_DEFS += -DLFK_TKL_REV_$(LFK_REV)
 
 # Extra source files for IS3731 lighting

keyboards/lfkeyboards/smk65/rules.mk

@@ -1,5 +1,15 @@
+# MCU name
 MCU = at90usb646
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = atmel-dfu
 
 # Extra source files for IS3731 lighting
 SRC = TWIlib.c issi.c lighting.c

keyboards/m0lly/rules.mk

@@ -1,54 +1,16 @@
-
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/mechmini/v1/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = atmel-dfu
 
 # build options
@@ -45,6 +41,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/mehkee96/rules.mk

@@ -1,18 +1,16 @@
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# Processor frequency.
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
 BOOTLOADER = bootloadHID
 
-
 # Build Options
 #   comment out to disable the options.
 #
@@ -30,6 +28,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/meme/rules.mk

@@ -1,51 +1,15 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 
 # Build Options
 #   change yes to no to disable

keyboards/mt40/rules.mk

@@ -1,18 +1,14 @@
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -37,8 +33,5 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c
 
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
-
 LAYOUTS = planck_mit
 LAYOUTS_HAS_RGB = no

keyboards/novelpad/rules.mk

@@ -1,17 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
 # Build Options
 #   comment out to disable the options.
 #

keyboards/omnikey_blackheart/rules.mk

@@ -1,45 +1,15 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = halfkay
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
 
 # Build Options
 #   comment out to disable the options.
@@ -53,4 +23,4 @@ SLEEP_LED_ENABLE ?= no  # Breathing sleep LED during USB suspend
 NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
 BACKLIGHT_ENABLE ?= no  # Enable keyboard backlight functionality
 AUDIO_ENABLE ?= no
-RGBLIGHT_ENABLE ?= no
+RGBLIGHT_ENABLE ?= no

keyboards/omnikeyish/rules.mk

@@ -1,55 +1,16 @@
-# keyboard specific files
-SRC += dynamic_macro.c
-
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = halfkay
 
-
 # Build Options
 #   comment out to disable the options.
 #
@@ -62,4 +23,7 @@ SLEEP_LED_ENABLE = no 	# Breathing sleep LED during USB suspend
 NKRO_ENABLE = yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
 BACKLIGHT_ENABLE = no  	# Enable keyboard backlight functionality
 AUDIO_ENABLE = no
-RGBLIGHT_ENABLE = no
+RGBLIGHT_ENABLE = no
+
+# Project specific files
+SRC += dynamic_macro.c

keyboards/panc60/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -45,7 +41,4 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 SRC = i2c_master.c
 
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
-
 LAYOUTS = 60_ansi 60_hhkb

keyboards/pearl/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -44,6 +40,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 
 # custom matrix setup
 SRC = i2c_master.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/plaid/rules.mk

@@ -7,21 +7,9 @@ MCU = atmega328p
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
-#
+#   ATmega328P   USBasp
-# This uses usbaspbootloader
+BOOTLOADER = USBasp
-# BOOTLOADER = atmel-dfu
-
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-OPT_DEFS += -DBOOTLOADER_SIZE=2048
 
 # Flash program via avrdude, but default command is not suitable.
 # You can use plaid:default:program

keyboards/planck/light/rules.mk

@@ -1,15 +1,16 @@
 # MCU name
 MCU = at90usb1286
 
-# Bootloader
+# Bootloader selection
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#   Teensy       halfkay
-#     different sizes, comment this out, and the correct address will be loaded
+#   Pro Micro    caterina
-#     automatically (+60). See bootloader.mk for all options.
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # Build Options
 #   change to "no" to disable the options, or define them in the Makefile in
 #   the appropriate keymap folder that will get included automatically

keyboards/primekb/prime_m/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/primekb/prime_o/rules.mk

@@ -1,63 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/singa/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -43,6 +39,3 @@ RGBLIGHT_CUSTOM_DRIVER = yes
 OPT_DEFS = -DDEBUG_LEVEL=0
 
