[Split] Add config option for DIRECT_PINS_RIGHT (#6479)

Adds support for different direct pin mappings on the halves of a split keyboard.

docs/config_options.md

@@ -248,6 +248,9 @@ There are a few different ways to set handedness for split keyboards (listed in
 * `#define MATRIX_COL_PINS_RIGHT { <col pins> }`
   * If you want to specify a different pinout for the right half than the left half, you can define `MATRIX_ROW_PINS_RIGHT`/`MATRIX_COL_PINS_RIGHT`. Currently, the size of `MATRIX_ROW_PINS` must be the same as `MATRIX_ROW_PINS_RIGHT` and likewise for the definition of columns.
 
+* `#define DIRECT_PINS_RIGHT { { F1, F0, B0, C7 }, { F4, F5, F6, F7 } }`
+  * If you want to specify a different direct pinout for the right half than the left half, you can define `DIRECT_PINS_RIGHT`. Currently, the size of `DIRECT_PINS` must be the same as `DIRECT_PINS_RIGHT`.
+
 * `#define RGBLED_SPLIT { 6, 6 }`
   * See [RGB Light Configuration](#rgb-light-configuration)
 

docs/faq_build.md

@@ -19,7 +19,11 @@ Note that running `make` with `sudo` is generally ***not*** a good idea, and you
 
 ### Linux `udev` Rules
 On Linux, you'll need proper privileges to access the MCU. You can either use
-`sudo` when flashing firmware, or place these files in `/etc/udev/rules.d/`.
+`sudo` when flashing firmware, or place these files in `/etc/udev/rules.d/`. Once added run the following:
+```console
+sudo udevadm control --reload-rules
+sudo udevadm trigger
+```
 
 **/etc/udev/rules.d/50-atmel-dfu.rules:**
 ```
@@ -43,6 +47,28 @@ SUBSYSTEMS=="usb", ATTRS{idVendor}=="feed", MODE:="0666"
 SUBSYSTEMS=="usb", ATTRS{idVendor}=="1c11", MODE:="0666"
 ```
 
+**/etc/udev/rules.d/55-catalina.rules:**
+```
+# ModemManager should ignore the following devices
+ATTRS{idVendor}=="2a03", ENV{ID_MM_DEVICE_IGNORE}="1"
+ATTRS{idVendor}=="2341", ENV{ID_MM_DEVICE_IGNORE}="1"
+```
+
+**Note:** ModemManager filtering only works when not in strict mode, the following commands can update that settings:
+```console
+sudo sed -i 's/--filter-policy=strict/--filter-policy=default/' /lib/systemd/system/ModemManager.service
+sudo systemctl daemon-reload
+sudo systemctl restart ModemManager
+```
+
+**/etc/udev/rules.d/56-dfu-util.rules:**
+```
+# stm32duino
+SUBSYSTEMS=="usb", ATTRS{idVendor}=="1eaf", ATTRS{idProduct}=="0003", MODE:="0666"
+# Generic stm32
+SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="df11", MODE:="0666"
+```
+
 ### Serial device is not detected in bootloader mode on Linux
 Make sure your kernel has appropriate support for your device. If your device uses USB ACM, such as
 Pro Micro (Atmega32u4), make sure to include `CONFIG_USB_ACM=y`. Other devices may require `USB_SERIAL` and any of its sub options.

docs/feature_split_keyboard.md

@@ -160,6 +160,11 @@ There are some settings that you may need to configure, based on how the hardwar
 
 This allows you to specify a different set of pins for the matrix on the right side.  This is useful if you have a board with differently-shaped halves that requires a different configuration (such as Keebio's Quefrency).
 