 SRC = i2c_master.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/sixkeyboard/rules.mk

@@ -3,15 +3,15 @@ SRC = matrix.c
 # MCU name
 MCU = atmega16u2
 
-
+# Bootloader selection
-# Boot Section Size in *bytes*
+#   Teensy       halfkay
-#   Teensy halfKay   512
+#   Pro Micro    caterina
-#   Teensy++ halfKay 1024
+#   Atmel DFU    atmel-dfu
-#   Atmel DFU loader 4096
+#   LUFA DFU     lufa-dfu
-#   LUFA bootloader  4096
+#   QMK DFU      qmk-dfu
-#   USBaspLoader     2048
+#   ATmega32A    bootloadHID
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+#   ATmega328P   USBasp
-
+BOOTLOADER = atmel-dfu
 
 # Build Options
 #   comment out to disable the options.

keyboards/skog/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -50,6 +46,3 @@ SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c backlight.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/staryu/rules.mk

@@ -1,61 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = lufa-dfu
 
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-#   Teensy halfKay      512
-#   Teensy++ halfKay    1024
-#   Atmel DFU loader    4096
-#   LUFA bootloader     4096
-#   USBaspLoader        2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
 # Build Options
 #   comment out to disable the options.
 #

keyboards/subatomic/rules.mk

@@ -1,51 +1,15 @@
-
-
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=8192
 
 # Build Options
 #   change to "no" to disable the options, or define them in the Makefile in 
@@ -66,4 +30,4 @@ RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
 API_SYSEX_ENABLE = no
 
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend

keyboards/tgr/alice/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -43,6 +39,3 @@ RGBLIGHT_CUSTOM_DRIVER = yes
 OPT_DEFS = -DDEBUG_LEVEL=0
 
 SRC += i2c_master.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/tgr/jane/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -44,7 +40,4 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 
 QUANTUM_LIB_SRC = i2c_master.c
 
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
-
 LAYOUTS = tkl_ansi tkl_iso

keyboards/tkc1800/rules.mk

@@ -1,52 +1,15 @@
-
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=8192
-
 
 # Build Options
 #   change yes to no to disable

keyboards/tmo50/keymaps/ottodokto/config.h

@@ -0,0 +1,10 @@
+/*---RGB settings-------------------------------------------- */
+#undef  RGBLIGHT_HUE_STEP
+#undef  RGBLIGHT_SAT_STEP
+#undef  RGBLIGHT_VAL_STEP
+#undef  RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL
+
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17
+#define RGBLIGHT_EFFECT_CHRISTMAS_INTERVAL 200

keyboards/tmo50/keymaps/ottodokto/keymap.c

@@ -0,0 +1,47 @@
+#include QMK_KEYBOARD_H
+
+
+/*---default defines-------------------------------------------- */
+#define LT1_SPC     LT(1, KC_SPC)
+#define LT2_SPC     LT(2, KC_SPC)
+
+
+#define RGB_STA RGB_M_P		// rgb static
+#define RGB_BRE RGB_M_B 	// rgb breathe
+#define RGB_RAI RGB_M_R 	// rgb rainbow
+#define RGB_SWI RGB_M_SW 	// rgb swirl
+#define RGB_SNA RGB_M_SN	// rgb snake9
+#define RGB_KNI RGB_M_K 	// rgb knight
+#define RGB_GRA RGB_M_G 	// rgb gradient
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  // Default layer
+  [0] = LAYOUT_all(
+		KC_VOLU, KC_TAB,  KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I,    KC_O,   KC_P,    KC_LBRC, KC_RBRC, KC_BSPC,
+		KC_VOLD, MT(MOD_LCTL, KC_ESC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K,    KC_L,   KC_SCLN, KC_QUOT, KC_ENT,
+		KC_MUTE, KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_BSLS, KC_RSFT,
+		KC_MPLY, KC_LGUI, KC_LALT, LT2_SPC, LT1_SPC, KC_RALT, MO(3)
+  ),
+  // Numerals layer
+  [1] = LAYOUT_all(
+		KC_BRIU, KC_GESC,  KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8,    KC_9,   KC_0,    KC_MINS, KC_EQL, KC_DEL,
+		KC_BRID, KC_CAPS, _______, _______, _______, _______, _______, _______, KC_4, KC_5,    KC_6,   _______, _______, _______,
+		RGB_MOD, _______, _______, _______, _______, _______, KC_0, KC_1, KC_2, KC_3, _______, _______, _______, _______,
+		RGB_RMOD, _______, _______, _______, _______, _______, _______
+  ),
+  // FN & Navigation layer
+  [2] = LAYOUT_all(
+		KC_PGUP, _______,  KC_END, KC_UP, KC_HOME, _______, _______, _______, KC_F1, KC_F2,    KC_F3,   KC_F4,    _______, _______, _______,
+		KC_PGDN, _______, KC_LEFT, KC_DOWN, KC_RIGHT, _______, _______, _______, KC_F5, KC_F6,    KC_F7,   KC_F8, _______, _______,
+		KC_PSCR, _______, _______, _______, _______, _______, _______, KC_F9, KC_F10, KC_F11, KC_F12, _______, _______, _______,
+		KC_RGUI, _______, _______, _______, _______, _______, _______
+  ),
+  // RGB Control Layer
+  [3] = LAYOUT_all(
+		RGB_SPI, RGB_TOG, RGB_HUD, RGB_VAI, RGB_HUI, _______, _______, _______, _______, _______,    _______,   _______,    _______, _______, RESET,
+		RGB_SPD, _______, RGB_SAD, RGB_VAD, RGB_SAI, _______, _______, _______, _______, _______,    _______,   _______, _______, _______,
+		_______, _______, RGB_STA, RGB_BRE, RGB_RAI, RGB_SWI, RGB_SNA, RGB_KNI, RGB_GRA, VLK_TOG, _______, _______, _______, EEP_RST,
+		_______, _______, _______, _______, _______, _______, _______
+  )
+};

keyboards/tmo50/keymaps/ottodokto/rules.mk

@@ -0,0 +1 @@
+VELOCIKEY_ENABLE = yes 		# Enable velocikey.

keyboards/uk78/rules.mk

@@ -1,45 +1,15 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = atmel-dfu
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-OPT_DEFS += -DBOOTLOADER_SIZE=8192
-
 
 # Build Options
 #   comment out to disable the options.
@@ -53,4 +23,4 @@ SLEEP_LED_ENABLE ?= no  # Breathing sleep LED during USB suspend
 NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
 BACKLIGHT_ENABLE ?= yes  # Enable keyboard backlight functionality
 AUDIO_ENABLE ?= no
-RGBLIGHT_ENABLE ?= yes
+RGBLIGHT_ENABLE ?= yes

keyboards/unikorn/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -43,6 +39,3 @@ RGBLIGHT_CUSTOM_DRIVER = no
 OPT_DEFS = -DDEBUG_LEVEL=0
 
 SRC = i2c_master.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/ut472/rules.mk

@@ -1,53 +1,16 @@
 # MCU name
 MCU = atmega32u2
 
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
 # Bootloader selection
 #   Teensy       halfkay
 #   Pro Micro    caterina
 #   Atmel DFU    atmel-dfu
 #   LUFA DFU     lufa-dfu
 #   QMK DFU      qmk-dfu
-#   atmega32a    bootloadHID
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
-
 # Build Options
 #   change yes to no to disable
 #

keyboards/vision_division/rules.mk

@@ -1,51 +1,15 @@
 # MCU name
 MCU = at90usb1286
 
-# Processor frequency.
+# Bootloader selection
-#     This will define a symbol, F_CPU, in all source code files equal to the
+#   Teensy       halfkay
-#     processor frequency in Hz. You can then use this symbol in your source code to
+#   Pro Micro    caterina
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#   Atmel DFU    atmel-dfu
-#     automatically to create a 32-bit value in your source code.
+#   LUFA DFU     lufa-dfu
-#
+#   QMK DFU      qmk-dfu
-#     This will be an integer division of F_USB below, as it is sourced by
+#   ATmega32A    bootloadHID
-#     F_USB after it has run through any CPU prescalers. Note that this value
+#   ATmega328P   USBasp
-#     does not *change* the processor frequency - it should merely be updated to
+BOOTLOADER = halfkay
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=1024
-
 