+```c
+#define DIRECT_PINS_RIGHT { { F1, F0, B0, C7 }, { F4, F5, F6, F7 } }
+```
+
+This allows you to specify a different set of direct pins for the right side.
 
 ```c
 #define RGBLIGHT_SPLIT

keyboards/ai03/lunar/keymaps/muzfuz/keymap.c

@@ -0,0 +1,52 @@
+#include QMK_KEYBOARD_H
+
+// Helpful defines
+#define ESC_CTL     CTL_T(KC_ESCAPE)            // Tap for Esc, hold for Ctrl
+#define FL_KCF LT(1,KC_F)
+#define FL_KCJ LT(1,KC_J)
+#define CMD_ENT LGUI(LSFT(KC_ENT))
+
+enum custom_keycodes {
+  HASHRKT = SAFE_RANGE,
+  CLNEQLS,
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+	[0] = LAYOUT( /* Base */
+		KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSLS, KC_BSLS, LGUI(KC_C),
+		KC_TAB,           KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSPC, LGUI(KC_V),
+		ESC_CTL,          KC_A,    KC_S,    KC_D,    FL_KCF,  KC_G,    KC_H,    FL_KCJ,  KC_K,    KC_L,    KC_SCLN, KC_QUOT,          KC_ENT,  KC_PGUP,
+		KC_LSFT,          KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_LSFT,          KC_UP,   KC_PGDN,
+		CMD_ENT, KC_LALT, KC_LGUI,          KC_SPC,           KC_SPC,           KC_SPC,                    MO(2),   KC_GRV,  KC_LEFT, KC_DOWN, KC_RGHT
+	),
+	[1] = LAYOUT( /* FL */
+		KC_ESC,   KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  KC_DEL,  KC_VOLU,
+		_______,          HASHRKT, _______, KC_LCBR, KC_RCBR, _______, _______, KC_UNDS, KC_PLUS, KC_PIPE,  _______, _______, _______, _______, KC_VOLD,
+		_______,          CLNEQLS, _______, KC_LBRC, KC_RBRC, _______, _______, KC_MINS, KC_EQL,  KC_BSLS,  KC_TILD, KC_GRV,           _______, KC_HOME,
+		_______,          _______, _______, _______, _______, _______, _______, _______,  _______, _______, _______, _______,          _______, KC_END,
+		_______, _______, _______,          _______,          _______,          _______,                    _______, _______, _______, _______, _______
+	),
+	[2] = LAYOUT( /* FN */
+		RESET,   KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  KC_DEL,  _______,
+		KC_CAPS,          _______, KC_UP,   _______, _______, _______, KC_NLCK, KC_P7,   KC_P8,   KC_P9,   KC_MPRV, KC_MPLY, KC_MNXT, _______, _______,
+		_______,          KC_LEFT, KC_DOWN, KC_RGHT, _______, KC_VOLD, KC_VOLU, KC_P4,   KC_P5,   KC_P6,   _______, _______,          _______, _______,
+		_______,          KC_RCTL, KC_RGUI, KC_RALT, _______, _______, KC_P0,   KC_P1,   KC_P2,   KC_P3,   _______, _______,          KC_PGUP, _______,
+		_______, _______, _______,          _______,          _______,          _______,                   _______, _______, KC_HOME, KC_PGDN, KC_END
+	)
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch(keycode) {
+    case HASHRKT:
+      if (record->event.pressed) {
+        SEND_STRING("=>");
+      }
+      break;
+    case CLNEQLS:
+      if (record->event.pressed) {
+        SEND_STRING(":=");
+      }
+      break;
+  }
+  return true;
+}

keyboards/ai03/lunar/keymaps/muzfuz/readme.md

@@ -0,0 +1,5 @@
+# muzfuz's keymap for Lunar
+
+```shell
+make ai03/lunar:muzfuz:dfu
+```

keyboards/akb/raine/config.h

@@ -23,8 +23,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define PRODUCT_ID 0x6060
 #define DEVICE_VER 0x0001
 #define MANUFACTURER AKB
-#define PRODUCT Raine M3
+#define PRODUCT Raine
-#define DESCRIPTION Raine M3
+#define DESCRIPTION Raine
 
 /* key matrix size */
 #define MATRIX_ROWS 5

keyboards/akb/raine/info.json

@@ -68,10 +68,12 @@
                 { "label": "2", "x": 14.25, "y": 3 },
                 { "label": "3", "x": 15.25, "y": 3 },
                 { "label": "Ctrl", "x": 0, "y": 4, "w": 1.25 },
+                { "label": "Win", "x": 1.25, "y": 4},
                 { "label": "Alt", "x": 2.25, "y": 4, "w": 1.25 },
                 { "label": "SPLEFT", "x": 3.5, "y": 4, "w": 2.25 },
                 { "label": "7U", "x": 5.75, "y": 4 },
                 { "label": "SPRIGHT", "x": 6.75, "y": 4, "w": 1.75 },
+                { "label": "alt", "x": 8.5, "y": 4},
                 { "label": "Menu", "x": 9.5, "y": 4, "w": 1.25 },
                 { "x": 11, "y": 4.25 },
                 { "x": 12, "y": 4.25 },

keyboards/akb/raine/keymaps/default/keymap.c

@@ -17,16 +17,16 @@
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   [0] = LAYOUT( /* Base */
-  KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_BSPC, KC_NLCK, KC_SLCK, KC_INS,
+  KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_BSPC, KC_PSLS, KC_PAST, KC_PPLS,
 	KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSLS, KC_P7, KC_P8, KC_P9,
-	MO(1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_HASH, KC_ENT, KC_P4, KC_P5, KC_P6,
+	CTL_T(KC_CAPS), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_NUHS, KC_ENT, KC_P4, KC_P5, KC_P6,
-	KC_LSFT, KC_LALT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_SLSH, KC_LSFT, KC_UP, KC_P1, KC_P2, KC_P3,
+	KC_LSFT, KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_SLSH, KC_RSFT, KC_UP, KC_P1, KC_P2, KC_P3,
-	KC_LCTL, KC_LALT, KC_SPC, KC_SPC, KC_SPC, KC_LGUI, KC_LEFT, KC_DOWN, KC_RGHT, KC_P0, KC_DEL),
+	KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC, KC_BSPC, KC_RALT, MO(1), KC_LEFT, KC_DOWN, KC_RGHT, KC_P0, KC_PDOT),
   [1] = LAYOUT( /* Second */
-  KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, _______, _______, _______,
+  KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_DEL, KC_NLCK, KC_PSCR, KC_INS,
-	_______, _______, _______, _______, _______, _______, _______, _______, _______, KC_LBRC, KC_RBRC, _______, _______, _______, _______,
+	_______, _______, _______, _______, _______, _______, _______, _______, _______, KC_LBRC, KC_RBRC, _______, KC_HOME, KC_UP, KC_PGUP,
-	_______, _______, _______, _______, _______, _______, _______, _______, KC_SCLN, KC_QUOT, _______, _______, _______, _______, _______,
+	_______, _______, _______, _______, _______, _______, _______, _______, KC_SCLN, KC_QUOT, _______, _______, KC_LEFT, KC_SLCK, KC_RGHT,
-	_______, _______, _______, _______, _______, _______, _______, KC_COMM, KC_DOT, _______, _______, _______, _______, _______, _______,
+	_______, _______, _______, _______, _______, _______, _______, KC_COMM, KC_DOT, _______, _______, _______, KC_END, KC_DOWN, KC_PGDN,
-	_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET),
+	_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET),
 };
 

keyboards/akb/raine/raine.h

@@ -23,11 +23,11 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 	K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111,       K113, K114, K115, \
 	K200,       K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, K215, \
 	K300, K301, K302, K303, K304, K305, K306, K307, K308, K309,       K311, K312, K313, K314, K315, \
-	K400,       K402,       K404, K405,       K407,       K409,       K410,       K412, K413, K414, K415  \
+	K400, K401, K402,       K404, K405,       K407, K408, K409,       K410,       K412, K413, K414, K415  \
 ) { \
 	{ K000,  K001,  K002,  K003,  K004,  K005,  K006,  K007,  K008,  K009,  K010,  K011,  K012,  K013,  K014,  K015 }, \
 	{ K100,  K101,  K102,  K103,  K104,  K105,  K106,  K107,  K108,  K109,  K110,  K111,  KC_NO, K113,  K114,  K115 }, \
 	{ K200,  KC_NO, K202,  K203,  K204,  K205,  K206,  K207,  K208,  K209,  K210,  K211,  K212,  K213,  K214,  K215 }, \
 	{ K300,  K301,  K302,  K303,  K304,  K305,  K306,  K307,  K308,  K309,  K311,  KC_NO, K312,  K313,  K314,  K315 }, \
-	{ K400,  KC_NO,  K402,  KC_NO, K404,  K405,  KC_NO, K407,  KC_NO,  K409,  K410,  KC_NO, K412,  K413,  K414,  K415 }  \
+	{ K400,  K401,  K402,  KC_NO, K404,  K405,  KC_NO, K407,  K408,  K409,  K410,  KC_NO, K412,  K413,  K414,  K415 }  \
 }

keyboards/illuminati/is0/config.h

@@ -0,0 +1,251 @@
+/*
+Copyright 2019 Ryota Goto
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xA103
+#define PRODUCT_ID      0x0012
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Illuminati Works
+#define PRODUCT         iS0
+#define DESCRIPTION     no
+
+/* key matrix size */
+#define MATRIX_ROWS 1
+#define MATRIX_COLS 1
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D2 }
+#define MATRIX_COL_PINS { D0 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+/*
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
+
+#define BACKLIGHT_PIN B7
+#define BACKLIGHT_BREATHING
+#define BACKLIGHT_LEVELS 5
+
+// #define RGB_DI_PIN E2
+// #ifdef RGB_DI_PIN
+//   #define RGBLED_NUM 16
+//   #define RGBLIGHT_HUE_STEP 8
+//   #define RGBLIGHT_SAT_STEP 8
+//   #define RGBLIGHT_VAL_STEP 8
+//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+// /*== all animations enable ==*/
+//   #define RGBLIGHT_ANIMATIONS
+// /*== or choose animations ==*/
+//   #define RGBLIGHT_EFFECT_BREATHING
+//   #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+//   #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+//   #define RGBLIGHT_EFFECT_SNAKE
+//   #define RGBLIGHT_EFFECT_KNIGHT
+//   #define RGBLIGHT_EFFECT_CHRISTMAS
+//   #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+//   #define RGBLIGHT_EFFECT_RGB_TEST
+//   #define RGBLIGHT_EFFECT_ALTERNATING
+// /*== customize breathing effect ==*/
+//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+//   /*==== use exp() and sin() ====*/
+//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+// #endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCE 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
+#endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/illuminati/is0/info.json

@@ -0,0 +1,12 @@
+{
+    "keyboard_name": "iS0", 
+    "url": "", 
+    "maintainer": "ai03", 
+    "width": 1.5, 
+    "height": 2, 
+    "layouts": {
+        "LAYOUT": {
+            "layout": [{"x":0.25, "y":0, "w":1.25, "h":2}]
+        }
+    }
+}

keyboards/illuminati/is0/is0.c

@@ -0,0 +1,51 @@
+/* Copyright 2019 Ryota Goto
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "is0.h"
+
+// Optional override functions below.
+// You can leave any or all of these undefined.
+// These are only required if you want to perform custom actions.
+
+/*
+
+void matrix_init_kb(void) {
+  // put your keyboard start-up code here
+  // runs once when the firmware starts up
+
+  matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+  // put your looping keyboard code here
+  // runs every cycle (a lot)
+
+  matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  // put your per-action keyboard code here
+  // runs for every action, just before processing by the firmware
+
+  return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+  // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+  led_set_user(usb_led);
+}
+
+*/

keyboards/illuminati/is0/is0.h

@@ -0,0 +1,33 @@
+/* Copyright 2019 Ryota Goto
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ */
+#define LAYOUT( \
+    K0 \
+) \
+{ \
+    { K0 } \
+}

keyboards/illuminati/is0/keymaps/ctrlaltdel/keymap.c

@@ -0,0 +1,38 @@
+/* Copyright 2019 Ryota Goto
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [0] = LAYOUT( /* Base */
+    LCTL(LALT(KC_DEL))
+  ),
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/illuminati/is0/keymaps/ctrlaltdel/readme.md

@@ -0,0 +1,3 @@
+# The ctrlaltdel keymap for is0
+
+A simple keymap to send Ctrl + Alt + Del on keypress.

keyboards/illuminati/is0/keymaps/default/keymap.c

@@ -0,0 +1,52 @@
+/* Copyright 2019 Ryota Goto
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+// Defines the keycodes used by our macros in process_record_user
+enum custom_keycodes {
+  KBINFO = SAFE_RANGE
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [0] = LAYOUT( /* Base */
+    KBINFO
+  ),
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+    case KBINFO:
+      if (record->event.pressed) {
+        SEND_STRING("Hello from Illuminati Works");
+      } else {
+		SEND_STRING("iS0 working properly");
+      }
+      break;
+  }
+  return true;
+}
+
+void matrix_init_user(void) {
+
+}
+
+void matrix_scan_user(void) {
+
+}
+
+void led_set_user(uint8_t usb_led) {
+
+}

keyboards/illuminati/is0/keymaps/default/readme.md

@@ -0,0 +1,3 @@
+# The default keymap for is0
+
+Simply to verify that it works.

keyboards/illuminati/is0/readme.md

@@ -0,0 +1,15 @@
+# iS0
+
+![is0](https://i.imgur.com/ObiNJ2O.jpg)
+
+Single-key macropad  
+
+Keyboard Maintainer: [ai03](https://github.com/ai03-2725)  
+Hardware Supported: iS0 by Illuminati Works  
+Hardware Availability: [Illuminati Works website](https://illuminati.works/is0/)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make illuminati/is0:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/illuminati/is0/rules.mk

@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u2
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes           # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)

keyboards/kbdfans/kbdpad/mk1/config.h

@@ -0,0 +1,38 @@
+/*
+Copyright 2017 Luiz Ribeiro <[email protected]>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+#define VENDOR_ID       0x20A0
+#define PRODUCT_ID      0x422D
+#define MANUFACTURER    KBDfans
+#define PRODUCT         KBDPAD-MKI
+
+#define MATRIX_ROWS 6
+#define MATRIX_COLS 4
+
+//                        0   1   2   3   4   5   
+#define MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5 }
+#define MATRIX_COL_PINS { A0, A1, A2, A3 }
+#define UNUSED_PINS
+
+#define DIODE_DIRECTION COL2ROW
+#define DEBOUNCE 5
+
+#define BACKLIGHT_LEVELS 1

keyboards/kbdfans/kbdpad/mk1/info.json

@@ -0,0 +1,12 @@
+{
+  "keyboard_name": "KBDFans KBDPad MKI", 
+  "url": "", 
+  "maintainer": "qmk", 
+  "width": 4, 
+  "height": 6.25, 
+  "layouts": {
+      "LAYOUT": {
+          "layout": [{"x":2, "y":0}, {"x":3, "y":0}, {"x":0, "y":1.25}, {"x":1, "y":1.25}, {"x":2, "y":1.25}, {"x":3, "y":1.25}, {"x":0, "y":2.25}, {"x":1, "y":2.25}, {"x":2, "y":2.25}, {"x":0, "y":3.25}, {"x":1, "y":3.25}, {"x":2, "y":3.25}, {"x":3, "y":2.25, "h":2}, {"x":0, "y":4.25}, {"x":1, "y":4.25}, {"x":2, "y":4.25}, {"x":0, "y":5.25, "w":2}, {"x":2, "y":5.25}, {"x":3, "y":4.25, "h":2}]
+      }
+  }
+}

keyboards/kbdfans/kbdpad/mk1/keymaps/default/keymap.c

@@ -0,0 +1,27 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[0] = LAYOUT(\
+  KC_DEL,  KC_BSPC,                    \
+  KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS,  \
+  KC_P7,   KC_P8,   KC_P9,             \
+  KC_P4,   KC_P5,   KC_P6,   KC_PPLS,  \
+  KC_P1,   KC_P2,   KC_P3,             \
+  KC_P0,   KC_PDOT, KC_PENT)           \
+};

keyboards/kbdfans/kbdpad/mk1/mk1.c

@@ -0,0 +1,88 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include "i2c_master.h"
+#include "quantum.h"
+
+#ifdef RGBLIGHT_ENABLE
+#include "rgblight.h"
+extern rgblight_config_t rgblight_config;
+
+void rgblight_set(void) {
+    if (!rgblight_config.enable) {
+        for (uint8_t i = 0; i < RGBLED_NUM; i++) {
+            led[i].r = 0;
+            led[i].g = 0;
+            led[i].b = 0;
+        }
+    }
+
+    i2c_init();
+    i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+}
+#endif
+
+void matrix_init_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+    if (rgblight_config.enable) {
+        i2c_init();
+        i2c_transmit(0xb0, (uint8_t*)led, 3 * RGBLED_NUM, 100);
+    }
+#endif
+    // call user level keymaps, if any
+    matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+#ifdef RGBLIGHT_ENABLE
+    rgblight_task();
+#endif
+    matrix_scan_user();
+    /* Nothing else for now. */
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+void backlight_init_ports(void) {
+    // initialize pins D0, D1, D4 and D6 as output
+    setPinOutput(D0);
+    setPinOutput(D1);
+    setPinOutput(D4);
+    setPinOutput(D6);
+
+    // turn backlight LEDs on
+    writePinHigh(D0);
+    writePinHigh(D1);
+    writePinHigh(D4);
+    writePinHigh(D6);
+}
+
+void backlight_set(uint8_t level) {
+	if (level == 0) {
+        // turn backlight LEDs off
+        writePinLow(D0);
+        writePinLow(D1);
+        writePinLow(D4);
+        writePinLow(D6);
+	} else {
+        // turn backlight LEDs on
+        writePinHigh(D0);
+        writePinHigh(D1);
+        writePinHigh(D4);
+        writePinHigh(D6);
+	}
+}

keyboards/kbdfans/kbdpad/mk1/mk1.h

@@ -0,0 +1,38 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+// This a shortcut to help you visually see your layout.
+// The first section contains all of the arguments
+// The second converts the arguments into a two-dimensional array
+
+#define LAYOUT(   \
+  k52,  k53,           \
+  k40, k41, k42, k43,  \
+  k30, k31, k32,       \
+  k20, k21, k22, k23,  \
+  k10, k11, k12,       \
+  k00, k02, k03        \
+){ \
+  { k00,   KC_NO, k02, k03   }, \
+  { k10,   k11,   k12, KC_NO }, \
+  { k20,   k21,   k22, k23   }, \
+  { k30,   k31,   k32, KC_NO }, \
+  { k40,   k41,   k42, k43   }, \
+  { KC_NO, KC_NO, k52, k53   }, \
+}

keyboards/kbdfans/kbdpad/mk1/readme.md

@@ -0,0 +1,47 @@
+# KBDPad MKI
+
+Custom numpad. 
+
+Keyboard Maintainer: [MechMerlin](https://github.com/mechmerlin)  
+Hardware Supported: KBDPad MKI  
+Hardware Availability: No longer available. 
+
+
+Make example for this keyboard (after setting up your build environment):
+
+    make kbdfans/kbdpad/mk1:default
+
+Flashing
+
+ps2avr(GB) boards use an atmega32a microcontroller and a different bootloader. It is not flashable using the regular QMK methods. 
+
+**Reset Key:** Hold down the key located at `K00`, commonly programmed as `0` while plugging in the keyboard.
+
+Windows: 
+1. Download [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
+2. Place your keyboard into reset. 
+3. Press the `Find Device` button and ensure that your keyboard is found.
+4. Press the `Open .hex File` button and locate the `.hex` file you created.
+5. Press the `Flash Device` button and wait for the process to complete. 
+
+macOS:
+1. Install homebrew by typing the following:   
+    ```
+    /usr/bin/ruby -e "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/master/install)"
+    ```
+2. Install `crosspack-avr`.  
+    ```
+    brew cask install crosspack-avr
+    ```
+3. Install the following packages:
+    ```
+    brew install python3
+    pip3 install pyusb
+    brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+    ```
+
+4. Place your keyboard into reset. 
+5. Flash the board by typing `bootloadHID -r` followed by the path to your `.hex` file. 
+
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/kbdfans/kbdpad/mk1/rules.mk

@@ -0,0 +1,48 @@
+# Copyright 2017 Luiz Ribeiro <[email protected]>
+#
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+# MCU name
+MCU = atmega32a
+PROTOCOL = VUSB
+
+# unsupported features for now
+NO_UART = yes
+NO_SUSPEND_POWER_DOWN = yes
+
+# processor frequency
+F_CPU = 12000000
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = bootloadHID
+
+# build options
+BOOTMAGIC_ENABLE = no
+MOUSEKEY_ENABLE = yes
+EXTRAKEY_ENABLE = yes
+CONSOLE_ENABLE = yes
+COMMAND_ENABLE = yes
+BACKLIGHT_ENABLE = yes
+RGBLIGHT_ENABLE = no
+RGBLIGHT_CUSTOM_DRIVER = no
+
+OPT_DEFS = -DDEBUG_LEVEL=0
+
+QUANTUM_LIB_SRC = i2c_master.c
+
+# programming options
+PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex

keyboards/kbdfans/kbdpad/mk1/usbconfig.h

@@ -0,0 +1,393 @@
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
+ */
+
+#pragma once
+
+#include "config.h"
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME      D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT      3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT       2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC       0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME   D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT          4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT    1
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3   1
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER              3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN           USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT          0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE      0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL      1
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED         0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+#define USB_CFG_MAX_BUS_POWER           500
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE      1
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ       0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL        0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS          0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK()              hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF                   1
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ *     in      YL, TCNT0
+ *     sts     timer0Snapshot, YL
+ *     endm
+ * #endif
+ * #define USB_SOF_HOOK                    myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING     0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define USB_CFG_VENDOR_ID       (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_ID       (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME     'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'
+#define USB_CFG_VENDOR_NAME_LEN 13
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME     'p', 's', '2', 'a', 'v', 'r', 'G', 'B'
+#define USB_CFG_DEVICE_NAME_LEN 8
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+/*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS        0
+#define USB_CFG_DEVICE_SUBCLASS     0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS     3   /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS  1   /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL  1   /* Keyboard */
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ *     you want RAM pointers.
+ *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ *     in static memory is in RAM, not in flash memory.
+ *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ *     the driver must know the descriptor's length. The descriptor itself is
+ *     found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ *   char usbDescriptorDevice[];
+ *   char usbDescriptorConfiguration[];
+ *   char usbDescriptorHidReport[];
+ *   char usbDescriptorString0[];
+ *   int usbDescriptorStringVendor[];
+ *   int usbDescriptorStringDevice[];
+ *   int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ *   USB_CFG_DESCR_PROPS_DEVICE
+ *   USB_CFG_DESCR_PROPS_CONFIGURATION
+ *   USB_CFG_DESCR_PROPS_STRINGS
+ *   USB_CFG_DESCR_PROPS_STRING_0
+ *   USB_CFG_DESCR_PROPS_STRING_VENDOR
+ *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ *   USB_CFG_DESCR_PROPS_HID
+ *   USB_CFG_DESCR_PROPS_HID_REPORT
+ *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int  serialNumberDescriptor[] = {
+ *     USB_STRING_DESCRIPTOR_HEADER(6),
+ *     'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE                  0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION           USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
+#define USB_CFG_DESCR_PROPS_STRINGS                 0
+#define USB_CFG_DESCR_PROPS_STRING_0                0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
+#define USB_CFG_DESCR_PROPS_HID                     USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID                     0
+#define USB_CFG_DESCR_PROPS_HID_REPORT              USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID_REPORT              0
+#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG            MCUCR */
+/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         GIMSK */
+/* #define USB_INTR_ENABLE_BIT     INT0 */
+/* #define USB_INTR_PENDING        GIFR */
+/* #define USB_INTR_PENDING_BIT    INTF0 */
+/* #define USB_INTR_VECTOR         INT0_vect */
+
+/* Set INT1 for D- falling edge to count SOF */
+/* #define USB_INTR_CFG            EICRA */
+#define USB_INTR_CFG_SET        ((1 << ISC11) | (0 << ISC10))
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         EIMSK */
+#define USB_INTR_ENABLE_BIT     INT1
+/* #define USB_INTR_PENDING        EIFR */
+#define USB_INTR_PENDING_BIT    INTF1
+#define USB_INTR_VECTOR         INT1_vect

keyboards/keebio/iris/keymaps/blucky/config.h

@@ -0,0 +1,34 @@
+/*
+Copyright 2019 Brian Luckenbill 
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#define C6_AUDIO
+
+#undef  RGBLED_NUM
+#define RGBLED_NUM                  12
+#define RGBLIGHT_HUE_STEP           8
+#define RGBLIGHT_SAT_STEP           8
+#define RGBLIGHT_VAL_STEP           8
+#define RGBLIGHT_ANIMATIONS
+
+#define MOUSEKEY_DELAY              300
+#define MOUSEKEY_INTERVAL           50
+#define MOUSEKEY_MAX_SPEED          10
+#define MOUSEKEY_TIME_TO_MAX        20
+#define MOUSEKEY_WHEEL_MAX_SPEED    8
+#define MOUSEKEY_WHEEL_TIME_TO_MAX  40

keyboards/keebio/iris/keymaps/blucky/keymap.c

@@ -0,0 +1,86 @@
+#include QMK_KEYBOARD_H
+
+enum layer_names {
+    _QWERTY,
+    _LAYER1,
+    _LAYER2,
+    _LAYER3
+};
+
+#define WM_0     LGUI(KC_ENT)
+#define WM_1     LGUI(KC_BSPC)
+#define WM_2     LGUI(KC_DEL)
+#define WM_3     SGUI(KC_ENT)
+#define WM_4     SGUI(KC_BSPC)
+#define WM_5     SGUI(KC_DEL)
+#define WM_6     SGUI(KC_TAB)
+
+#define LAYER1   TT(_LAYER1)
+#define LAYER2   TT(_LAYER2)
+
+#define CS_U     C(S(KC_UP))
+#define CS_D     C(S(KC_DOWN))
+#define CS_SPC   C(S(KC_SPC))
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+  [_QWERTY] = LAYOUT(
+  //┌────────┬────────┬────────┬────────┬────────┬────────┐                          ┌────────┬────────┬────────┬────────┬────────┬────────┐
+      KC_GESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,                               KC_6,    KC_7,    KC_8,    KC_9,    KC_0,   KC_EQL,
+  //├────────┼────────┼────────┼────────┼────────┼────────┤                          ├────────┼────────┼────────┼────────┼────────┼────────┤
+      KC_TAB,   KC_Q,     KC_W,   KC_E,    KC_R,    KC_T,                               KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,   KC_BSPC,
+  //├────────┼────────┼────────┼────────┼────────┼────────┤                          ├────────┼────────┼────────┼────────┼────────┼────────┤
+      LAYER1,   KC_A,    KC_S,    KC_D,    KC_F,    KC_G,                               KC_H,    KC_J,    KC_K,    KC_L,  KC_SCLN,  KC_QUOT,
+  //├────────┼────────┼────────┼────────┼────────┼────────┼────────┐        ┌────────┼────────┼────────┼────────┼────────┼────────┼────────┤
+      KC_LSFT,  KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,   KC_LGUI,         KC_RGUI,   KC_N,    KC_M,  KC_COMM,  KC_DOT, KC_SLSH,  LAYER2,
+  //└────────┴────────┴────────┴───┬────┴───┬────┴───┬────┴───┬────┘        └───┬────┴───┬────┴───┬────┴───┬────┴────────┴────────┴────────┘
+                                     KC_LCTL, KC_LALT, KC_SPC,                    KC_ENT, KC_RGUI,  WM_0
+  //                               └────────┴────────┴────────┘                 └────────┴────────┴────────┘
+  ),
+
+
+  [_LAYER1] = LAYOUT(
+  //┌────────┬────────┬────────┬────────┬────────┬────────┐                          ┌────────┬────────┬────────┬────────┬────────┬────────┐
+     KC_CAPS,  KC_F1,    KC_F2,  KC_F3,   KC_F4,   KC_F5,                              KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_MINS,
+  //├────────┼────────┼────────┼────────┼────────┼────────┤                          ├────────┼────────┼────────┼────────┼────────┼────────┤
+     KC_SLCK,  KC_PSCR, KC_NO,   KC_NO,   KC_NO,    KC_NO,                             KC_PGUP, KC_PGDN, KC_HOME, KC_END,  KC_NO,   KC_DEL,
+  //├────────┼────────┼────────┼────────┼────────┼────────┤                          ├────────┼────────┼────────┼────────┼────────┼────────┤
+     KC_NO,    KC_NO, C(KC_LEFT), KC_NO, C(KC_RGHT), KC_NO,                            KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT, KC_NO,   KC_INS,
+  //├────────┼────────┼────────┼────────┼────────┼────────┼────────┐        ┌────────┼────────┼────────┼────────┼────────┼────────┼────────┤
+     KC_RSFT,  KC_NO,    WM_5,    WM_4,    WM_3,    WM_2,   MU_TOG,            AU_TOG,  KC_NO,  KC_NO,   KC_LBRC, KC_RBRC, KC_BSLS, KC_NO,
+  //└────────┴────────┴────────┴───┬────┴───┬────┴───┬────┴───┬────┘        └───┬────┴───┬────┴───┬────┴───┬────┴────────┴────────┴────────┘
+                                      WM_1,  KC_LGUI,  KC_PIPE,                   KC_UNDS, KC_RCTL, KC_RALT
+  //                               └────────┴────────┴────────┘                 └────────┴────────┴────────┘
+  ),
+
+
+  [_LAYER2] = LAYOUT(
+  //┌────────┬────────┬────────┬────────┬────────┬────────┐                          ┌────────┬────────┬────────┬────────┬────────┬────────┐
+      KC_ESC,  KC_F11,  KC_F12,  KC_F13,  KC_F14,  KC_F15,                             KC_F16,  KC_F17,  KC_F18,  KC_F19,  KC_F20,  KC_NO,
+  //├────────┼────────┼────────┼────────┼────────┼────────┤                          ├────────┼────────┼────────┼────────┼────────┼────────┤
+      KC_NO,   KC_NO,   KC_NO,   CS_SPC,   CS_U,  S(KC_PGUP),                         RGB_VAI, RGB_HUI, RGB_SAI, RGB_M_SW,RGB_M_R,  KC_NO,
+  //├────────┼────────┼────────┼────────┼────────┼────────┤                          ├────────┼────────┼────────┼────────┼────────┼────────┤
+      KC_NO,   KC_NO,   KC_NO,   KC_NO,    CS_D,  S(KC_PGDN),                         RGB_VAD, RGB_HUD, RGB_SAD,  KC_NO,   KC_NO,   KC_NO,
+  //├────────┼────────┼────────┼────────┼────────┼────────┼────────┐        ┌────────┼────────┼────────┼────────┼────────┼────────┼────────┤
+     KC_LSFT, KC_VOLD, KC_VOLU, KC_MUTE, KC_BRID, KC_BRIU,  MU_MOD,           AU_OFF,  KC_RCTL, KC_LCTL, KC_RALT, KC_LALT, KC_DEL,  KC_NO,
+  //└────────┴────────┴────────┴───┬────┴───┬────┴───┬────┴───┬────┘        └───┬────┴───┬────┴───┬────┴───┬────┴────────┴────────┴────────┘
+                                      WM_6,  VLK_TOG, RGB_MOD,                   RGB_TOG, BL_TOGG,  BL_STEP
+  //                               └────────┴────────┴────────┘                 └────────┴────────┴────────┘
+  ),
+
+
+  [_LAYER3] = LAYOUT(
+  //┌────────┬────────┬────────┬────────┬────────┬────────┐                          ┌────────┬────────┬────────┬────────┬────────┬────────┐
+      KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,                              KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,
+  //├────────┼────────┼────────┼────────┼────────┼────────┤                          ├────────┼────────┼────────┼────────┼────────┼────────┤
+      KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,                              KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,
+  //├────────┼────────┼────────┼────────┼────────┼────────┤                          ├────────┼────────┼────────┼────────┼────────┼────────┤
+      KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,                              KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,
+  //├────────┼────────┼────────┼────────┼────────┼────────┼────────┐        ┌────────┼────────┼────────┼────────┼────────┼────────┼────────┤
+      KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,            KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,
+  //└────────┴────────┴────────┴───┬────┴───┬────┴───┬────┴───┬────┘        └───┬────┴───┬────┴───┬────┴───┬────┴────────┴────────┴────────┘
+                                     KC_NO,   KC_NO,   KC_NO,                     KC_NO,   KC_NO,   KC_NO
+  //                               └────────┴────────┴────────┘                 └────────┴────────┴────────┘
+  )
+
+};

keyboards/keebio/iris/keymaps/blucky/rules.md

@@ -0,0 +1,7 @@
+# blucky's keymap for iris rev 2 w/ speaker, backlight and RGB and rev 3
+
+```shell
+make keebio/iris/rev2:blucky
+
+make keebio/iris/rev3:blucky
+```

keyboards/keebio/iris/keymaps/blucky/rules.mk

@@ -0,0 +1,5 @@
+RGBLIGHT_ENABLE   = yes
+BACKLIGHT_ENABLE  = yes
+VELOCIKEY_ENABLE  = yes
+MOUSEKEY_ENABLE   = yes
+AUDIO_ENABLE      = no

keyboards/melody96/keymaps/zunger/keymap.c

@@ -54,7 +54,6 @@ enum layers_keymap {
 // autogenerate the keymaps for the other layers.
 // TODO: It would also be nice to be able to put the actual code points in here, rather than
 // numbers.
-// TODO: Also add checkmark and dengir.
 
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
@@ -70,9 +69,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * | ∅ |   |   |   |   |   |   |   |   |   |   |   |   |   |   |   |   |   |   |  SHIFTCADET
    * |---------------------------------------------------------------------------|
    * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | + | BKSPC |LCK| / | * | - |
-   * | ` |   |   |   |   |   |   |   |   |   |   | ∝ | ∼ | BKSPC |LCK| ⊘ | ⊙ | ⊖ |
+   * | ` | ¡ |   | £ |   |   |   |   | ° |   |   | ∝ | ∼ | BKSPC |LCK| ⊘ | ⊙ | ⊖ |
-   * | ` |   |   |   |   |   |   |   |   |   |   |   | ≁ | BKSPC |LCK|   | ⊗ |   |
+   * | ` | ¿ |   | € |   |   |   |   |   |   |   |   | ≁ | BKSPC |LCK|   | ⊗ |   |
-   * |   |   |   |   |   |   |   |   |   |   |   |   | ± | BKSPC |LCK|   |   |   |
+   * |   |  ̀ |  ́ |  ̂ |  ̃ |  ̈ |  ̄ |   |   |   |   |   | ± | BKSPC |LCK|   | × |   | [3]
    * |   |   |   |   |   |   |   |   |   |   |   |   | ∓ | BKSPC |LCK|   |   |   |
    * |---------------------------------------------------------------------------|
    * | TAB  | Q | W | E | R | T | Y | U | I | O | P | [ | ] |  \ | 7 | 8 | 9 |   |
@@ -104,6 +103,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    * clicks the mouse, and SHIFT+CADET+FIVE right-clicks.
    * [2] The Greek letters in this row are the three modifier keys (GREEK, CADET, FN),
    * not the Unicode Greek letters.
+   * [3] The accent marks in this row are combining accent marks, which may be put after
+   * a character to combine it. In order, they are grave, acute, circumflex, tilde,
+   * diaresis (umlaut), and macron.
   */
   // NB: Using GESC for escape in the QWERTY layer as a temporary hack because I messed up the
   // switch on the KC_GRV key; change back to KC_ESC once this is fixed.
@@ -116,14 +118,14 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     KC_LCTL, KC_LALT, KC_LGUI,                            KC_SPC,                             KC_GREEK,KC_CADET,MO_FN,   KC_LEFT, KC_DOWN, KC_RGHT, KC_P0,   KC_PDOT, KC_PENT),
 	[_GREEK] = LAYOUT_hotswap(
     KC_GRV,  H(00b9), H(00b2), H(00b3), H(2074), H(2075), H(2076), H(2077), H(2078), H(2079), H(2070), H(207b), H(207a), H(207d), H(207e), XXXXXXX, XXXXXXX, XXXXXXX, _______,
-    KC_GRV,  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, H(221d), H(223c),          _______, _______, H(2298), H(2299), H(2296),
+    KC_GRV,  H(00a1), _______, H(00a3), _______, _______, _______, _______, H(00b0), _______, _______, H(221d), H(223c),          _______, _______, H(2298), H(2299), H(2296),
     _______, H(03b8), H(03c9), H(03b5), H(03c1), H(03c4), H(03c8), H(03c5), H(03b9), H(03bf), H(03c0), KC_LBRC, KC_RBRC,          KC_BSLS, KC_P7,   KC_P8,   KC_P9,
     _______, H(03b1), H(03c3), H(03b4), H(03c6), H(03b3), H(03b7), H(03d1), H(03ba), H(03bb), H(22ef), H(22c5),                   _______, KC_P4,   KC_P5,   KC_P6,   H(2295),
     _______,          H(03b6), H(03be), H(03c7), H(03c2), H(03b2), H(03bd), H(03bc), H(226a), H(226b), H(222b), _______,          _______, KC_P1,   KC_P2,   KC_P3,
     _______, _______, _______,                            _______,                            _______, _______, _______, _______, _______, _______, KC_P0,   KC_PDOT, KC_PENT),
 	[_SHIFTGREEK] = LAYOUT_hotswap(
     KC_GRV,  H(2081), H(2082), H(2083), H(2084), H(2085), H(2086), H(2087), H(2088), H(2089), H(2080), H(208b), H(208a), H(208d), H(208e), XXXXXXX, XXXXXXX, XXXXXXX, _______,
-    KC_GRV,  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, XXXXXXX, H(2241),          _______, _______, XXXXXXX, H(2297), XXXXXXX,
+    KC_GRV,  H(00bf), _______, H(20ac), _______, _______, _______, _______, _______, _______, _______, XXXXXXX, H(2241),          _______, _______, XXXXXXX, H(2297), XXXXXXX,
     _______, H(0398), H(03a9), H(0395), H(03a1), H(03a4), H(03a8), H(03a5), H(0399), H(039f), H(03a0), KC_LBRC, KC_RBRC,          KC_BSLS, KC_P7,   KC_P8,   KC_P9,
     _______, H(0391), H(03a3), H(0394), H(03a6), H(0393), H(0397), XXXXXXX, H(039a), H(039b), H(2026), H(2234),                   _______, KC_P4,   KC_P5,   KC_P6,   H(2295),
     _______,          H(0396), H(039e), H(03a7), H(2714), H(0392), H(039d), H(039c), H(2272), H(2273), XXXXXXX, _______,          _______, KC_P1,   KC_P2,   KC_P3,
@@ -131,7 +133,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   // TODO: Add mouse keys to keypad.
 	[_CADET] = LAYOUT_hotswap(
     H(00AC), KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______,
-    KC_GRV,  XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, H(00b1),          _______, _______, XXXXXXX, XXXXXXX, XXXXXXX,
+    KC_GRV,  H(0300), H(0301), H(0302), H(0303), H(0308), H(0304), XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, H(00b1),          _______, _______, XXXXXXX, H(00d7), XXXXXXX,
     _______, H(2227), H(2228), H(2229), H(222a), H(2282), H(2283), H(2200), H(221e), H(2203), H(2202), H(2208), XXXXXXX,          XXXXXXX, KC_P7,   KC_P8,   KC_P9,
     _______, H(22a5), H(22a4), H(22a2), H(22a3), H(2191), H(2193), H(2190), H(2192), H(2194), XXXXXXX, XXXXXXX,                   _______, KC_P4,   KC_P5,   KC_P6,   XXXXXXX,
     _______,          XXXXXXX, XXXXXXX, H(2260), H(2248), H(2261), H(2264), H(2265), XXXXXXX, XXXXXXX, H(00f7), _______,          _______, KC_P1,   KC_P2,   KC_P3,
@@ -145,7 +147,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
     _______, _______, _______,                            _______,                            _______, _______, _______, _______, _______, _______, KC_P0,   KC_PDOT, KC_PENT),
 
   // Function layer is mostly for keyboard meta-control operations. Lots of this is just from the
-  // default layout; TODO make it nicer, add Unicode mode switchers.
+  // default layout; TODO make it nicer.
 	[_FUNCTION] = LAYOUT_hotswap(
     RESET,   _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MUTE, KC_VOLD, KC_VOLU, _______, _______, _______,
     _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______, _______, _______, _______,

keyboards/planck/keymaps/dsanchezseco/keymap.c

@@ -11,7 +11,7 @@ enum planck_layers {
 };
 
 enum planck_keycodes {
-  DVORAK,
+  DVORAK = SAFE_RANGE,
 };
 
 #define LOWER MO(_LOWER)
@@ -77,17 +77,17 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  * ,-----------------------------------------------------------------------------------
  * |      | Reset|      |      |      |      |      |      |      |      |      |  Del |
  * |------+------+------+------+------+-------------+------+------+------+------+------|
- * |      |      |      |Aud on|Audoff|AGnorm|AGswap|      |      |      |      |      |
+ * |      |      |      |      |      |      |      |      |      |      |      |      |
  * |------+------+------+------+------+------|------+------+------+------+------+------|
- * |      |Voice-|Voice+|Mus on|Musoff|MIDIon|MIDIof|      |      |      |      |      |
+ * |      |PtrScr|      |Mus on|Musoff|      |      |      |      |      |      |      |
  * |------+------+------+------+------+------+------+------+------+------+------+------|
  * |      |      |      |      |      |      |      |      |      |      |      |      |
  * `-----------------------------------------------------------------------------------'
  */
 [_ADJUST] = LAYOUT_planck_grid(
-    _______, RESET,   DEBUG,   RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUD, RGB_SAI, RGB_SAD,  RGB_VAI, RGB_VAD, KC_DEL,
+    _______, RESET,   _______, RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUD, RGB_SAI, RGB_SAD,  RGB_VAI, RGB_VAD, KC_DEL,
-    _______, _______, MU_MOD,  AU_ON,   AU_OFF,  AG_NORM, AG_SWAP, _______, _______,  _______, _______, _______,
+    _______, _______, _______, _______, _______, _______, _______, _______, _______,  _______, _______, _______,
-    _______, MUV_DE,  MUV_IN,  MU_ON,   MU_OFF,  MI_ON,   MI_OFF,  TERM_ON, TERM_OFF, _______, _______, _______,
+    _______, KC_PSCR, _______, MU_ON,   MU_OFF,  _______, _______, _______, _______,  _______, _______, _______,
     _______, _______, _______, _______, _______, _______, _______, _______, _______,  _______, _______, _______
 )
 

keyboards/qwertyydox/config.h

@@ -15,8 +15,7 @@ You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
-#ifndef REV1_CONFIG_H
+#pragma once
-#define REV1_CONFIG_H
 
 #include "config_common.h"
 
@@ -33,6 +32,16 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define MATRIX_ROWS 8
 #define MATRIX_COLS 7
 
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
 // wiring of each half
 #define MATRIX_ROW_PINS { B6, B2, B3, B1 }
 #define MATRIX_COL_PINS { F7, F6, F5, C6, D7, D4, D1 }
@@ -40,30 +49,139 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* COL2ROW or ROW2COL */
 #define DIODE_DIRECTION COL2ROW
 
-/* define if matrix has ghost */
+/*
-//#define MATRIX_HAS_GHOST
+ * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
+ */
+#define SOFT_SERIAL_PIN D0
 
-/* number of backlight levels */
+// #define BACKLIGHT_PIN E6
-// #define BACKLIGHT_LEVELS 3
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 5
 
-/* Set 0 if debouncing isn't needed */
+#define RGB_DI_PIN D6
+#ifdef RGB_DI_PIN
+    #define RGBLED_NUM 12
+    #define RGBLIGHT_HUE_STEP 8
+    #define RGBLIGHT_SAT_STEP 8
+    #define RGBLIGHT_VAL_STEP 8
+    #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
+    #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
+    /*== all animations enable ==*/
+    #define RGBLIGHT_ANIMATIONS
+    // /*== or choose animations ==*/
+    //     #define RGBLIGHT_EFFECT_BREATHING
+    //     #define RGBLIGHT_EFFECT_RAINBOW_MOOD
+    //     #define RGBLIGHT_EFFECT_RAINBOW_SWIRL
+    //     #define RGBLIGHT_EFFECT_SNAKE
+    //     #define RGBLIGHT_EFFECT_KNIGHT
+    //     #define RGBLIGHT_EFFECT_CHRISTMAS
+    //     #define RGBLIGHT_EFFECT_STATIC_GRADIENT
+    //     #define RGBLIGHT_EFFECT_RGB_TEST
+    //     #define RGBLIGHT_EFFECT_ALTERNATING
+    // /*== customize breathing effect ==*/
+    //     /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
+    //     #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
+    //     /*==== use exp() and sin() ====*/
+    //     #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
+    //     #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
+#endif
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 
-/* serial.c configuration for split keyboard */
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
-#define SOFT_SERIAL_PIN D0
+//#define MATRIX_HAS_GHOST
 
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-#define BACKLIGHT_PIN E6
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
-#define BACKLIGHT_LEVELS 5
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
 
-/* ws2812 RGB LED */
+/*
-#define RGB_DI_PIN D6
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
 
-#define RGBLED_NUM 12    // Number of LEDs
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+/* defined by default; to change, uncomment and set to the combination you want */
+// #define IS_COMMAND() (get_mods() == MOD_MASK_SHIFT)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP           H
+//#define MAGIC_KEY_HELP_ALT       SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER0_ALT     GRAVE
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     B
+//#define MAGIC_KEY_BOOTLOADER_ALT ESC
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_EEPROM_CLEAR   BSPACE
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+#define MOUSEKEY_DELAY             150
+#define MOUSEKEY_INTERVAL          20
+#define MOUSEKEY_MAX_SPEED         10
+#define MOUSEKEY_TIME_TO_MAX       10
+#define MOUSEKEY_WHEEL_MAX_SPEED   8
+#define MOUSEKEY_WHEEL_TIME_TO_MAX 40
 
 /*
  * Feature disable options
@@ -83,4 +201,57 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 //#define NO_ACTION_MACRO
 //#define NO_ACTION_FUNCTION
 
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+/*
+ * HD44780 LCD Display Configuration
+ */
+/*
+#define LCD_LINES           2     //< number of visible lines of the display
+#define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
+
+#define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
+
+#if LCD_IO_MODE
+#define LCD_PORT         PORTB        //< port for the LCD lines
+#define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
+#define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
+#define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
+#define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
+#define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
+#define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
+#define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
+#define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
+#define LCD_RS_PORT      LCD_PORT     //< port for RS line
+#define LCD_RS_PIN       3            //< pin  for RS line
+#define LCD_RW_PORT      LCD_PORT     //< port for RW line
+#define LCD_RW_PIN       2            //< pin  for RW line
+#define LCD_E_PORT       LCD_PORT     //< port for Enable line
+#define LCD_E_PIN        1            //< pin  for Enable line
 #endif
+*/
+
+/* Bootmagic Lite key configuration */
+// #define BOOTMAGIC_LITE_ROW 0
+// #define BOOTMAGIC_LITE_COLUMN 0

keyboards/qwertyydox/info.json

@@ -5,12 +5,66 @@
   "url": "",
   "maintainer": "qmk",
   "processor": "atmega32u4",
-  "width": 16,
+  "width": 16.25,
   "height": 5,
   "layouts": {
     "LAYOUT": {
       "key_count": 53,
-      "layout": [{"label":"L00", "x":0, "y":0.375}, {"label":"L01", "x":1, "y":0.25}, {"label":"L02", "x":2, "y":0.125}, {"label":"L03", "x":3, "y":0}, {"label":"L04", "x":4, "y":0.125}, {"label":"L05", "x":5, "y":0.25}, {"label":"L06", "x":6, "y":0.5}, {"label":"R00", "x":9, "y":0.5}, {"label":"R01", "x":10, "y":0.25}, {"label":"R02", "x":11, "y":0.125}, {"label":"R03", "x":12, "y":0}, {"label":"R04", "x":13, "y":0.125}, {"label":"R05", "x":14, "y":0.25}, {"label":"R06", "x":15, "y":0.375}, {"label":"L10", "x":0, "y":1.375}, {"label":"L11", "x":1, "y":1.25}, {"label":"L12", "x":2, "y":1.125}, {"label":"L13", "x":3, "y":1}, {"label":"L14", "x":4, "y":1.125}, {"label":"L15", "x":5, "y":1.25}, {"label":"L16", "x":6, "y":1.5}, {"label":"R10", "x":9, "y":1.5}, {"label":"R11", "x":10, "y":1.25}, {"label":"R12", "x":11, "y":1.125}, {"label":"R13", "x":12, "y":1}, {"label":"R14", "x":13, "y":1.125}, {"label":"R15", "x":14, "y":1.25}, {"label":"R16", "x":15, "y":1.375}, {"label":"L20", "x":0, "y":2.375}, {"label":"L21", "x":1, "y":2.25}, {"label":"L22", "x":2, "y":2.125}, {"label":"L23", "x":3, "y":2}, {"label":"L24", "x":4, "y":2.125}, {"label":"L25", "x":5, "y":2.25}, {"label":"L26", "x":6.5, "y":3}, {"label":"R20", "x":8.5, "y":3}, {"label":"R21", "x":10, "y":2.25}, {"label":"R22", "x":11, "y":2.125}, {"label":"R23", "x":12, "y":2}, {"label":"R24", "x":13, "y":2.125}, {"label":"R25", "x":14, "y":2.25}, {"label":"R26", "x":15, "y":2.375}, {"label":"L30", "x":0, "y":3.375}, {"label":"L31", "x":1, "y":3.25}, {"label":"L32", "x":2, "y":3.125}, {"label":"L33", "x":3, "y":3}, {"label":"L34", "x":5.5, "y":4}, {"label":"L35", "x":6.5, "y":4}, {"label":"R30", "x":8.5, "y":4}, {"label":"R31", "x":9.5, "y":4}, {"label":"R32", "x":12, "y":3}, {"label":"R33", "x":13, "y":3.125}, {"label":"R34", "x":14, "y":3.25}, {"label":"R35", "x":15, "y":3.375}]
+      "layout": [
+        {"label":"Tab", "x":0, "y":0},
+        {"label":"Q", "x":1, "y":0},
+        {"label":"W", "x":2, "y":0},
+        {"label":"E", "x":3, "y":0},
+        {"label":"R", "x":4, "y":0},
+        {"label":"T", "x":5, "y":0},
+        {"label":"Y", "x":6, "y":0},
+        {"label":"Y", "x":9, "y":0},
+        {"label":"U", "x":10, "y":0},
+        {"label":"I", "x":11, "y":0},
+        {"label":"O", "x":12, "y":0},
+        {"label":"P", "x":13, "y":0},
+        {"label":"{", "x":14, "y":0},
+        {"label":"}", "x":15, "y":0},
+        {"label":"Caps Lock", "x":0.25, "y":1},
+        {"label":"A", "x":1.25, "y":1},
+        {"label":"S", "x":2.25, "y":1},
+        {"label":"D", "x":3.25, "y":1},
+        {"label":"F", "x":4.25, "y":1},
+        {"label":"G", "x":5.25, "y":1},
+        {"label":"H", "x":9.25, "y":1},
+        {"label":"J", "x":10.25, "y":1},
+        {"label":"K", "x":11.25, "y":1},
+        {"label":"L", "x":12.25, "y":1},
+        {"label":":", "x":13.25, "y":1},
+        {"label":"\"", "x":14.25, "y":1},
+        {"label":"|", "x":15.25, "y":1},
+        {"label":"Shift", "x":0.75, "y":2},
+        {"label":"Z", "x":1.75, "y":2},
+        {"label":"X", "x":2.75, "y":2},
+        {"label":"C", "x":3.75, "y":2},
+        {"label":"V", "x":4.75, "y":2},
+        {"label":"B", "x":5.75, "y":2},
+        {"label":"N", "x":9.75, "y":2},
+        {"label":"M", "x":10.75, "y":2},
+        {"label":"<", "x":11.75, "y":2},
+        {"label":">", "x":12.75, "y":2},
+        {"label":"?", "x":13.75, "y":2},
+        {"label":"Shift", "x":14.75, "y":2},
+        {"label":"Ctrl", "x":0.75, "y":3},
+        {"label":"GUI", "x":1.75, "y":3},
+        {"label":"Alt", "x":2.75, "y":3},
+        {"label":"\"-QWERTY\"", "x":3.75, "y":3},
+        {"label":"Enter", "x":4.75, "y":3.33},
+        {"label":"Delete", "x":5.75, "y":3.67},
+        {"label":"TO(_NUM)", "x":6.75, "y":4},
+        {"label":"TO(_NAV)", "x":8.75, "y":4},
+        {"label":"Space", "x":9.75, "y":3.67},
+        {"label":"Back Space", "x":10.75, "y":3.33},
+        {"label":"Left", "x":11.75, "y":3},
+        {"label":"Alt", "x":12.75, "y":3},
+        {"label":"GUI", "x":13.75, "y":3},
+        {"label":"Ctrl", "x":14.75, "y":3}
+      ]
     }
   }
 }

keyboards/qwertyydox/keymaps/default/config.h

@@ -27,17 +27,3 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 // #define MASTER_LEFT
 #define MASTER_RIGHT
 // #define EE_HANDS
-
-#undef RGBLED_NUM
-#define RGBLIGHT_ANIMATIONS
-#define RGBLED_NUM 12
-#define RGBLIGHT_HUE_STEP 8
-#define RGBLIGHT_SAT_STEP 8
-#define RGBLIGHT_VAL_STEP 8
-
-#define MOUSEKEY_DELAY             150
-#define MOUSEKEY_INTERVAL          20
-#define MOUSEKEY_MAX_SPEED         10
-#define MOUSEKEY_TIME_TO_MAX       10
-#define MOUSEKEY_WHEEL_MAX_SPEED   8
-#define MOUSEKEY_WHEEL_TIME_TO_MAX 40

keyboards/qwertyydox/keymaps/default/keymap.c

@@ -2,9 +2,12 @@
 
 extern keymap_config_t keymap_config;
 
-#define _QWERTY 0
+enum layer_names {
-#define _NUM 1
+    _QWERTY,
-#define _NAV 2
+    _NUM,
+    _NAV
+};
+
 enum custom_keycodes {
   qwerty = SAFE_RANGE,
   nav,
@@ -12,17 +15,6 @@ enum custom_keycodes {
   EQL
 };
 
-// #define KC_ KC_TRNS
-#define __ KC_NO
-#define NAV TO(2)
-#define NUM TO(1)
-#define ALPHA TO(0)
-#define NPLUS KC_KP_PLUS
-#define NMINUS KC_KP_MINUS
-#define NSTAR KC_KP_ASTERISK
-#define NSLASH KC_KP_SLASH
-
-
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
   [_QWERTY] = LAYOUT(
@@ -31,33 +23,33 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   //|--------+--------+--------+--------+--------+--------+--------|        |--------+--------+--------+--------+--------+--------+--------|
      KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,                      KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_BSLS,
   //|--------+--------+--------+--------+--------+--------+--------|        |--------+--------+--------+--------+--------+--------+--------|
-     KC_LSPO, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,                  __,           KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSPC,
+     KC_LSPO, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,                               KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSPC,
   //|--------+--------+--------+--------+--------+--------+--------|        |--------+--------+--------+--------+--------+--------+--------|
-     KC_LCTL, KC_LGUI, KC_LALT, qwerty,  KC_ENT,  KC_DEL,  NUM,              NAV,   KC_SPC,  KC_BSPC, KC_LEFT, KC_RALT, KC_RGUI, KC_RCTL
+     KC_LCTL, KC_LGUI, KC_LALT, qwerty,  KC_ENT,  KC_DEL,  TO(1),            TO(2),   KC_SPC,  KC_BSPC, KC_LEFT, KC_RALT, KC_RGUI, KC_RCTL
   //`--------+--------+--------+--------+--------+--------+--------/        \--------+--------+--------+--------+--------+--------+--------'
   ),
 
   [_NUM] = LAYOUT(
   //,--------+--------+--------+--------+--------+--------+--------.        ,--------+--------+--------+--------+--------+--------+--------.
-      KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,            KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12, KC_PSCR, KC_NO,
+     KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,            KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_PSCR, KC_NO,
   //|--------+--------+--------+--------+--------+--------+--------|        |--------+--------+--------+--------+--------+--------+--------|
-      KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,                       KC_7,  KC_8,    KC_9,    KC_0,   KC_MINS,  KC_EQL,   KC_NO,
+     KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,                      KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_NO,
   //|--------+--------+--------+--------+--------+--------+--------|        |--------+--------+--------+--------+--------+--------+--------|
-     KC_LSFT, KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,                 __,           KC_NO,  KC_PPLS, KC_PMNS,  EQL,    KC_PAST, KC_PSLS,
+     KC_LSFT, KC_NO,   KC_NO,   KC_NO,   KC_NO,   KC_NO,                              KC_NO,   KC_PPLS, KC_PMNS, EQL,     KC_PAST, KC_PSLS,
   //|--------+--------+--------+--------+--------+--------+--------|        |--------+--------+--------+--------+--------+--------+--------|
-     KC_LCTL,  KC_ESC, KC_NO,    num,    KC_ENT,  KC_LSFT,  NAV,              ALPHA,   KC_SPC,  KC_BSPC, KC_LEFT, KC_RALT, KC_RGUI, KC_RCTL
+     KC_LCTL,  KC_ESC, KC_NO,   num,     KC_ENT,  KC_LSFT, TO(2),            TO(0),   KC_SPC,  KC_BSPC, KC_LEFT, KC_RALT, KC_RGUI, KC_RCTL
   //`--------+--------+--------+--------+--------+--------+--------/        \--------+--------+--------+--------+--------+--------+--------'
   ),
 
     [_NAV] = LAYOUT(
   //,--------+--------+--------+--------+--------+--------+--------.        ,--------+--------+--------+--------+--------+--------+--------.
-     KC_ESC,   KC_NO,  KC_ACL0, KC_ACL1, KC_ACL2,  KC_WH_L, KC_WH_R,          KC_ESC,   KC_NO,   KC_UP,   NSLASH,  NSTAR,   NMINUS,  NPLUS,
+     KC_ESC,  KC_NO,   KC_ACL0, KC_ACL1, KC_ACL2, KC_WH_L, KC_WH_R,          KC_ESC,  KC_NO,   KC_UP,   KC_PSLS, KC_PAST, KC_PMNS, KC_PPLS,
   //|--------+--------+--------+--------+--------+--------+--------|        |--------+--------+--------+--------+--------+--------+--------|
-     KC_NO,   KC_Z,    KC_X,    KC_C,    KC_V,    KC_WH_U,                     KC_NO,  KC_LEFT, KC_DOWN, KC_RIGHT,KC_NO,   KC_NO,   KC_NO,
+     KC_NO,   KC_Z,    KC_X,    KC_C,    KC_V,    KC_WH_U,                   KC_NO,   KC_LEFT, KC_DOWN, KC_RGHT, KC_NO,   KC_NO,   KC_NO,
   //|--------+--------+--------+--------+--------+--------+--------|        |--------+--------+--------+--------+--------+--------+--------|
-     KC_INS,  KC_HOME, KC_PGUP, KC_BTN1, KC_BTN2,  KC_WH_D,              __,          KC_MS_L, KC_MS_U, KC_MS_D, KC_MS_R,  KC_NO,  KC_NO,
+     KC_INS,  KC_HOME, KC_PGUP, KC_BTN1, KC_BTN2, KC_WH_D,                            KC_MS_L, KC_MS_U, KC_MS_D, KC_MS_R, KC_NO,   KC_NO,
   //|--------+--------+--------+--------+--------+--------+--------|        |--------+--------+--------+--------+--------+--------+--------|
-     KC_DEL,  KC_END,  KC_PGDN,  nav,    KC_LCTL, KC_SPC,  ALPHA,            NUM,    KC_LSFT,   KC_BSPC, KC_NO,   KC_NO,   KC_NO,   RESET
+     KC_DEL,  KC_END,  KC_PGDN, nav,     KC_LCTL, KC_SPC,  TO(0),            TO(1),   KC_LSFT, KC_BSPC, KC_NO,   KC_NO,   KC_NO,   RESET
   //`--------+--------+--------+--------+--------+--------+--------/        \--------+--------+--------+--------+--------+--------+--------'
   )
 };

keyboards/qwertyydox/qwertyydox.h

@@ -1,24 +1,7 @@
-#ifndef QWERTYYDOX_H
+#pragma once
-#define QWERTYYDOX_H
+
+#include "quantum.h"
 
 #ifdef KEYBOARD_qwertyydox_rev1
     #include "rev1.h"
 #endif
-
-#include "quantum.h"
-
-// Used to create a keymap using only KC_ prefixed keys
-#define LAYOUT_kc( \
-    L00, L01, L02, L03, L04, L05, L06,       R00, R01, R02, R03, R04, R05, R06, \
-    L10, L11, L12, L13, L14, L15, L16,       R10, R11, R12, R13, R14, R15, R16, \
-    L20, L21, L22, L23, L24, L25, L26,       R20, R21, R22, R23, R24, R25, R26, \
-    L30, L31, L32, L33,      L34, L35,       R30, R31,      R32, R33, R34, R35  \
-    ) \
-    LAYOUT( \
-        KC_##L00, KC_##L01, KC_##L02, KC_##L03, KC_##L04, KC_##L05, KC_##L06,       KC_##R00, KC_##R01, KC_##R02, KC_##R03, KC_##R04, KC_##R05, KC_##R06, \
-        KC_##L10, KC_##L11, KC_##L12, KC_##L13, KC_##L14, KC_##L15, KC_##L16,       KC_##R10, KC_##R11, KC_##R12, KC_##R13, KC_##R14, KC_##R15, KC_##R16, \
-        KC_##L20, KC_##L21, KC_##L22, KC_##L23, KC_##L24, KC_##L25, KC_##L26,       KC_##R20, KC_##R21, KC_##R22, KC_##R23, KC_##R24, KC_##R25, KC_##R26, \
-        KC_##L30, KC_##L31, KC_##L32, KC_##L33,           KC_##L34, KC_##L35,       KC_##R30, KC_##R31,           KC_##R32, KC_##R33, KC_##R34, KC_##R35  \
-    )
-
-#endif

keyboards/qwertyydox/rev1/config.h

@@ -15,72 +15,4 @@ You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 
-#ifndef REV1_CONFIG_H
+#pragma once
-#define REV1_CONFIG_H
-
-#include QMK_KEYBOARD_CONFIG_H
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID       0xCEEB
-#define PRODUCT_ID      0x1256
-#define DEVICE_VER      0x0100
-#define MANUFACTURER    AYDENandDAD
-#define PRODUCT         QWERTYdox Keyboard
-#define DESCRIPTION     Split 40 percent keyboard
-
-/* key matrix size */
-// Rows are doubled-up
-#define MATRIX_ROWS 8
-#define MATRIX_COLS 7
-
-// wiring of each half
-#define MATRIX_ROW_PINS { B6, B2, B3, B1 }
-#define MATRIX_COL_PINS { F7, F6, F5, C6, D7, D4, D1 }
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
-/* define if matrix has ghost */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-// #define BACKLIGHT_LEVELS 3
-
-/* Set 0 if debouncing isn't needed */
-#define DEBOUNCE 5
-
-/* serial.c configuration for split keyboard */
-#define SOFT_SERIAL_PIN D0
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
-
-#define BACKLIGHT_PIN E6
-#define BACKLIGHT_LEVELS 5
-
-/* ws2812 RGB LED */
-#define RGB_DI_PIN D6
-
-#define RGBLED_NUM 12    // Number of LEDs
-
-/*
- * Feature disable options
- *  These options are also useful to firmware size reduction.
- */
-
-/* disable debug print */
-// #define NO_DEBUG
-
-/* disable print */
-// #define NO_PRINT
-
-/* disable action features */
-//#define NO_ACTION_LAYER
-//#define NO_ACTION_TAPPING
-//#define NO_ACTION_ONESHOT
-//#define NO_ACTION_MACRO
-//#define NO_ACTION_FUNCTION
-
-#endif

keyboards/qwertyydox/rev1/rev1.h

@@ -1,12 +1,7 @@
-#ifndef REV1_H
+#pragma once
-#define REV1_H
 
 #include "qwertyydox.h"
 
-//void promicro_bootloader_jmp(bool program);
-#include "quantum.h"
-
-
 #ifdef USE_I2C
 #include <stddef.h>
 #ifdef __AVR__
@@ -15,12 +10,10 @@
 #endif
 #endif
 
-//void promicro_bootloader_jmp(bool program);
-
 #define LAYOUT( \
     L00, L01, L02, L03, L04, L05, L06,       R00, R01, R02, R03, R04, R05, R06, \
     L10, L11, L12, L13, L14, L15,            R10, R11, R12, R13, R14, R15, R16, \
-    L20, L21, L22, L23, L24, L25,            R20, R21, R22, R23, R24, R25, R26, \
+    L20, L21, L22, L23, L24, L25,                 R21, R22, R23, R24, R25, R26, \
     L30, L31, L32, L33, L34, L35, L36,       R30, R31, R32, R33, R34, R35, R36 \
     ) \
     { \
@@ -30,8 +23,6 @@
         { L30, L31, L32, L33, L34, L35, L36 }, \
         { R06, R05, R04, R03, R02, R01, R00 }, \
         { R16, R15, R14, R13, R12, R11, R10 }, \
-        { R26, R25, R24, R23, R22, R21, R20, }, \
+        { R26, R25, R24, R23, R22, R21, KC_NO, }, \
         { R36, R35, R34, R33, R32, R31, R30 } \
     }
-
-#endif

keyboards/qwertyydox/rev1/rules.mk

@@ -1 +0,0 @@
-BACKLIGHT_ENABLE = no

keyboards/qwertyydox/rules.mk

@@ -52,14 +52,12 @@ EXTRAKEY_ENABLE = no       # Audio control and System control(+450)
 CONSOLE_ENABLE = no         # Console for debug(+400)
 COMMAND_ENABLE = no        # Commands for debug and configuration
 NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
+BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
 MIDI_ENABLE = no            # MIDI controls
 AUDIO_ENABLE = no           # Audio output on port C6
 UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight.
-SUBPROJECT_rev1 = yes
-USE_I2C = yes               # I2C is used between the sides
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
 

keyboards/rgbkb/sol/keymaps/default/keymap.c

@@ -300,7 +300,7 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) {
 #ifdef OLED_DRIVER_ENABLE
 oled_rotation_t oled_init_user(oled_rotation_t rotation) {
   if (is_keyboard_master())
-    return OLED_ROTATION_90;
+    return OLED_ROTATION_270;
   return rotation;
 }
 

keyboards/tanuki/keymaps/default/keymap.c

@@ -1,140 +1,120 @@
 #include QMK_KEYBOARD_H
 
-//Layer definitions
+// custom type to store stuff in EEPROM
+typedef union {
+    uint32_t raw;
+    struct {
+        bool layer_rgb :1;
+    };
+} user_config_t;
+
+user_config_t user_config;
+
+// Layer definitions
 #define _BL 0
 #define _DL 1
 #define _UL 2
 #define _GL 3
 #define _BK 4
 
-
+// Custom keycode to toggle normal RGB or per-layer RGB
-//other variables
+enum custom_keycodes {
-int mCalled = 0;
+    CUSTRGB = SAFE_RANGE,
-bool blockToggle = false;
+};
-bool lRGB = true;
 
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 
 [_BL] = LAYOUT(
-  KC_ESC,   KC_Q,     KC_W,     KC_E,     KC_R,    KC_T,     KC_Y,           KC_U,           KC_I,    KC_O,    KC_P,    KC_BSPC, \
+    KC_ESC,   KC_Q,     KC_W,     KC_E,    KC_R,    KC_T,     KC_Y,       KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC, \
-  KC_TAB,   KC_A,     KC_S,     KC_D,     KC_F,    KC_G,     KC_H,           KC_J,           KC_K,    KC_L,    KC_SCLN, TG(_GL), \
+    KC_TAB,   KC_A,     KC_S,     KC_D,    KC_F,    KC_G,     KC_H,       KC_J,    KC_K,    KC_L,    KC_SCLN, TG(_GL), \
-  KC_LSFT,  KC_Z,     KC_X,     KC_C,    KC_V,     KC_B,           KC_N,           KC_M,    KC_QUOT, KC_SLSH, KC_ENT,  \
+    KC_LSFT,  KC_Z,     KC_X,     KC_C,    KC_V,    KC_B,     KC_N,       KC_M,    KC_QUOT, KC_SLSH, KC_ENT,  \
-  KC_LCTL,  KC_LALT, KC_COMMA, LT(_DL,KC_SPC), LT(_UL,KC_SPC),          KC_DOT,  KC_LGUI),
+    KC_LCTL,  KC_LALT,  KC_COMMA, LT(_DL,KC_SPC), LT(_UL,KC_SPC),         KC_DOT,  KC_LGUI),
 
 [_DL] = LAYOUT(
-  KC_F1,    KC_F2,    KC_F3,    KC_F4,    KC_F5,    KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,   KC_F11,  KC_F12,\
+    KC_F1,    KC_F2,    KC_F3,    KC_F4,    KC_F5,    KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,   KC_F11,  KC_F12,\
-  KC_TRNS,  KC_1,     KC_2,     KC_3,     KC_4,     KC_5,     KC_6,     KC_7,     KC_8,     KC_9,     KC_0,    KC_TRNS,\
+    KC_TRNS,  KC_1,     KC_2,     KC_3,     KC_4,     KC_5,     KC_6,     KC_7,     KC_8,     KC_9,     KC_0,    KC_TRNS,\
-  KC_TRNS,  KC_PSCR,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  \
+    KC_TRNS,  KC_PSCR,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  \
-  KC_TRNS,  RESET,    KC_TRNS,  KC_TRNS,  KC_TRNS,            KC_TRNS,  KC_TRNS),
+    KC_TRNS,  RESET,    KC_TRNS,  KC_TRNS,  KC_TRNS,            KC_TRNS,  KC_TRNS),
 
 [_UL] = LAYOUT(
-  KC_GRV,   KC_LBRC,  KC_RBRC,  KC_LCBR,  KC_RCBR,  KC_PIPE,  KC_BSLS,  KC_PLUS,  KC_UNDS,  KC_MINS,  KC_EQL,  KC_DEL,\
+    KC_GRV,   KC_LBRC,  KC_RBRC,  KC_LCBR,  KC_RCBR,  KC_PIPE,  KC_BSLS,  KC_PLUS,  KC_UNDS,  KC_MINS,  KC_EQL,  KC_DEL,\
-  KC_TRNS,  KC_EXLM,  KC_AT,    KC_HASH,  KC_DLR,   KC_PERC,  KC_CIRC,  KC_AMPR,  KC_ASTR,  KC_LPRN,  KC_RPRN, KC_TRNS, \
+    KC_TRNS,  KC_EXLM,  KC_AT,    KC_HASH,  KC_DLR,   KC_PERC,  KC_CIRC,  KC_AMPR,  KC_ASTR,  KC_LPRN,  KC_RPRN, KC_TRNS, \
-  KC_TRNS,  KC_FN0,   RGB_TOG,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  RGB_SAD,  RGB_VAD,  KC_TRNS,  KC_TRNS,  \
+    KC_TRNS,  CUSTRGB,  RGB_TOG,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  RGB_SAD,  RGB_VAD,  KC_TRNS,  KC_TRNS,  \
-  KC_TRNS,  RGB_MOD,  RGB_HUI,  KC_TRNS,  KC_TRNS,            RGB_SAI,  RGB_VAI),
+    KC_TRNS,  RGB_MOD,  RGB_HUI,  KC_TRNS,  KC_TRNS,            RGB_SAI,  RGB_VAI),
 
 [_GL] = LAYOUT(
-  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_UP,    KC_TRNS,  KC_TRNS, \
+    KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_UP,    KC_TRNS,  KC_TRNS, \
-  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_LEFT,  KC_DOWN,  KC_RGHT,  KC_TRNS, \
+    KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_LEFT,  KC_DOWN,  KC_RGHT,  KC_TRNS, \
-  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  \
+    KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  \
-  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_SPC,   KC_SPC,             KC_TRNS,  KC_TRNS),
+    KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_SPC,   KC_SPC,             KC_TRNS,  KC_TRNS)
-
+  
-[_BK] = LAYOUT(
-  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,\
-  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,\
-  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_NO,    KC_NO,    KC_TRNS,  KC_TRNS,  \
-  KC_TRNS,  KC_NO,    KC_NO,    KC_TRNS,  KC_FN1,  KC_NO,    KC_NO),
-
 };
 
-
+void keyboard_post_init_user(void) {
-//KC_MPLY,  KC_VOLU,  KC_VOLD,  KC_TRNS,  KC_TRNS,            KC_MNXT,  KC_MPRV
+    user_config.raw = eeconfig_read_user();
-//function to toggle the interactive rgb variable
+    if(user_config.layer_rgb) {
-bool toggleLayerRGB(void){
+        rgblight_enable_noeeprom();
-	if(lRGB == true){
+        rgblight_mode_noeeprom(1);
-	return false;
+        rgblight_sethsv_noeeprom(0,10,255);
-	}
+    }
-	else{
-	return true;
-	}
 }
 
-void matrix_init_user(void){
+uint32_t layer_state_set_user(uint32_t state) {
-	rgblight_enable();
+    // This code switches underglow color by active layer, if the user has enabled the feature
-  	rgblight_mode(1);
+    if(user_config.layer_rgb) {
-	rgblight_sethsv(0,10,255);
+        switch (biton32(state)) {
+            case _BL:
+                rgblight_sethsv_noeeprom(0,10,255);
+                rgblight_mode_noeeprom(1);
+                break;
+            case _DL:
+                rgblight_sethsv_noeeprom(130,200,255);
+                rgblight_mode_noeeprom(1);
+                break;
+            case _UL:
+                rgblight_sethsv_noeeprom(170,200,255);
+                rgblight_mode_noeeprom(1);
+                break;
+            case _GL:
+                rgblight_sethsv_noeeprom(0,180,255);
+                rgblight_mode_noeeprom(1);
+                break;
+        }
+    }
+    return state;
 }
 
-//check for layer and if there was a keypress change underglow lighting
-void matrix_scan_kb(void){
-	if(lRGB == true)
-	{
-
-
-
-		//base layer
-		if(layer_state == 0x00000000 && mCalled == 1 ){
-			rgblight_sethsv(0,10,255);
-			mCalled = 0;
-		}
-
-		//down layer
-		else if(layer_state == 0x00000002 && mCalled == 1){
-			rgblight_sethsv(160,255,255);
-			mCalled = 0;
-		}
-
-
-		//up layer with rgb access blocked
-		else if(layer_state == 0x00000004 && mCalled == 1 && lRGB == true){
-			//blockToggle = true;
-			layer_state = 0x00000014;
-			rgblight_sethsv(180,255,255);
-			mCalled = 0;
-		}
-
-		//arrow cluster layer
-		else if(layer_state == 0x00000008 && mCalled == 1){
-			rgblight_sethsv(0,180,255);
-			mCalled = 0;
-		}
-
-		//if on blocked layer and the spacebar has been released reset to baselayer and set colours to white
-		else if(layer_state == 0x00000014 && blockToggle == true )
-		{
-			blockToggle = false;
-			layer_state = 0x00000000;
-			rgblight_sethsv(0,10,255);
-		}
-
-	}
-}
-
-//set mCalled to 1 when a button is pressed to make sure the leds aren't continuesly updated.
 bool process_record_user (uint16_t keycode, keyrecord_t *record) {
-  mCalled = 1;
+    switch (keycode) {
+        case CUSTRGB: // if the user toggled per-layer RGB, update the config and refresh the RGB color
+            if(record->event.pressed) {
+                user_config.layer_rgb ^= 1;
+                eeconfig_update_user(user_config.raw);
+                if (user_config.layer_rgb) {
+                    layer_state_set(layer_state);
+                }
+            }
+            return false;
+            break;
+        case RGB_MOD:
+        case RGB_SAD:
+        case RGB_SAI:
+        case RGB_HUI:
+        case RGB_VAD:
+        case RGB_VAI:
+            if(user_config.layer_rgb && record->event.pressed) {
+                return false; // if layer RGB is on, ignore attempts to change RGB settings
+            }
+            break;
+    }
+    return true;
+}
 
-  //uncommenting the line below causes the lights to flicker when typing on the keyboard.
+void eeconfig_init_user(void) { // in case EEPROM is reset, set up our custom config
-  //rgblight_sethsv(0,255,0);
+    user_config.raw = 0;
-
+    user_config.layer_rgb = true; // enable per-layer RGB by default
-	if(keycode == KC_FN0 && record->event.pressed){
+    eeconfig_update_user(user_config.raw);
-		//set the toggle and make sure to set the colour back to white
+    rgblight_enable();
-		lRGB = toggleLayerRGB();
+    rgblight_sethsv(0,10,255);
-		rgblight_enable();
+    rgblight_mode(1);
-  		rgblight_mode(1);
-		rgblight_sethsv(0,255,255);
-		layer_state =0x00000000;
-
-		return false;
-	}
-
-	//check if spacebar is released when on a different layer
-	if(keycode == KC_FN1){
-		if(record ->event.pressed){
-		}else{
-		blockToggle = true;
-		}
-	}
-
-  return true;
 }

keyboards/wilba_tech/wt60_d/config.h

@@ -0,0 +1,200 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0x6582 // wilba.tech
+#define PRODUCT_ID      0x060D // 60-D
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    wilba.tech
+#define PRODUCT         wilba.tech WT60-D
+#define DESCRIPTION     wilba.tech WT60-D
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 14
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { E6, F0, F4, F6, F7 }
+#define MATRIX_COL_PINS { F5, D5, D3, D2, B7, B0, B3, C7, C6, B6, B5, B4, D7, D6 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL*/
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCE 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
+ * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
+ */
+// #define GRAVE_ESC_CTRL_OVERRIDE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+   - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+   - MIDI notes can be added to the keymap
+   - Octave shift and transpose
+   - Virtual sustain, portamento, and modulation wheel
+   - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+#define DYNAMIC_KEYMAP_LAYER_COUNT 4
+
+// EEPROM usage
+
+// TODO: refactor with new user EEPROM code (coming soon)
+#define EEPROM_MAGIC 0x451F
+#define EEPROM_MAGIC_ADDR 32
+// Bump this every time we change what we store
+// This will automatically reset the EEPROM with defaults
+// and avoid loading invalid data from the EEPROM
+#define EEPROM_VERSION 0x08
+#define EEPROM_VERSION_ADDR 34
+
+// Dynamic keymap starts after EEPROM version
+#define DYNAMIC_KEYMAP_EEPROM_ADDR 35
+// Dynamic macro starts after dynamic keymaps (35+(4*5*14*2)) = (35+560)
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 595
+#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 429
+#define DYNAMIC_KEYMAP_MACRO_COUNT 16

keyboards/wilba_tech/wt60_d/info.json

@@ -0,0 +1,13 @@
+{
+    "keyboard_name": "wilba.tech WT60-D", 
+    "url": "https://wilba.tech", 
+    "maintainer": "Wilba", 
+    "bootloader": "atmel-dfu", 
+    "width": 15, 
+    "height": 5, 
+    "layouts": {
+        "LAYOUT_all": {
+            "layout": [{"label":"~", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"Menu", "x":12.5, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":4, "w":1.25}]
+        }
+    }
+}

keyboards/wilba_tech/wt60_d/keymaps/default/keymap.c

@@ -0,0 +1,38 @@
+// Default layout for WT60-D
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+// Default layer
+[0] = LAYOUT_all(
+	KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_DEL,
+	KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,
+	KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
+	KC_LSFT, KC_NO,   KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT, MO(1),
+	KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, KC_RGUI, MO(1),   KC_RCTL),
+
+// Fn1 Layer
+[1] = LAYOUT_all(
+	KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  KC_TRNS,
+	KC_CAPS, KC_TRNS, KC_UP,   KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_INS,  KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_TRNS,
+	KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_HOME, KC_PGUP, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_END,  KC_PGDN, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+// Fn2 Layer
+[2] = LAYOUT_all(
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+// Fn3 Layer
+[3] = LAYOUT_all(
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+};

keyboards/wilba_tech/wt60_d/keymaps/via/keymap.c

@@ -0,0 +1,38 @@
+// Default layout for WT60-D
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+// Default layer
+[0] = LAYOUT_all(
+	KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC, KC_DEL,
+	KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS,
+	KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,
+	KC_LSFT, KC_NO,   KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT, MO(1),
+	KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, KC_RGUI, MO(1),   KC_RCTL),
+
+// Fn1 Layer
+[1] = LAYOUT_all(
+	KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  KC_TRNS,
+	KC_CAPS, KC_TRNS, KC_UP,   KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_INS,  KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_TRNS,
+	KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_HOME, KC_PGUP, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_END,  KC_PGDN, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+// Fn2 Layer
+[2] = LAYOUT_all(
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+// Fn3 Layer
+[3] = LAYOUT_all(
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+	KC_TRNS, KC_TRNS, KC_TRNS,                            KC_TRNS,                            KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS),
+
+};

keyboards/wilba_tech/wt60_d/keymaps/via/rules.mk

@@ -0,0 +1,68 @@
+# project specific files
+SRC =	keyboards/wilba_tech/wt_main.c
+		
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section
+BOOTLOADER = atmel-dfu
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+
+RAW_ENABLE = yes
+DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt60_d/readme.md

@@ -0,0 +1,17 @@
+# wilba.tech WT60-D
+
+![wilba.tech WT60-D](https://cdn.shopify.com/s/files/1/1347/2157/products/Untitled-5_1800x1800.png?v=1563699242)
+
+WT60-D is a keyboard PCB supporting 60% layout. [More info at wilba.tech](https://wilba.tech/)
+
+First produced as WT60-D MEKANISK for Mekanisk.
+
+Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582)  
+Hardware Supported: wilba.tech WT60-D  
+Hardware Availability: Custom keyboard group buys
+
+Make example for this keyboard (after setting up your build environment):
+
+    make wilba_tech/wt60_d:default
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).

keyboards/wilba_tech/wt60_d/rules.mk

@@ -0,0 +1,68 @@
+# project specific files
+SRC =	keyboards/wilba_tech/wt_main.c
+		
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section
+BOOTLOADER = atmel-dfu
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+
+RAW_ENABLE = yes
+DYNAMIC_KEYMAP_ENABLE = yes

keyboards/wilba_tech/wt60_d/wt60_d.c

@@ -0,0 +1,17 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+// Nothing to see here, move along... ;-)

keyboards/wilba_tech/wt60_d/wt60_d.h

@@ -0,0 +1,35 @@
+/* Copyright 2018 Jason Williams (Wilba)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "quantum.h"
+
+#define ____ KC_NO
+
+#define LAYOUT_all( \
+    K000, K003, K002, K001, K004, K005, K006, K007, K008, K009, K012, K011, K010, K013, K213, \
+    K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113,       \
+    K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212,             \
+    K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313,       \
+    K400, K401, K402,                   K403,                   K410, K411, K412, K413        \
+) { \
+    { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013 }, \
+    { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113 }, \
+    { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213 }, \
+    { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313 }, \
+    { K400, K401, K402, K403, ____, ____, ____, ____, ____, ____, K410, K411, K412, K413 }  \
+}

keyboards/wilba_tech/wt75_a/info.json

@@ -6,7 +6,7 @@
     "width": 16, 
     "height": 6, 
     "layouts": {
-        "LAYOUT": {
+        "LAYOUT_all": {
             "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":1.5, "y":0}, {"label":"F2", "x":2.5, "y":0}, {"label":"F3", "x":3.5, "y":0}, {"label":"F4", "x":4.5, "y":0}, {"label":"F5", "x":5.75, "y":0}, {"label":"F6", "x":6.75, "y":0}, {"label":"F7", "x":7.75, "y":0}, {"label":"F8", "x":8.75, "y":0}, {"label":"F9", "x":10, "y":0}, {"label":"F10", "x":11, "y":0}, {"label":"F11", "x":12, "y":0}, {"label":"F12", "x":13, "y":0}, {"label":"Del", "x":15, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Bksp", "x":13, "y":1.25}, {"label":"Bksp", "x":14, "y":1.25}, {"label":"Home", "x":15, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"|", "x":13.5, "y":2.25, "w":1.5}, {"label":"PgUp", "x":15, "y":2.25}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"\"", "x":11.75, "y":3.25}, {"label":"Enter", "x":12.75, "y":3.25, "w":2.25}, {"label":"PgDn", "x":15, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":2.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":1.75}, {"label":"\u2191", "x":14, "y":4.25}, {"label":"End", "x":15, "y":4.25}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"label":"6.25U", "x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"\u2190", "x":13, "y":5.25}, {"label":"\u2193", "x":14, "y":5.25}, {"label":"\u2192", "x":15, "y":5.25}]
         }
     }

keyboards/wilba_tech/wt75_b/info.json

@@ -6,7 +6,7 @@
     "width": 16, 
     "height": 6, 
     "layouts": {
-        "LAYOUT": {
+        "LAYOUT_all": {
             "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15, "y":0}, {"x":0, "y":1}, {"x":1, "y":1}, {"x":2, "y":1}, {"x":3, "y":1}, {"x":4, "y":1}, {"x":5, "y":1}, {"x":6, "y":1}, {"x":7, "y":1}, {"x":8, "y":1}, {"x":9, "y":1}, {"x":10, "y":1}, {"x":11, "y":1}, {"x":12, "y":1}, {"x":13, "y":1}, {"x":14, "y":1}, {"x":15, "y":1}, {"x":0, "y":2, "w":1.5}, {"x":1.5, "y":2}, {"x":2.5, "y":2}, {"x":3.5, "y":2}, {"x":4.5, "y":2}, {"x":5.5, "y":2}, {"x":6.5, "y":2}, {"x":7.5, "y":2}, {"x":8.5, "y":2}, {"x":9.5, "y":2}, {"x":10.5, "y":2}, {"x":11.5, "y":2}, {"x":12.5, "y":2}, {"x":13.5, "y":2, "w":1.5}, {"x":15, "y":2}, {"x":0, "y":3, "w":1.75}, {"x":1.75, "y":3}, {"x":2.75, "y":3}, {"x":3.75, "y":3}, {"x":4.75, "y":3}, {"x":5.75, "y":3}, {"x":6.75, "y":3}, {"x":7.75, "y":3}, {"x":8.75, "y":3}, {"x":9.75, "y":3}, {"x":10.75, "y":3}, {"x":11.75, "y":3}, {"x":12.75, "y":3, "w":2.25}, {"x":15, "y":3}, {"x":0, "y":4, "w":2.25}, {"x":2.25, "y":4}, {"x":3.25, "y":4}, {"x":4.25, "y":4}, {"x":5.25, "y":4}, {"x":6.25, "y":4}, {"x":7.25, "y":4}, {"x":8.25, "y":4}, {"x":9.25, "y":4}, {"x":10.25, "y":4}, {"x":11.25, "y":4}, {"x":12.25, "y":4, "w":1.75}, {"x":14, "y":4}, {"x":15, "y":4}, {"x":0, "y":5, "w":1.25}, {"x":1.25, "y":5, "w":1.25}, {"x":2.5, "y":5, "w":1.25}, {"x":3.75, "y":5, "w":6.25}, {"x":10, "y":5, "w":1.25}, {"x":11.25, "y":5, "w":1.25}, {"x":13, "y":5}, {"x":14, "y":5}, {"x":15, "y":5}]
         }
     }

layouts/community/ortho_4x12/jotix/keymap.c

@@ -3,17 +3,18 @@
 
 enum layers {
   _QWERTY,
+  _FN,
   _LOWER,
   _RAISE,
-  _UNI_LCK
+  _UNICODE
 };
 
+#define FN      MO(_FN)
 #define LOWER   MO(_LOWER)
 #define RAISE   MO(_RAISE)
-#define UNI_LCK MO(_UNI_LCK)
+#define UNICODE MO(_UNICODE)
 #define TGLOWER TG(_LOWER)
 #define TGRAISE TG(_RAISE)
-#define SHRAISE LM(_RAISE, MOD_LSFT)
 
 static bool is_ctl_pressed;
 static bool is_esc_pressed;
@@ -29,19 +30,31 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
     KC_LSFT, KC_Z  , KC_X  , KC_C  , KC_V  , KC_B  , KC_N  , KC_M  ,KC_COMM, KC_DOT, KC_UP ,KC_SLSH,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    KC_LCTL,KC_LGUI,KC_LALT,UNI_LCK, LOWER , KC_SPC, KC_SPC, RAISE ,SHRAISE,KC_LEFT,KC_DOWN,KC_RGHT
+    KC_LCTL,KC_LGUI,KC_LALT,   FN  , LOWER , KC_SPC, KC_SPC, RAISE ,UNICODE,KC_LEFT,KC_DOWN,KC_RGHT
 // └───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┘
 ), 
 
+[_FN] = LAYOUT_ortho_4x12 (
+// ┌───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┐
+    _______, KC_F1 , KC_F2 , KC_F3 , KC_F4 ,_______,_______,_______,_______,_______,_______,_______,
+// ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
+    _______, KC_F5 , KC_F6 , KC_F7 , KC_F8 ,_______,_______,_______,_______,_______,_______,_______,
+// ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
+    _______, KC_F9 , KC_F10, KC_F11, KC_F12,_______,_______,_______,_______,_______,KC_PGUP,_______,
+// ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
+    _______,_______,_______,_______,TGLOWER,_______,_______,TGRAISE,_______,KC_HOME,KC_PGDN, KC_END
+// └───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┘
+),
+
 [_LOWER] = LAYOUT_ortho_4x12 (
 // ┌───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┐
-    _______, KC_F1 , KC_F2 , KC_F3 , KC_F4 ,_______, KC_INS, KC_P7 , KC_P8 , KC_P9 ,KC_PMNS,_______,
+    _______,  KC_1 ,  KC_2 ,  KC_3 ,  KC_4 ,  KC_5 ,  KC_6 ,  KC_7 ,  KC_8 ,  KC_9 ,  KC_0 ,_______,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______, KC_F5 , KC_F6 , KC_F7 , KC_F8 ,KC_HOME,KC_PGUP, KC_P4 , KC_P5 , KC_P6 ,KC_PPLS,KC_PENT,
+    _______,KC_VOLD,KC_MUTE,KC_VOLU,KC_HOME,KC_PGUP,KC_LBRC,KC_RBRC,KC_BSLS,KC_QUOT,_______,_______,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______, KC_F9 , KC_F10, KC_F11, KC_F12, KC_END,KC_PGDN, KC_P1 , KC_P2 , KC_P3 ,KC_PAST,KC_PSLS,
+    _______,KC_MPRV,KC_MPLY,KC_MNXT, KC_END,KC_PGDN,KC_MINS, KC_EQL,_______,_______,_______,_______,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______,_______,_______,_______,_______,_______,_______,_______, KC_P0 ,KC_PDOT,KC_LPRN,KC_RPRN     
+    _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______
 // └───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┘
 ),
 
@@ -49,7 +62,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 // ┌───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┐
      KC_GRV,  KC_1 ,  KC_2 ,  KC_3 ,  KC_4 ,  KC_5 ,  KC_6 ,  KC_7 ,  KC_8 ,  KC_9 ,  KC_0 , KC_DEL,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    KC_CAPS,_______,_______,_______,_______,_______,KC_LBRC,KC_RBRC,KC_BSLS,KC_QUOT,_______,_______,
+    _______,_______,_______,_______,_______,_______,KC_LBRC,KC_RBRC,KC_BSLS,KC_QUOT,_______,_______,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
     _______,_______,_______,_______,_______,_______,KC_MINS, KC_EQL,_______,_______,KC_VOLU,_______,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
@@ -57,15 +70,15 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 // └───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┘
 ),
 
-[_UNI_LCK] = LAYOUT_ortho_4x12 (
+[_UNICODE] = LAYOUT_ortho_4x12 (
 // ┌───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┬───────┐
-     UN_ESC, UN_Q  , UN_W  , UN_E  , UN_R  , UN_T  , UN_Y  , UN_U  , UN_I  , UN_O  , UN_P  ,_______,
+     UN_ESC, UN_Q  , UN_W  , UN_E  , UN_R  , UN_T  , UN_Y  , UN_U  , UN_I  , UN_O  , UN_P  ,UN_BSPC,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    _______, UN_A  , UN_S  , UN_D  , UN_F  , UN_G  , UN_H  , UN_J  , UN_K  , UN_L  ,UN_SCLN,_______,
+     UN_TAB, UN_A  , UN_S  , UN_D  , UN_F  , UN_G  , UN_H  , UN_J  , UN_K  , UN_L  ,UN_SCLN, UN_ENT,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
     _______, UN_Z  , UN_X  , UN_C  , UN_V  , UN_B  , UN_N  , UN_M  ,UN_COMM, UN_DOT, UN_UP ,UN_SLSH,
 // ├───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┼───────┤
-    UC_M_LN,UC_M_WI,UC_M_OS,_______,TGLOWER,_______,_______,TGRAISE,_______,UN_LEFT,UN_DOWN,UN_RGHT
+    UC_M_LN,UC_M_WI,UC_M_OS,_______,_______,_______,_______,_______,_______,UN_DOWN, UN_UP ,UN_RGHT
 // └───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┴───────┘
 ),
 
@@ -82,7 +95,7 @@ uint32_t layer_state_set_user(uint32_t state) {
     writePinLow(JOTANCK_LED1);
     writePinHigh(JOTANCK_LED2);
     break;
-  case _UNI_LCK:
+  case _FN:
     writePinHigh(JOTANCK_LED1);
     writePinHigh(JOTANCK_LED2);
     break;
@@ -95,11 +108,13 @@ uint32_t layer_state_set_user(uint32_t state) {
   return state;
 }
 
+/*  
 void led_set_user(uint8_t usb_led) {
   if (!(IS_LED_ON(usb_led, USB_LED_NUM_LOCK))) {
     tap_code(KC_NUMLOCK);
   }
 }
+*/
 
 void keyboard_post_init_user(void) {
     set_unicode_input_mode(UC_LNX);
@@ -119,6 +134,7 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) {
   };
   return true;
 }
+
 void matrix_scan_user(void) {
   if (is_ctl_pressed && is_esc_pressed && is_bspc_pressed) {
     reset_keyboard();

layouts/community/ortho_4x12/jotix/unicode.c

@@ -71,6 +71,12 @@ enum unicode_names {
     TREBOL_SUIT,
     HEART_SUIT,
     DIAMOND_SUIT,
+    NARRAY_SUM,
+    INFINIT_SYMBOL,
+    DIAMOND_BULLET,
+    CIRCLE_BULLET,
+    SMILE_FACE,
+    SAD_FACE
 };
 
 const uint32_t PROGMEM unicode_map[] = {
@@ -142,10 +148,16 @@ const uint32_t PROGMEM unicode_map[] = {
     [DIVISION]      = 0x00F7,
     [SQUARE_ROOT]   = 0x221A,
     [CUBE_ROOT]     = 0x221B,
-    [SPADE_SUIT]    = 0x2660, 
+    [SPADE_SUIT]    = 0x2660,
     [TREBOL_SUIT]   = 0x2663,
     [HEART_SUIT]    = 0x2664,
-    [DIAMOND_SUIT]  = 0x2665
+    [DIAMOND_SUIT]  = 0x2665,
+    [NARRAY_SUM]    = 0x2211,
+    [INFINIT_SYMBOL]= 0x221E,
+    [DIAMOND_BULLET]= 0x2B25,
+    [CIRCLE_BULLET] = 0x2981,
+    [SMILE_FACE]    = 0x263A,
+    [SAD_FACE]      = 0x2639
 };
 
 #define UN_ESC  XP(DEGREE, DEGREE_CELCIUS)
@@ -159,6 +171,8 @@ const uint32_t PROGMEM unicode_map[] = {
 #define UN_I    XP(I_ACUTE, I_ACUTEC)
 #define UN_O    XP(O_ACUTE, O_ACUTEC)
 #define UN_P    XP(POUND, PILCROW)
+#define UN_BSPC XP(BOX_CROSS, DBOX_CROSS)
+#define UN_TAB  XP(DIAMOND_BULLET, CIRCLE_BULLET)
 #define UN_A    XP(A_ACUTE, A_ACUTEC)
 #define UN_S    XP(BOX_CORNER_1, DBOX_CORNER_1)
 #define UN_D    XP(BOX_CORNER_2, DBOX_CORNER_2)
@@ -169,8 +183,9 @@ const uint32_t PROGMEM unicode_map[] = {
 #define UN_K    XP(BOX_UNION_3, DBOX_UNION_3)
 #define UN_L    XP(BOX_UNION_4, DBOX_UNION_4)
 #define UN_SCLN XP(BOX_HORIZONTAL, DBOX_HORIZONT)
-#define UN_Z    XP(BOX_VERTICAL, DBOX_VERTICAL)
+#define UN_ENT  XP(BOX_VERTICAL, DBOX_VERTICAL)
-#define UN_X    XP(BOX_CROSS, DBOX_CROSS)
+#define UN_Z    XP(NARRAY_SUM, INFINIT_SYMBOL)
+#define UN_X    XP(SMILE_FACE, SAD_FACE)
 #define UN_C    XP(COPYRIGHT, REGISTERED)
 #define UN_V    XP(SPADE_SUIT, TREBOL_SUIT)
 #define UN_B    XP(HEART_SUIT, DIAMOND_SUIT)

quantum/split_common/matrix.c

@@ -252,6 +252,14 @@ void matrix_init(void) {
 
   // Set pinout for right half if pinout for that half is defined
   if (!isLeftHand) {
+#ifdef DIRECT_PINS_RIGHT
+    const pin_t direct_pins_right[MATRIX_ROWS][MATRIX_COLS] = DIRECT_PINS_RIGHT;
+    for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+      for (uint8_t j = 0; j < MATRIX_COLS; j++) {
+        direct_pins[i][j] = direct_pins_right[i][j];
+      }
+    }
+#endif
 #ifdef MATRIX_ROW_PINS_RIGHT
     const pin_t row_pins_right[MATRIX_ROWS] = MATRIX_ROW_PINS_RIGHT;
     for (uint8_t i = 0; i < MATRIX_ROWS; i++) {