 # Build Options
 #   change yes to no to disable

keyboards/winkeyless/bface/rules.mk

@@ -15,14 +15,16 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = bootloadHID
 
 # build options
 BOOTMAGIC_ENABLE = no
@@ -37,11 +39,6 @@ RGBLIGHT_ENABLE = yes
 RGBLIGHT_CUSTOM_DRIVER = yes
 
 OPT_DEFS = -DDEBUG_LEVEL=0
-BOOTLOADER = bootloadHID
 
 # custom matrix setup
 SRC = i2c_master.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
-

keyboards/winkeyless/bmini/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -45,6 +41,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/winkeyless/bminiex/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded 
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -51,6 +47,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c backlight.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/xd004/v1/rules.mk

@@ -1,17 +1,16 @@
 # MCU name
 MCU = atmega16u2
 
-
+# Bootloader selection
-# Boot Section Size in *bytes*
+#   Teensy       halfkay
-#   Teensy halfKay   512
+#   Pro Micro    caterina
-#   Teensy++ halfKay 2048
+#   Atmel DFU    atmel-dfu
-#   Atmel DFU loader 4096
+#   LUFA DFU     lufa-dfu
-#   LUFA bootloader  4096
+#   QMK DFU      qmk-dfu
-#   USBaspLoader     2048
+#   ATmega32A    bootloadHID
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
+#   ATmega328P   USBasp
 BOOTLOADER = atmel-dfu
 
-
 # Build Options
 BOOTMAGIC_ENABLE = lite       # Virtual DIP switch configuration
 MOUSEKEY_ENABLE = no        # Mouse keys(+4700)

keyboards/ymd75/rules.mk

@@ -16,19 +16,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded 
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -56,7 +52,3 @@ SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c backlight.c
-
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/ymd96/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -53,6 +49,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c backlight.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/ymdk/bface/rules.mk

@@ -16,6 +16,16 @@
 # MCU name
 MCU = atmega32a
 
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   ATmega32A    bootloadHID
+#   ATmega328P   USBasp
+BOOTLOADER = bootloadHID
+
 # build options
 BOOTMAGIC_ENABLE = no
 MOUSEKEY_ENABLE = yes
@@ -29,5 +39,3 @@ RGBLIGHT_ENABLE = no
 RGBLIGHT_CUSTOM_DRIVER = no
 
 OPT_DEFS = -DDEBUG_LEVEL=0
-BOOTLOADER = bootloadHID
-

keyboards/ymdk_np21/rules.mk

@@ -15,19 +15,15 @@
 
 # MCU name
 MCU = atmega32a
-PROTOCOL = VUSB
 
-# unsupported features for now
+# Bootloader selection
-NO_UART = yes
+#   Teensy       halfkay
-NO_SUSPEND_POWER_DOWN = yes
+#   Pro Micro    caterina
-
+#   Atmel DFU    atmel-dfu
-# processor frequency
+#   LUFA DFU     lufa-dfu
-F_CPU = 12000000
+#   QMK DFU      qmk-dfu
-
+#   ATmega32A    bootloadHID
-# Bootloader
+#   ATmega328P   USBasp
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = bootloadHID
 
 # build options
@@ -54,6 +50,3 @@ OPT_DEFS = -DDEBUG_LEVEL=0
 # custom matrix setup
 CUSTOM_MATRIX = yes
 SRC = matrix.c i2c.c backlight.c
-
-# programming options
-PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex