[fix] dfu-programmer <0.7 doesn't support --force flag (#10292 )

Fixes <https://github.com/qmk/qmk_firmware/issues/10286>.
Remove use of sudo in lily58 make docs (#10301 )
2020-09-13 02:17:47 +01:00 · 2020-09-12 20:40:31 +01:00 · 2020-09-12 03:11:30 -07:00 · 2020-09-12 00:55:52 -07:00 · 2020-09-11 18:19:05 -07:00 · 2020-09-11 13:10:30 -07:00
238 changed files with 7000 additions and 1496 deletions
@@ -48,11 +48,12 @@ However, USB cables, SATA cables, and even just 4 wires have been known to be us
 ### Serial Wiring
-The 3 wires of the TRS/TRRS cable need to connect GND, VCC, and D0 (aka PDO or pin 3) between the two Pro Micros. 
+The 3 wires of the TRS/TRRS cable need to connect GND, VCC, and D0/D1/D2/D3 (aka PD0/PD1/PD2/PD3) between the two Pro Micros. 
 ?> Note that the pin used here is actually set by `SOFT_SERIAL_PIN` below.
-![serial wiring](https://i.imgur.com/C3D1GAQ.png)
+<img alt="sk-pd0-connection-mono" src="https://user-images.githubusercontent.com/2170248/92296488-28e9ad80-ef70-11ea-98be-c40cb48a0319.JPG" width="48%"/>
 <img alt="sk-pd2-connection-mono" src="https://user-images.githubusercontent.com/2170248/92296490-2d15cb00-ef70-11ea-801f-5ace313013e6.JPG" width="48%"/>
 ### I<sup>2</sup>C Wiring
@@ -60,7 +61,7 @@ The 4 wires of the TRRS cable need to connect GND, VCC, and SCL and SDA (aka PD0
 The pull-up resistors may be placed on either half. If you wish to use the halves independently, it is also possible to use 4 resistors and have the pull-ups in both halves.
-![I2C wiring](https://i.imgur.com/Hbzhc6E.png)
+<img alt="sk-i2c-connection-mono" src="https://user-images.githubusercontent.com/2170248/92297182-92b98580-ef77-11ea-9d7d-d6033914af43.JPG" width="50%"/>
 ## Firmware Configuration
@@ -1,8 +1,8 @@
 # 分割キーボード
 <!---
-  original document:0.9.43:docs/feature_split_keyboard.md
+  original document:0.10.8:docs/feature_split_keyboard.md
-  git diff 0.9.43 HEAD -- docs/feature_split_keyboard.md | cat
+  git diff 0.10.8 HEAD -- docs/feature_split_keyboard.md | cat
 -->
 QMK ファームウェアリポジトリの多くのキーボードは、"分割"キーボードです。それらは2つのコントローラを使います — 1つは USB に接続し、もう1つは TRRS または同様のケーブルを介してシリアルまたは I<sup>2</sup>C 接続で接続します。
@@ -53,11 +53,12 @@ QMK ファームウェアには、任意のキーボードで使用可能な一
 ### シリアル配線
-2つの Pro Micro 間で GND、Vcc、D0 (別名 PDO あるいは pin 3) を TRS/TRRS ケーブルの3本のワイヤで接続します。
+2つの Pro Micro 間で GND、Vcc、D0/D1/D2/D3 (別名 PD0/PD1/PD2/PD3) を TRS/TRRS ケーブルの3本のワイヤで接続します。
 ?> ここで使われるピンは実際には以下の `SOFT_SERIAL_PIN` によって設定されることに注意してください。
-![シリアル配線](https://i.imgur.com/C3D1GAQ.png)
+<img alt="sk-pd0-connection-mono" src="https://user-images.githubusercontent.com/2170248/92296488-28e9ad80-ef70-11ea-98be-c40cb48a0319.JPG" width="48%"/>
 <img alt="sk-pd2-connection-mono" src="https://user-images.githubusercontent.com/2170248/92296490-2d15cb00-ef70-11ea-801f-5ace313013e6.JPG" width="48%"/>
 ### I<sup>2</sup>C 配線
@@ -65,7 +66,7 @@ QMK ファームウェアには、任意のキーボードで使用可能な一
 プルアップ抵抗はキーボードの左右どちら側にも配置することができます。もし各側を単独で使いたい場合は、4つの抵抗を使い、両側にプルアップ抵抗を配置することもできます。
-![I2C 配線](https://i.imgur.com/Hbzhc6E.png)
+<img alt="sk-i2c-connection-mono" src="https://user-images.githubusercontent.com/2170248/92297182-92b98580-ef77-11ea-9d7d-d6033914af43.JPG" width="50%"/>
 ## ファームウェア設定
@@ -0,0 +1,88 @@
 # 言語固有のキーコード
 <!---
  original document: 0.9.55:docs/reference_keymap_extras.md
  git diff 0.9.55 HEAD -- docs/reference_keymap_extras.md | cat
 -->
 キーボードは多くの言語をサポートすることができます。ただし、それらはキーを押したことで生成される実際の文字を送信しません - 代わりに数字のコードを送信します。USB HID の仕様ではそれらは "usages" と呼ばれますが、キーボードの文脈では「スキャンコード」あるいは「キーコード」と呼ばれることが多いです。
 HID Keyboard/Keypad usage ページでは 256 未満の usage が定義されており、それらの一部は現在のオペレーティングシステムでは機能しません。では、この言語のサポートはどのようにして実現されるのでしょうか？
 簡単に言うと、オペレーティングシステムはユーザが設定したキーボードレイアウトに基づいて受け取った usage を適切な文字にマップします。例えば、スウェーデン人がキーボードの `å` という文字が刻印されたキーを押すと、キーボードは *実際には* `[` のキーコードを送信します。
 明らかにこれは混乱する可能性があるため、QMK は多くのキーボードレイアウトのために言語固有のキーコードのエイリアスを提供します。これらはそれだけでは何もしません - さらに OS の設定で対応するキーボードレイアウトを設定する必要があります。それらをキーマップのキーキャップラベルと考えてください。
 これらを使うには、`keymap.c` で対応する [ヘッダファイル](https://github.com/qmk/qmk_firmware/tree/master/quantum/keymap_extras) を `#include` し、それらで定義されているキーコードを `KC_` プリフィクスの代わりに追加します:
 | レイアウト                  | ヘッダファイル                   |
 |-----------------------------|----------------------------------|
 | Canadian Multilingual (CSA) | `keymap_canadian_multilingual.h` |
 | Croatian                    | `keymap_croatian.h`              |
 | Czech                       | `keymap_czech.h`                 |
 | Danish                      | `keymap_danish.h`                |
 | Dutch (Belgium)             | `keymap_belgian.h`               |
 | English (Ireland)           | `keymap_irish.h`                 |
 | English (UK)                | `keymap_uk.h`                    |
 | English (US International)  | `keymap_us_international.h`      |
 | Estonian                    | `keymap_estonian.h`              |
 | Finnish                     | `keymap_finnish.h`               |
 | French                      | `keymap_french.h`                |
 | French (AFNOR)              | `keymap_french_afnor.h`          |
 | French (BÉPO)               | `keymap_bepo.h`                  |
 | French (Belgium)            | `keymap_belgian.h`               |
 | French (Switzerland)        | `keymap_fr_ch.h`                 |
 | French (macOS, ISO)         | `keymap_french_osx.h`            |
 | German                      | `keymap_german.h`                |
 | German (Switzerland)        | `keymap_german_ch.h`             |
 | German (macOS)              | `keymap_german_osx.h`            |
 | German (Neo2)*              | `keymap_neo2.h`                  |
 | Greek*                      | `keymap_greek.h`                 |
 | Hebrew*                     | `keymap_hebrew.h`                |
 | Hungarian                   | `keymap_hungarian.h`             |
 | Icelandic                   | `keymap_icelandic.h`             |
 | Italian                     | `keymap_italian.h`               |
 | Italian (macOS, ANSI)       | `keymap_italian_osx_ansi.h`      |
 | Italian (macOS, ISO)        | `keymap_italian_osx_iso.h`       |
 | Japanese                    | `keymap_jp.h`                    |
 | Korean                      | `keymap_korean.h`                |
 | Latvian                     | `keymap_latvian.h`               |
 | Lithuanian (ĄŽERTY)         | `keymap_lithuanian_azerty.h`     |
 | Lithuanian (QWERTY)         | `keymap_lithuanian_qwerty.h`     |
 | Norwegian                   | `keymap_norwegian.h`             |
 | Polish                      | `keymap_polish.h`                |
 | Portuguese                  | `keymap_portuguese.h`            |
 | Portuguese (Brazil)         | `keymap_br_abnt2.h`              |
 | Romanian                    | `keymap_romanian.h`              |
 | Russian*                    | `keymap_russian.h`               |
 | Serbian*                    | `keymap_serbian.h`               |
 | Serbian (Latin)             | `keymap_serbian_latin.h`         |
 | Slovak                      | `keymap_slovak.h`                |
 | Slovenian                   | `keymap_slovenian.h`             |
 | Spanish                     | `keymap_spanish.h`               |
 | Spanish (Dvorak)            | `keymap_spanish_dvorak.h`        |
 | Swedish                     | `keymap_swedish.h`               |
 | Turkish (F)                 | `keymap_turkish_f.h`             |
 | Turkish (Q)                 | `keymap_turkish_q.h`             |
 言語固有でないものもありますが、QWERTY レイアウトを使っていない場合に役立ちます:
 | レイアウト          | ヘッダファイル           |
 |---------------------|--------------------------|
 | Colemak             | `keymap_colemak.h`       |
 | Dvorak              | `keymap_dvorak.h`        |
 | Dvorak (French)     | `keymap_dvorak_fr.h`     |
 | Dvorak (Programmer) | `keymap_dvp.h`           |
 | Norman              | `keymap_norman.h`        |
 | Plover*             | `keymap_plover.h`        |
 | Plover (Dvorak)*    | `keymap_plover_dvorak.h` |
 | Steno*              | `keymap_steno.h`         |
 | Workman             | `keymap_workman.h`       |
 | Workman (ZXCVM)     | `keymap_workman_zxcvm.h` |
 ## Sendstring サポート
 デフォルトでは、`SEND_STRING()` は US ANSI キーボードレイアウトが設定されたと見なします。別のレイアウトを使っている場合は、キーマップで(上記のように)`#include "sendstring_*.h"` して、ASCII 文字をキーコードにマッピングするために使われるルックアップテーブルを上書きすることができます。
 ここで注意すべき重要な点は、`SEND_STRING()` は [ASCII 文字](https://en.wikipedia.org/wiki/ASCII#Character_set) でのみ機能するということです。これは、ユニコード文字を含む文字列を渡すことができないことを意味します - 残念ながら、これには希望のレイアウトに存在する可能性のあるアクセント付き文字が含まれています。
 多くのレイアウトでは、Grave または Tilde などの特定の文字を[デッドキー](https://en.wikipedia.org/wiki/Dead_key)としてのみ使えるようにしています。そのため、デッドキーが次の文字と潜在的に結合されることを防ぐためには、送信したい文字列の中のデッドキーのすぐ後にスペースを追加する必要があります。
 ラテン語由来のアルファベットを使わない(例えば、ギリシャ語やロシア語のような)他のレイアウトには、Sendstring ヘッダーがありません。従って ASCII 文字セットのほとんどを入力する方法がありません。これらは上記で `*` でマークされています。
@@ -1,2 +1,4 @@
 VIA_ENABLE = yes
 LTO_ENABLE = yes
 RGB_MATRIX_ENABLE = no
 RGBLIGHT_ENABLE = yes
@@ -0,0 +1,17 @@
 /* Copyright 2020 Koichi Katano
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include "bakeneko65.h"
@@ -0,0 +1,75 @@
 /* Copyright 2020 Koichi Katano
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "quantum.h"
 #define LAYOUT_65_ansi_split_bs( \
    k000, k001, k002, k003, k004, k005, k006, k007, k008, k009, k010, k011, k012, k013, k014, k015, \
    k100, k101, k102, k103, k104, k105, k106, k107, k108, k109, k110, k111, k112,       k113, k115, \
    k200, k201, k202, k203, k204, k205, k206, k207, k208, k209, k210, k211,             k213, k215, \
    k300,       k302, k303, k304, k305, k306, k307, k308, k309, k310, k311,       k312, k313, k315, \
    k400, k401, k402,                   k406,                   k409, k410, k411, k412, k413, k415  \
 ) { \
    { k000,  k001,  k002,  k003,  k004,  k005,  k006,  k007,  k008,  k009,  k010,  k011,  k012,  k013,  k014,  k015 }, \
    { k100,  k101,  k102,  k103,  k104,  k105,  k106,  k107,  k108,  k109,  k110,  k111,  k112,  k113,  KC_NO, k115 }, \
    { k200,  k201,  k202,  k203,  k204,  k205,  k206,  k207,  k208,  k209,  k210,  k211,  KC_NO, k213,  KC_NO, k215 }, \
    { k300,  KC_NO, k302,  k303,  k304,  k305,  k306,  k307,  k308,  k309,  k310,  k311,  k312,  k313,  KC_NO, k315 }, \
    { k400,  k401,  k402,  KC_NO, KC_NO, KC_NO, k406,  KC_NO, KC_NO, k409,  k410,  k411,  k412,  k413,  KC_NO, k415 }  \
 }
 #define LAYOUT_65_ansi( \
    k000, k001, k002, k003, k004, k005, k006, k007, k008, k009, k010, k011, k012,       k014, k015, \
    k100, k101, k102, k103, k104, k105, k106, k107, k108, k109, k110, k111, k112,       k113, k115, \
    k200, k201, k202, k203, k204, k205, k206, k207, k208, k209, k210, k211,             k213, k215, \
    k300,       k302, k303, k304, k305, k306, k307, k308, k309, k310, k311,       k312, k313, k315, \
    k400, k401, k402,                   k406,                   k409, k410, k411, k412, k413, k415  \
 ) { \
    { k000,  k001,  k002,  k003,  k004,  k005,  k006,  k007,  k008,  k009,  k010,  k011,  k012,  KC_NO, k014,  k015 }, \
    { k100,  k101,  k102,  k103,  k104,  k105,  k106,  k107,  k108,  k109,  k110,  k111,  k112,  k113,  KC_NO, k115 }, \
    { k200,  k201,  k202,  k203,  k204,  k205,  k206,  k207,  k208,  k209,  k210,  k211,  KC_NO, k213,  KC_NO, k215 }, \
    { k300,  KC_NO, k302,  k303,  k304,  k305,  k306,  k307,  k308,  k309,  k310,  k311,  k312,  k313,  KC_NO, k315 }, \
    { k400,  k401,  k402,  KC_NO, KC_NO, KC_NO, k406,  KC_NO, KC_NO, k409,  k410,  k411,  k412,  k413,  KC_NO, k415 }  \
 }
 #define LAYOUT_65_ansi_split_bs_2_right_mods( \
    k000, k001, k002, k003, k004, k005, k006, k007, k008, k009, k010, k011, k012, k013, k014, k015, \
    k100, k101, k102, k103, k104, k105, k106, k107, k108, k109, k110, k111, k112,       k113, k115, \
    k200, k201, k202, k203, k204, k205, k206, k207, k208, k209, k210, k211,             k213, k215, \
    k300,       k302, k303, k304, k305, k306, k307, k308, k309, k310, k311,       k312, k313, k315, \
    k400, k401, k402,                   k406,                   k409,       k411, k412, k413, k415  \
 ) { \
    { k000,  k001,  k002,  k003,  k004,  k005,  k006,  k007,  k008,  k009,  k010,  k011,  k012,  k013,  k014,  k015 }, \
    { k100,  k101,  k102,  k103,  k104,  k105,  k106,  k107,  k108,  k109,  k110,  k111,  k112,  k113,  KC_NO, k115 }, \
    { k200,  k201,  k202,  k203,  k204,  k205,  k206,  k207,  k208,  k209,  k210,  k211,  KC_NO, k213,  KC_NO, k215 }, \
    { k300,  KC_NO, k302,  k303,  k304,  k305,  k306,  k307,  k308,  k309,  k310,  k311,  k312,  k313,  KC_NO, k315 }, \
    { k400,  k401,  k402,  KC_NO, KC_NO, KC_NO, k406,  KC_NO, KC_NO, k409,  KC_NO, k411,  k412,  k413,  KC_NO, k415 }  \
 }
 #define LAYOUT_65_ansi_2_right_mods( \
    k000, k001, k002, k003, k004, k005, k006, k007, k008, k009, k010, k011, k012,       k014, k015, \
    k100, k101, k102, k103, k104, k105, k106, k107, k108, k109, k110, k111, k112,       k113, k115, \
    k200, k201, k202, k203, k204, k205, k206, k207, k208, k209, k210, k211,             k213, k215, \
    k300,       k302, k303, k304, k305, k306, k307, k308, k309, k310, k311,       k312, k313, k315, \
    k400, k401, k402,                   k406,                   k409,       k411, k412, k413, k415  \
 ) { \
    { k000,  k001,  k002,  k003,  k004,  k005,  k006,  k007,  k008,  k009,  k010,  k011,  k012,  KC_NO, k014,  k015 }, \
    { k100,  k101,  k102,  k103,  k104,  k105,  k106,  k107,  k108,  k109,  k110,  k111,  k112,  k113,  KC_NO, k115 }, \
    { k200,  k201,  k202,  k203,  k204,  k205,  k206,  k207,  k208,  k209,  k210,  k211,  KC_NO, k213,  KC_NO, k215 }, \
    { k300,  KC_NO, k302,  k303,  k304,  k305,  k306,  k307,  k308,  k309,  k310,  k311,  k312,  k313,  KC_NO, k315 }, \
    { k400,  k401,  k402,  KC_NO, KC_NO, KC_NO, k406,  KC_NO, KC_NO, k409,  KC_NO, k411,  k412,  k413,  KC_NO, k415 }  \
 }
@@ -0,0 +1,109 @@
 /*
 Copyright 2020 Koichi Katano
 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
 the Free Software Foundation, either version 2 of the License, or
 (at your option) any later version.
 This program is distributed in the hope that it will be useful,
 but WITHOUT ANY WARRANTY; without even the implied warranty of
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 GNU General Public License for more details.
 You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "config_common.h"
 /* USB Device descriptor parameter */
 #define VENDOR_ID    0x3A0E
 #define PRODUCT_ID   0x4C82
 #define DEVICE_VER   0x0001
 #define MANUFACTURER kkatano
 #define PRODUCT      Bakeneko 65
 /* key matrix size */
 #define MATRIX_ROWS 5
 #define MATRIX_COLS 16
 /*
 * Keyboard Matrix Assignments
 *
 * Change this to how you wired your keyboard
 * COLS: AVR pins used for columns, left to right
 * ROWS: AVR pins used for rows, top to bottom
 * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
 *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
 *
 */
 #define MATRIX_ROW_PINS { E6, B7, F7, F4, F5 }
 #define MATRIX_COL_PINS { F6, B0, F1, C7, C6, B6, B5, B4, D7, D6, D4, D5, D3, D2, D1, D0 }
 #define UNUSED_PINS
 /* COL2ROW, ROW2COL */
 #define DIODE_DIRECTION COL2ROW
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 /* define if matrix has ghost (lacks anti-ghosting diodes) */
 //#define MATRIX_HAS_GHOST
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 /* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
 * This is useful for the Windows task manager shortcut (ctrl+shift+esc).
 */
 //#define GRAVE_ESC_CTRL_OVERRIDE
 /*
 * Force NKRO
 *
 * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
 * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
 * makefile for this to work.)
 *
 * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
 * until the next keyboard reset.
 *
 * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
 * fully operational during normal computer usage.
 *
 * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
 * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
 * bootmagic, NKRO mode will always be enabled until it is toggled again during a
 * power-up.
 *
 */
 //#define FORCE_NKRO
 /*
 * Feature disable options
 *  These options are also useful to firmware size reduction.
 */
 /* disable debug print */
 //#define NO_DEBUG
 /* disable print */
 //#define NO_PRINT
 /* disable action features */
 //#define NO_ACTION_LAYER
 //#define NO_ACTION_TAPPING
 //#define NO_ACTION_ONESHOT
 /* disable these deprecated features by default */
 #define NO_ACTION_MACRO
 #define NO_ACTION_FUNCTION
 /* Bootmagic Lite key configuration */
 //#define BOOTMAGIC_LITE_ROW 0
 //#define BOOTMAGIC_LITE_COLUMN 0
@@ -0,0 +1,313 @@
 {
    "keyboard_name": "Bakeneko 65",
    "url": "https://github.com/kkatano/bakeneko-65-pcb",
    "maintainer": "kkatano",
    "width": 16,
    "height": 5,
    "layouts": {
        "LAYOUT_65_ansi_split_bs": {
            "layout": [
                { "x":0, "y":0 },
                { "x":1, "y":0 },
                { "x":2, "y":0 },
                { "x":3, "y":0 },
                { "x":4, "y":0 },
                { "x":5, "y":0 },
                { "x":6, "y":0 },
                { "x":7, "y":0 },
                { "x":8, "y":0 },
                { "x":9, "y":0 },
                { "x":10, "y":0 },
                { "x":11, "y":0 },
                { "x":12, "y":0 },
                { "x":13, "y":0 },
                { "x":14, "y":0 },
                { "x":15, "y":0 },
                { "x":0, "y":1, "w":1.5 },
                { "x":1.5, "y":1 },
                { "x":2.5, "y":1 },
                { "x":3.5, "y":1 },
                { "x":4.5, "y":1 },
                { "x":5.5, "y":1 },
                { "x":6.5, "y":1 },
                { "x":7.5, "y":1 },
                { "x":8.5, "y":1 },
                { "x":9.5, "y":1 },
                { "x":10.5, "y":1 },
                { "x":11.5, "y":1 },
                { "x":12.5, "y":1 },
                { "x":13.5, "y":1, "w":1.5 },
                { "x":15, "y":1 },
                { "x":0, "y":2, "w":1.75 },
                { "x":1.75, "y":2 },
                { "x":2.75, "y":2 },
                { "x":3.75, "y":2 },
                { "x":4.75, "y":2 },
                { "x":5.75, "y":2 },
                { "x":6.75, "y":2 },
                { "x":7.75, "y":2 },
                { "x":8.75, "y":2 },
                { "x":9.75, "y":2 },
                { "x":10.75, "y":2 },
                { "x":11.75, "y":2 },
                { "x":12.75, "y":2, "w":2.25 },
                { "x":15, "y":2 },
                { "x":0, "y":3, "w":2.25 },
                { "x":2.25, "y":3 },
                { "x":3.25, "y":3 },
                { "x":4.25, "y":3 },
                { "x":5.25, "y":3 },
                { "x":6.25, "y":3 },
                { "x":7.25, "y":3 },
                { "x":8.25, "y":3 },
                { "x":9.25, "y":3 },
                { "x":10.25, "y":3 },
                { "x":11.25, "y":3 },
                { "x":12.25, "y":3, "w":1.75 },
                { "x":14, "y":3 },
                { "x":15, "y":3 },
                { "x":0, "y":4, "w":1.25 },
                { "x":1.25, "y":4, "w":1.25 },
                { "x":2.5, "y":4, "w":1.25 },
                { "x":3.75, "y":4, "w":6.25 },
                { "x":10, "y":4 },
                { "x":11, "y":4 },
                { "x":12, "y":4 },
                { "x":13, "y":4 },
                { "x":14, "y":4 },
                { "x":15, "y":4 }
            ]
        },
        "LAYOUT_65_ansi": {
            "layout": [
                { "x":0, "y":0 },
                { "x":1, "y":0 },
                { "x":2, "y":0 },
                { "x":3, "y":0 },
                { "x":4, "y":0 },
                { "x":5, "y":0 },
                { "x":6, "y":0 },
                { "x":7, "y":0 },
                { "x":8, "y":0 },
                { "x":9, "y":0 },
                { "x":10, "y":0 },
                { "x":11, "y":0 },
                { "x":12, "y":0 },
                { "x":13, "y":0, "w": 2 },
                { "x":15, "y":0 },
                { "x":0, "y":1, "w":1.5 },
                { "x":1.5, "y":1 },
                { "x":2.5, "y":1 },
                { "x":3.5, "y":1 },
                { "x":4.5, "y":1 },
                { "x":5.5, "y":1 },
                { "x":6.5, "y":1 },
                { "x":7.5, "y":1 },
                { "x":8.5, "y":1 },
                { "x":9.5, "y":1 },
                { "x":10.5, "y":1 },
                { "x":11.5, "y":1 },
                { "x":12.5, "y":1 },
                { "x":13.5, "y":1, "w":1.5 },
                { "x":15, "y":1 },
                { "x":0, "y":2, "w":1.75 },
                { "x":1.75, "y":2 },
                { "x":2.75, "y":2 },
                { "x":3.75, "y":2 },
                { "x":4.75, "y":2 },
                { "x":5.75, "y":2 },
                { "x":6.75, "y":2 },
                { "x":7.75, "y":2 },
                { "x":8.75, "y":2 },
                { "x":9.75, "y":2 },
                { "x":10.75, "y":2 },
                { "x":11.75, "y":2 },
                { "x":12.75, "y":2, "w":2.25 },
                { "x":15, "y":2 },
                { "x":0, "y":3, "w":2.25 },
                { "x":2.25, "y":3 },
                { "x":3.25, "y":3 },
                { "x":4.25, "y":3 },
                { "x":5.25, "y":3 },
                { "x":6.25, "y":3 },
                { "x":7.25, "y":3 },
                { "x":8.25, "y":3 },
                { "x":9.25, "y":3 },
                { "x":10.25, "y":3 },
                { "x":11.25, "y":3 },
                { "x":12.25, "y":3, "w":1.75 },
                { "x":14, "y":3 },
                { "x":15, "y":3 },
                { "x":0, "y":4, "w":1.25 },
                { "x":1.25, "y":4, "w":1.25 },
                { "x":2.5, "y":4, "w":1.25 },
                { "x":3.75, "y":4, "w":6.25 },
                { "x":10, "y":4 },
                { "x":11, "y":4 },
                { "x":12, "y":4 },
                { "x":13, "y":4 },
                { "x":14, "y":4 },
                { "x":15, "y":4 }
            ]
        },
        "LAYOUT_65_ansi_split_bs_2_right_mods": {
            "layout": [
                { "x":0, "y":0 },
                { "x":1, "y":0 },
                { "x":2, "y":0 },
                { "x":3, "y":0 },
                { "x":4, "y":0 },
                { "x":5, "y":0 },
                { "x":6, "y":0 },
                { "x":7, "y":0 },
                { "x":8, "y":0 },
                { "x":9, "y":0 },
                { "x":10, "y":0 },
                { "x":11, "y":0 },
                { "x":12, "y":0 },
                { "x":13, "y":0 },
                { "x":14, "y":0 },
                { "x":15, "y":0 },
                { "x":0, "y":1, "w":1.5 },
                { "x":1.5, "y":1 },
                { "x":2.5, "y":1 },
                { "x":3.5, "y":1 },
                { "x":4.5, "y":1 },
                { "x":5.5, "y":1 },
                { "x":6.5, "y":1 },
                { "x":7.5, "y":1 },
                { "x":8.5, "y":1 },
                { "x":9.5, "y":1 },
                { "x":10.5, "y":1 },
                { "x":11.5, "y":1 },
                { "x":12.5, "y":1 },
                { "x":13.5, "y":1, "w":1.5 },
                { "x":15, "y":1 },
                { "x":0, "y":2, "w":1.75 },
                { "x":1.75, "y":2 },
                { "x":2.75, "y":2 },
                { "x":3.75, "y":2 },
                { "x":4.75, "y":2 },
                { "x":5.75, "y":2 },
                { "x":6.75, "y":2 },
                { "x":7.75, "y":2 },
                { "x":8.75, "y":2 },
                { "x":9.75, "y":2 },
                { "x":10.75, "y":2 },
                { "x":11.75, "y":2 },
                { "x":12.75, "y":2, "w":2.25 },
                { "x":15, "y":2 },
                { "x":0, "y":3, "w":2.25 },
                { "x":2.25, "y":3 },
                { "x":3.25, "y":3 },
                { "x":4.25, "y":3 },
                { "x":5.25, "y":3 },
                { "x":6.25, "y":3 },
                { "x":7.25, "y":3 },
                { "x":8.25, "y":3 },
                { "x":9.25, "y":3 },
                { "x":10.25, "y":3 },
                { "x":11.25, "y":3 },
                { "x":12.25, "y":3, "w":1.75 },
                { "x":14, "y":3 },
                { "x":15, "y":3 },
                { "x":0, "y":4, "w":1.25 },
                { "x":1.25, "y":4, "w":1.25 },
                { "x":2.5, "y":4, "w":1.25 },
                { "x":3.75, "y":4, "w":6.25 },
                { "x":10, "y":4, "w":1.5 },
                { "x":11.5, "y":4, "w":1.5 },
                { "x":13, "y":4 },
                { "x":14, "y":4 },
                { "x":15, "y":4 }
            ]
        },
        "LAYOUT_65_ansi_2_right_mods": {
            "layout": [
                { "x":0, "y":0 },
                { "x":1, "y":0 },
                { "x":2, "y":0 },
                { "x":3, "y":0 },
                { "x":4, "y":0 },
                { "x":5, "y":0 },
                { "x":6, "y":0 },
                { "x":7, "y":0 },
                { "x":8, "y":0 },
                { "x":9, "y":0 },
                { "x":10, "y":0 },
                { "x":11, "y":0 },
                { "x":12, "y":0 },
                { "x":13, "y":0, "w": 2 },
                { "x":15, "y":0 },
                { "x":0, "y":1, "w":1.5 },
                { "x":1.5, "y":1 },
                { "x":2.5, "y":1 },
                { "x":3.5, "y":1 },
                { "x":4.5, "y":1 },
                { "x":5.5, "y":1 },
                { "x":6.5, "y":1 },
                { "x":7.5, "y":1 },
                { "x":8.5, "y":1 },
                { "x":9.5, "y":1 },
                { "x":10.5, "y":1 },
                { "x":11.5, "y":1 },
                { "x":12.5, "y":1 },
                { "x":13.5, "y":1, "w":1.5 },
                { "x":15, "y":1 },
                { "x":0, "y":2, "w":1.75 },
                { "x":1.75, "y":2 },
                { "x":2.75, "y":2 },
                { "x":3.75, "y":2 },
                { "x":4.75, "y":2 },
                { "x":5.75, "y":2 },
                { "x":6.75, "y":2 },
                { "x":7.75, "y":2 },
                { "x":8.75, "y":2 },
                { "x":9.75, "y":2 },
                { "x":10.75, "y":2 },
                { "x":11.75, "y":2 },
                { "x":12.75, "y":2, "w":2.25 },
                { "x":15, "y":2 },
                { "x":0, "y":3, "w":2.25 },
                { "x":2.25, "y":3 },
                { "x":3.25, "y":3 },
                { "x":4.25, "y":3 },
                { "x":5.25, "y":3 },
                { "x":6.25, "y":3 },
                { "x":7.25, "y":3 },
                { "x":8.25, "y":3 },
                { "x":9.25, "y":3 },
                { "x":10.25, "y":3 },
                { "x":11.25, "y":3 },
                { "x":12.25, "y":3, "w":1.75 },
                { "x":14, "y":3 },
                { "x":15, "y":3 },
                { "x":0, "y":4, "w":1.25 },
                { "x":1.25, "y":4, "w":1.25 },
                { "x":2.5, "y":4, "w":1.25 },
                { "x":3.75, "y":4, "w":6.25 },
                { "x":10, "y":4, "w":1.5 },
                { "x":11.5, "y":4, "w":1.5 },
                { "x":13, "y":4 },
                { "x":14, "y":4 },
                { "x":15, "y":4 }
            ]
        }
    }
 }
@@ -0,0 +1,38 @@
 /* Copyright 2020 kkatano
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include QMK_KEYBOARD_H
 enum layer_names {
    _BASE,
    _FN
 };
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    [_BASE] = LAYOUT_65_ansi_split_bs(
        KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_GRV,  KC_BSPC, KC_HOME, 
        KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC,          KC_BSLS, KC_END,  
        KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,                   KC_ENT,  KC_PGUP, 
        KC_LSFT,          KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT, KC_UP,   KC_PGDN, 
        KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, MO(_FN), KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT
    ),
    [_FN] = LAYOUT_65_ansi_split_bs(
        RESET,   KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  _______, _______, _______,
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______,
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,                   _______, _______,
        _______,          _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______, _______,
        _______, _______, _______,                            _______,                            _______, _______, _______, _______, _______, _______
    )
 };
@@ -0,0 +1 @@
 # The default keymap for Bakeneko 65
@@ -0,0 +1,54 @@
 /* Copyright 2020 kkatano
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include QMK_KEYBOARD_H
 enum layer_names {
    _L0,
    _L1,
    _L2,
    _L3
 };
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    [_L0] = LAYOUT_65_ansi_split_bs(
        KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_GRV,  KC_BSPC, KC_HOME, 
        KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC,          KC_BSLS, KC_END,  
        KC_CAPS, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,                   KC_ENT,  KC_PGUP, 
        KC_LSFT,          KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH,          KC_RSFT, KC_UP,   KC_PGDN, 
        KC_LCTL, KC_LGUI, KC_LALT,                            KC_SPC,                             KC_RALT, MO(_L1), KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT
    ),
    [_L1] = LAYOUT_65_ansi_split_bs(
        RESET,   KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  _______, _______, _______,
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______,
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,                   _______, _______,
        _______,          _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______, _______,
        _______, _______, _______,                            _______,                            _______, _______, _______, _______, _______, _______
    ),
    [_L2] = LAYOUT_65_ansi_split_bs(
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______,
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,                   _______, _______,
        _______,          _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______, _______,
        _______, _______, _______,                            _______,                            _______, _______, _______, _______, _______, _______
    ),
    [_L3] = LAYOUT_65_ansi_split_bs(
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______,
        _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,                   _______, _______,
        _______,          _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,          _______, _______, _______,
        _______, _______, _______,                            _______,                            _______, _______, _______, _______, _______, _______
    )
 };
@@ -0,0 +1 @@
 VIA_ENABLE = yes
@@ -0,0 +1,17 @@
 # Bakeneko 65
 An open source O-ring gasket mount keyboard
 * Keyboard Maintainer: [kkatano](https://github.com/kkatano)
 * Hardware Supported: Bakeneko 65
 * Hardware Availability: [Open source on GitHub](https://github.com/kkatano/bakeneko-65-pcb)
 Make example for this keyboard (after setting up your build environment):
    make bakeneko65:default
 Flashing example for this keyboard:
    make bakeneko65:default:flash
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@@ -0,0 +1,24 @@
 # MCU name
 MCU = atmega32u4
 # Bootloader selection
 BOOTLOADER = atmel-dfu
 # Build Options
 #   change yes to no to disable
 #
 BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration
 MOUSEKEY_ENABLE = yes       # Mouse keys
 EXTRAKEY_ENABLE = yes       # Audio control and System control
 CONSOLE_ENABLE = no         # Console for debug
 COMMAND_ENABLE = no         # Commands for debug and configuration
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
 NKRO_ENABLE = no            # USB Nkey Rollover
 BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
 RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
 BLUETOOTH_ENABLE = no       # Enable Bluetooth
 AUDIO_ENABLE = no           # Audio output
 LAYOUTS = 65_ansi
@@ -0,0 +1,30 @@
 # BMEK
 ![BMEK](https://i.imgur.com/p1KFi6ql.jpg)
 BMEK combines the best of HHKB & Alice-likes. All PCB and case design files are open source.
 * Keyboard Maintainer: [Bemeier](https://github.com/Bemeier)
 * Hardware Supported: BMEK PCB rev1, rev2, rev3
 * Hardware Availability: Case & PCB files: [github.com/bemeier/bmek](https://github.com/bemeier/bmek)
 Make example for this keyboard, for an hhkb-like layout and keymap (after setting up your build environment):
    make bemeier/bmek/rev3:default
 Make the VIA compatible firmware:
    make bemeier/bmek/rev3:via
 The ```rev3```, denotes the version of the PCB.
 Check on the PCB to find out which version you have, and set it to rev1, rev2 or rev3 accordingly (the BMEK group buy PCBs are all rev3).
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
 # Layouts
 Starting with rev3 (the version of the PCB to be shipped in the GB), the following layout options are supported:
 ![layouts](https://i.imgur.com/XuFxwthl.png)
 Note that the keymap shown above may not accurately reflect the default keymap of the firmware (see the keymaps folder).
@@ -0,0 +1,23 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include "bmek.h"
 __attribute__((weak))
 void shutdown_user() {
 #ifdef RGBLIGHT_ENABLE
    rgblight_setrgb(255, 0, 0);
 #endif
 }
@@ -0,0 +1,58 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "quantum.h"
 #if defined(KEYBOARD_bemeier_bmek_rev1)
 #    include "rev1.h"
 #elif defined(KEYBOARD_bemeier_bmek_rev2)
 #    include "rev2.h"
 #elif defined(KEYBOARD_bemeier_bmek_rev3)
 #    include "rev3.h"
 #endif
 #define XXX KC_NO  // makes the switch matrix easier to read
 // This layout is supported by all revisions
 #define LAYOUT_hhkb(\
       K00, K01, K02, K03, K04, K05, K06, K07,     K08, K09, K0A, K0B, K0C, K0D, K0E, K1E,\
      K10,  K11,  K12, K13, K14, K15, K16,        K17, K18, K19, K1A, K1B, K1C, K1D,   K2E,\
     K20,   K21,   K22, K23, K24, K25, K26,        K27, K28, K29, K2A, K2B,     K2C,    K2D,\
    K30,      K31,  K32,   K33, K34, K35, K36,   K37, K38, K39, K3A,  K3B, K3C,  K3D,    K3E,\
                    K42,   K43,      K45,             K48,      K4A,  K4B                     \
   ) { \
    { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E }, \
    { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E }, \
    { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, K2E }, \
    { K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, K3E }, \
    { XXX, XXX, K42, K43, XXX, K45, XXX, XXX, K48, XXX, K4A, K4B, XXX, XXX, XXX }  \
 }
 // Layout exposing all keys (adding the ISO-style split left shift, which is supported starting rev3)
 #define LAYOUT_all(\
       K00, K01, K02, K03, K04, K05, K06, K07,     K08, K09, K0A, K0B, K0C, K0D, K0E, K1E,\
      K10,  K11,  K12, K13, K14, K15, K16,        K17, K18, K19, K1A, K1B, K1C, K1D,   K2E,\
     K20,   K21,   K22, K23, K24, K25, K26,        K27, K28, K29, K2A, K2B,     K2C,    K2D,\
    K30,  K31, K41, K32,   K33, K34, K35, K36,   K37, K38, K39, K3A,  K3B, K3C,  K3D,    K3E,\
                    K42,   K43,      K45,             K48,      K4A,  K4B                     \
   ) { \
    { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K0E }, \
    { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, K1E }, \
    { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, K2E }, \
    { K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, K3E }, \
    { XXX, K41, K42, K43, XXX, K45, XXX, XXX, K48, XXX, K4A, K4B, XXX, XXX, XXX }  \
 }
@@ -0,0 +1,47 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "config_common.h"
 /* USB Device descriptor parameter */
 #define VENDOR_ID 0x626D // BeMeier
 #define PRODUCT_ID 0x656B // ErgonomicKeyboard
 #define MANUFACTURER Bemeier
 #define PRODUCT BMEK
 #define DYNAMIC_KEYMAP_LAYER_COUNT 5
 #define VIA_EEPROM_CUSTOM_CONFIG_SIZE 20 
 /* Keyboard Matrix size */
 #define MATRIX_ROWS 5
 #define MATRIX_COLS 15
 #define DIODE_DIRECTION COL2ROW
 #define RGBLIGHT_EFFECT_BREATHING
 #define RGBLIGHT_EFFECT_RAINBOW_MOOD
 #define RGBLIGHT_MODE_STATIC_GRADIENT
 #define RGBLED_NUM 6
 #define RGBLIGHT_HUE_STEP 8
 #define RGBLIGHT_SAT_STEP 8
 #define RGBLIGHT_VAL_STEP 8
 #define RGBLIGHT_LIMIT_VAL 255
 #define DEBOUNCE 5
 //#define RETRO_TAPPING
 #define TAPPING_TERM 175
@@ -0,0 +1,25 @@
 {
    "keyboard_name": "bmek", 
    "url": "https://github.com/Bemeier/bmek", 
    "maintainer": "Bemeier", 
    "width": 18, 
    "height": 5,
    "layouts": {
        "LAYOUT_all": {
            "layout": [
                {"label":"Home", "x":0, "y":0}, {"label":"Esc", "x":1.5, "y":0}, {"label":"!", "x":2.5, "y":0}, {"label":"@", "x":3.5, "y":0}, {"label":"#", "x":4.5, "y":0}, {"label":"$", "x":5.5, "y":0}, {"label":"%", "x":6.5, "y":0}, {"label":"^", "x":7.5, "y":0}, {"label":"&", "x":10, "y":0}, {"label":"*", "x":11, "y":0}, {"label":"(", "x":12, "y":0}, {"label":")", "x":13, "y":0}, {"label":"_", "x":14, "y":0}, {"label":"+", "x":15, "y":0}, {"label":"|", "x":16, "y":0}, {"label":"~", "x":17, "y":0},
                {"label":"PgUp", "x":0, "y":1}, {"label":"Tab", "x":1.5, "y":1, "w":1.5}, {"label":"Q", "x":3, "y":1}, {"label":"W", "x":4, "y":1}, {"label":"E", "x":5, "y":1}, {"label":"R", "x":6, "y":1}, {"label":"T", "x":7, "y":1}, {"label":"Y", "x":9.5, "y":1}, {"label":"U", "x":10.5, "y":1}, {"label":"I", "x":11.5, "y":1}, {"label":"O", "x":12.5, "y":1}, {"label":"P", "x":13.5, "y":1}, {"label":"{", "x":14.5, "y":1}, {"label":"}", "x":15.5, "y":1}, {"label":"Backspace", "x":16.5, "y":1, "w":1.5},
                {"label":"PgDn", "x":0, "y":2}, {"label":"Ctrl", "x":1.5, "y":2, "w":1.75}, {"label":"A", "x":3.25, "y":2}, {"label":"S", "x":4.25, "y":2}, {"label":"D", "x":5.25, "y":2}, {"label":"F", "x":6.25, "y":2}, {"label":"G", "x":7.25, "y":2}, {"label":"H", "x":9.75, "y":2}, {"label":"J", "x":10.75, "y":2}, {"label":"K", "x":11.75, "y":2}, {"label":"L", "x":12.75, "y":2}, {"label":":", "x":13.75, "y":2}, {"label":"\"", "x":14.75, "y":2}, {"label":"Enter", "x":15.75, "y":2, "w":2.25},
                {"label":"End", "x":0, "y":3}, {"label":"Shift", "x":1.5, "y":3, "w":1.25}, {"label":"~", "x":2.75, "y":3}, {"label":"Z", "x":3.75, "y":3}, {"label":"X", "x":4.75, "y":3}, {"label":"C", "x":5.75, "y":3}, {"label":"V", "x":6.75, "y":3}, {"label":"B", "x":7.75, "y":3}, {"label":"B", "x":9.25, "y":3}, {"label":"N", "x":10.25, "y":3}, {"label":"M", "x":11.25, "y":3}, {"label":"<", "x":12.25, "y":3}, {"label":">", "x":13.25, "y":3}, {"label":"?", "x":14.25, "y":3}, {"label":"Shift", "x":15.25, "y":3, "w":1.75}, {"label":"Fn", "x":17, "y":3}, {"label":"Win", "x":3.75, "y":4}, {"label":"Alt", "x":4.75, "y":4, "w":1.25}, {"x":6, "y":4, "w":2.75}, {"x":9.25, "y":4, "w":2.75}, {"label":"Alt", "x":12, "y":4, "w":1.25}, {"label":"Win", "x":13.25, "y":4}
            ]
        },
        "LAYOUT_hhkb": {
            "layout": [
                {"label":"Home", "x":0, "y":0}, {"label":"Esc", "x":1.5, "y":0}, {"label":"!", "x":2.5, "y":0}, {"label":"@", "x":3.5, "y":0}, {"label":"#", "x":4.5, "y":0}, {"label":"$", "x":5.5, "y":0}, {"label":"%", "x":6.5, "y":0}, {"label":"^", "x":7.5, "y":0}, {"label":"&", "x":10, "y":0}, {"label":"*", "x":11, "y":0}, {"label":"(", "x":12, "y":0}, {"label":")", "x":13, "y":0}, {"label":"_", "x":14, "y":0}, {"label":"+", "x":15, "y":0}, {"label":"|", "x":16, "y":0}, {"label":"~", "x":17, "y":0},
                {"label":"PgUp", "x":0, "y":1}, {"label":"Tab", "x":1.5, "y":1, "w":1.5}, {"label":"Q", "x":3, "y":1}, {"label":"W", "x":4, "y":1}, {"label":"E", "x":5, "y":1}, {"label":"R", "x":6, "y":1}, {"label":"T", "x":7, "y":1}, {"label":"Y", "x":9.5, "y":1}, {"label":"U", "x":10.5, "y":1}, {"label":"I", "x":11.5, "y":1}, {"label":"O", "x":12.5, "y":1}, {"label":"P", "x":13.5, "y":1}, {"label":"{", "x":14.5, "y":1}, {"label":"}", "x":15.5, "y":1}, {"label":"Backspace", "x":16.5, "y":1, "w":1.5},
                {"label":"PgDn", "x":0, "y":2}, {"label":"Ctrl", "x":1.5, "y":2, "w":1.75}, {"label":"A", "x":3.25, "y":2}, {"label":"S", "x":4.25, "y":2}, {"label":"D", "x":5.25, "y":2}, {"label":"F", "x":6.25, "y":2}, {"label":"G", "x":7.25, "y":2}, {"label":"H", "x":9.75, "y":2}, {"label":"J", "x":10.75, "y":2}, {"label":"K", "x":11.75, "y":2}, {"label":"L", "x":12.75, "y":2}, {"label":":", "x":13.75, "y":2}, {"label":"\"", "x":14.75, "y":2}, {"label":"Enter", "x":15.75, "y":2, "w":2.25},
                {"label":"End", "x":0, "y":3}, {"label":"Shift", "x":1.5, "y":3, "w":2.25}, {"label":"Z", "x":3.75, "y":3}, {"label":"X", "x":4.75, "y":3}, {"label":"C", "x":5.75, "y":3}, {"label":"V", "x":6.75, "y":3}, {"label":"B", "x":7.75, "y":3}, {"label":"B", "x":9.25, "y":3}, {"label":"N", "x":10.25, "y":3}, {"label":"M", "x":11.25, "y":3}, {"label":"<", "x":12.25, "y":3}, {"label":">", "x":13.25, "y":3}, {"label":"?", "x":14.25, "y":3}, {"label":"Shift", "x":15.25, "y":3, "w":1.75}, {"label":"Fn", "x":17, "y":3}, {"label":"Win", "x":3.75, "y":4}, {"label":"Alt", "x":4.75, "y":4, "w":1.25}, {"x":6, "y":4, "w":2.75}, {"x":9.25, "y":4, "w":2.75}, {"label":"Alt", "x":12, "y":4, "w":1.25}, {"label":"Win", "x":13.25, "y":4}
            ]
        }
    }
 }
@@ -0,0 +1,4 @@
 # Default BMEK Keymap
 This is the default keymap for the BMEK, besides the left macro columns and the split spacebars.
 It's uses the HHKB-like layout options (no split left shift, split backspace and split right shift).
 Please checkout the diagrams in ```keymap.c``` for an overview of the keymap.
@@ -0,0 +1,76 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include QMK_KEYBOARD_H
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   [0] = LAYOUT_hhkb(
 /* Default layer
 ┌─────┐ ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┐    ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┬─────┐
 │ F13 │ │ ESC │  1  │  2  │  3  │  4  │  5  │  6  │    │  7  │  8  │  9  │  0  │  -  │  =  │  \  │  `  │
 ├─────┤ ├─────┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┘  ┌─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴─────┤
 │ F14 │ │  TAB  │  Q  │  W  │  E  │  R  │  T  │      │  Y  │  U  │  I  │  O  │  P  │  [  │  ]  │  BSPC │
 ├─────┤ ├───────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     └─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴───────┤
 │ F15 │ │  CTRL  │  A  │  S  │  D  │  F  │  G  │       │  H  │  J  │  K  │  L  │  ;  │  '  │   ENTER   │
 ├─────┤ ├────────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     ┌┴────┬┴────┬┴────┬┴────┬┴────┬┴────┬┴──────┬────┤
 │ F16 │ │ SHFT    │  Z  │  X  │  C  │  V  │  B  │     │  B  │  N  │  M  │  ,  │  .  │  /  │  SHFT │ Fn │
 └─────┘ └─────────┼─────┼─────┴┬────┴─────┴─────┤     ├─────┴─────┴────┬┴─────┼─────┼─────┴───────┴────┘
                  │ GUI │ ALT  │     SPACE      │     │   SPACE/Fn_1   │  ALT │ CTL │
                  └─────┴──────┴────────────────┘     └────────────────┴──────┴─────┘
 */
  KC_F13,  KC_ESC,    KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,     KC_7,    KC_8,    KC_9,    KC_0, KC_MINS,  KC_EQL, KC_BSLS,  KC_GRV,
  KC_F14,  KC_TAB,      KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,           KC_Y,    KC_U,    KC_I,    KC_O,    KC_P, KC_LBRC, KC_RBRC,  KC_BSPC,
  KC_F15, KC_LCTL,       KC_A,    KC_S,    KC_D,    KC_F,    KC_G,             KC_H,    KC_J,    KC_K,    KC_L, KC_SCLN, KC_QUOT,         KC_ENT,
  KC_F16, KC_LSFT,         KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,         KC_B,   KC_N,    KC_M, KC_COMM,  KC_DOT, KC_SLSH,   KC_RSFT,  MO(1),
                     KC_LGUI, KC_LALT,                KC_SPC,           LT(1, KC_SPC),          KC_RALT, KC_RCTL
 ), [1] = LAYOUT_hhkb(
 /* Function Layer 1: Nav
 ┌─────┐ ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┐    ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┬─────┐
 │ RST │ │ PWR │ F1  │ F2  │ F3  │ F4  │ F5  │ F6  │    │ F7  │ F8  │ F9  │ F10 │ F11 │ F12 │ INS │ DEL │
 ├─────┤ ├─────┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┘  ┌─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴─────┤
 │     │ │ CAPS  │     │     │     │     │     │      │     │     │PSCR │SLCK │PAUS │  ^  │     │       │
 ├─────┤ ├───────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     └─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴───────┤
 │     │ │        │ o)  │ o)} │  Ø  │EJCT │     │       │  *  │  /  │HOME │PGUP │ <-  │  -> │           │
 ├─────┤ ├────────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     ┌┴────┬┴────┬┴────┬┴────┬┴────┬┴────┬┴──────┬────┤
 │     │ │         │     │     │ CFG │     │     │     │  +  │  -  │     │ END │PGDN │  v  │       │    │
 └─────┘ └─────────┼─────┼─────┴┬────┴─────┴─────┤     ├─────┴─────┴────┬┴─────┼─────┼─────┴───────┴────┘
                  │     │      │                │     │                │      │     │
                  └─────┴──────┴────────────────┘     └────────────────┴──────┴─────┘
 */
 RESET,   KC_PWR,   KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,    KC_F7,   KC_F8,   KC_F9,  KC_F10,  KC_F11,  KC_F12,  KC_INS,  KC_DEL,
 _______, KC_CAPS,   _______, _______, _______, _______, _______,        _______, _______, KC_PSCR, KC_SLCK, KC_PAUS,   KC_UP, _______,  _______,
 _______, _______,    KC_VOLD, KC_VOLU, KC_MUTE, KC_EJCT, _______,          KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT,        KC_PENT,
 _______, _______, _______, _______, TG(2), _______, _______, _______,    KC_PPLS, KC_PMNS,  KC_END, KC_PGDN, KC_DOWN,       _______,    _______,
                     _______, _______,               _______,                 _______,          _______, _______
 ), [2] = LAYOUT_hhkb(
 /* Function Layer 4: Firmware Config (TODO)
 ┌─────┐ ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┐    ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┬─────┐
 │ RST │ │     │     │     │     │     │     │     │    │     │     │     │     │     │     │     │     │
 ├─────┤ ├─────┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┘  ┌─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴─────┤
 │     │ │       │ RGB │RGB+ │RGB- │HUE+ │HUE- │      │     │     │     │     │     │     │     │       │
 ├─────┤ ├───────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     └─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴───────┤
 │     │ │        │     │SPD+ │SPD- │SAT+ │SAT- │       │     │     │     │     │     │     │           │
 ├─────┤ ├────────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     ┌┴────┬┴────┬┴────┬┴────┬┴────┬┴────┬┴──────┬────┤
 │     │ │         │     │     │ ___ │VAL+ │VAL- │     │     │     │     │     │     │     │       │    │
 └─────┘ └─────────┼─────┼─────┴┬────┴─────┴─────┤     ├─────┴─────┴────┬┴─────┼─────┼─────┴───────┴────┘
                  │     │      │                │     │                │      │     │
                  └─────┴──────┴────────────────┘     └────────────────┴──────┴─────┘
 */
 RESET,   XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,  XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,
 XXXXXXX, XXXXXXX,  RGB_TOG, RGB_MOD, RGB_RMOD, RGB_HUI, RGB_HUD,        XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,  XXXXXXX,
 XXXXXXX, XXXXXXX,    XXXXXXX, RGB_SPI, RGB_SPD, RGB_SAI, RGB_SAD,          XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,        XXXXXXX,
 XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,   TG(2), RGB_VAI, RGB_VAD,          XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,  _______,
                     XXXXXXX, XXXXXXX,               XXXXXXX,                 _______,          XXXXXXX, XXXXXXX
 ) };
@@ -0,0 +1,18 @@
 # Default VIA Keymap
 Compile the firmware with this keymap for use the BMEK with the [VIA configurator](https://caniusevia.com/).
 Layout options can be configured in VIA (see first screenshot below).
 ## 0: Base Layer
 ![Base Layer](https://i.imgur.com/tBu50SS.png)
 ## 1: Nav Layer
 ![Nav Layer](https://i.imgur.com/ZzEow3t.png)
 ## 2: NUM Block
 ![NUM Block](https://i.imgur.com/vzjZIa1.png)
 ## 4: FW Config
 ![FW Config](https://i.imgur.com/L7QynAb.png)
 ## Alternative Preconfigured Layouts
 TODO: Provide (links to) some alternative via keymaps after VIA support is landed upstream.
@@ -0,0 +1,114 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include QMK_KEYBOARD_H
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   [0] = LAYOUT_all(
 /* Default layer
 ┌─────┐ ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┐    ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┬─────┐
 │ F13 │ │ ESC │  1  │  2  │  3  │  4  │  5  │  6  │    │  7  │  8  │  9  │  0  │  -  │  =  │  \  │  `  │
 ├─────┤ ├─────┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┘  ┌─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴─────┤
 │ F14 │ │  TAB  │  Q  │  W  │  E  │  R  │  T  │      │  Y  │  U  │  I  │  O  │  P  │  [  │  ]  │  BSPC │
 ├─────┤ ├───────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     └─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴───────┤
 │ F15 │ │  CTRL  │  A  │  S  │  D  │  F  │  G  │       │  H  │  J  │  K  │  L  │  ;  │  '  │   ENTER   │
 ├─────┤ ├───────┬┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     ┌┴────┬┴────┬┴────┬┴────┬┴────┬┴────┬┴──────┬────┤
 │ F16 │ │ SHFT  │`│  Z  │  X  │  C  │  V  │  B  │     │  B  │  N  │  M  │  ,  │  .  │  /  │  SHFT │ Fn │
 └─────┘ └───────┴─┼─────┼─────┴┬────┴─────┴─────┤     ├─────┴─────┴────┬┴─────┼─────┼─────┴───────┴────┘
                  │ GUI │ ALT  │     SPACE      │     │   SPACE/Fn_1   │  ALT │ CTL │
                  └─────┴──────┴────────────────┘     └────────────────┴──────┴─────┘
 */
  KC_F13,  KC_ESC,    KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,     KC_7,    KC_8,    KC_9,    KC_0, KC_MINS,  KC_EQL, KC_BSLS,  KC_GRV,
  KC_F14,  KC_TAB,      KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,           KC_Y,    KC_U,    KC_I,    KC_O,    KC_P, KC_LBRC, KC_RBRC,  KC_BSPC,
  KC_F15, KC_LCTL,       KC_A,    KC_S,    KC_D,    KC_F,    KC_G,             KC_H,    KC_J,    KC_K,    KC_L, KC_SCLN, KC_QUOT,         KC_ENT,
  KC_F16, KC_LSFT,  KC_GRV,    KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_B,    KC_N,    KC_M, KC_COMM,  KC_DOT, KC_SLSH, KC_RSFT,    MO(1),
                     KC_LGUI, KC_LALT,                KC_SPC,           LT(1, KC_SPC),          KC_RALT, KC_RCTL
 ), [1] = LAYOUT_all(
 /* Function Layer 1: Nav
 ┌─────┐ ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┐    ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┬─────┐
 │ RST │ │     │ F1  │ F2  │ F3  │ F4  │ F5  │ F6  │    │ F7  │ F8  │ F9  │ F10 │ F11 │ F12 │ INS │ DEL │
 ├─────┤ ├─────┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┘  ┌─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴─────┤
 │     │ │       │ END │  ^  │HOME │PGUP │     │      │     │     │     │     │ |>  │ <<  │ >>  │       │
 ├─────┤ ├───────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     └─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴───────┤
 │     │ │        │ <-  │  v  │ ->  │PGDN │     │       │ <-  │  v  │  ^  │ ->  │ o)  │ o)} │           │
 ├─────┤ ├───────┬┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     ┌┴────┬┴────┬┴────┬┴────┬┴────┬┴────┬┴──────┬────┤
 │     │ │       │ │     │     │ CFG │     │ NUM │     │     │     │     │LDSKT│RDSKT│  Ø  │       │    │
 └─────┘ └───────┴─┼─────┼─────┴┬────┴─────┴─────┤     ├─────┴─────┴────┬┴─────┼─────┼─────┴───────┴────┘
                  │     │      │                │     │                │      │     │
                  └─────┴──────┴────────────────┘     └────────────────┴──────┴─────┘
 */
 RESET,   _______,   KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,    KC_F7,   KC_F8,   KC_F9,  KC_F10,  KC_F11,  KC_F12,  KC_INS,  KC_DEL,
 _______, _______,    KC_END,   KC_UP, KC_HOME, KC_PGUP, XXXXXXX,        XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_MPLY, KC_MPRV, KC_MNXT,  _______,
 _______, _______,    KC_LEFT, KC_DOWN, KC_RGHT, KC_PGDN, XXXXXXX,          KC_LEFT, KC_DOWN,   KC_UP, KC_RGHT, KC_VOLD, KC_VOLU,        _______,
 _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, TG(4), XXXXXXX, XXXXXXX, TG(2), XXXXXXX, XXXXXXX, LCTL(LGUI(KC_LEFT)), LCTL(LGUI(KC_RGHT)), KC_MUTE, _______,  _______,
                     _______, _______,               _______,                 _______,          _______, _______
 ), [2] = LAYOUT_all(
 /* Function Layer 2: Numpad example
 ┌─────┐ ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┐    ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┬─────┐
 │     │ │     │     │     │     │     │     │     │    │  7  │  8  │  9  │  0  │  -  │  +  │     │     │
 ├─────┤ ├─────┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┘  ┌─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴─────┤
 │     │ │       │     │     │     │     │     │      │  4  │  5  │  6  │     │  /  │  *  │     │       │
 ├─────┤ ├───────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     └─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴───────┤
 │     │ │        │     │     │     │     │     │       │  1  │  2  │  3  │     │     │     │ KP_ENTER  │
 ├─────┤ ├───────┬┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     ┌┴────┬┴────┬┴────┬┴────┬┴────┬┴────┬┴──────┬────┤
 │     │ │       │ │     │     │     │     │     │     │ ___ │  0  │  .  │     │     │     │       │    │
 └─────┘ └───────┴─┼─────┼─────┴┬────┴─────┴─────┤     ├─────┴─────┴────┬┴─────┼─────┼─────┴───────┴────┘
                  │     │      │                │     │                │      │     │
                  └─────┴──────┴────────────────┘     └────────────────┴──────┴─────┘
 */
 _______, _______, _______, _______, _______, _______, _______, _______,  KC_KP_7, KC_KP_8, KC_KP_9, KC_KP_0, KC_PMNS, KC_PPLS, _______, _______,
 _______, _______,   _______, _______, _______, _______, _______,        KC_KP_4, KC_KP_5, KC_KP_6, XXXXXXX, KC_PSLS, KC_PAST, _______,  _______,
 _______, _______,    _______, _______, _______, _______, _______,          KC_KP_1, KC_KP_2, KC_KP_3, XXXXXXX, _______, _______,        KC_PENT,
 _______, _______, _______, _______, _______, _______, _______, _______,   TG(2), KC_KP_0, KC_PDOT, _______, _______, _______, _______,  _______,
                     _______, _______,               _______,                 _______,          _______, _______
 ), [3] = LAYOUT_all(
 /* Function Layer 3
 ┌─────┐ ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┐    ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┬─────┐
 │     │ │     │     │     │     │     │     │     │    │     │     │     │     │     │     │     │     │
 ├─────┤ ├─────┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┘  ┌─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴─────┤
 │     │ │       │     │     │     │     │     │      │     │     │     │     │     │     │     │       │
 ├─────┤ ├───────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     └─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴───────┤
 │     │ │        │     │     │     │     │     │       │     │     │     │     │     │     │           │
 ├─────┤ ├───────┬┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     ┌┴────┬┴────┬┴────┬┴────┬┴────┬┴────┬┴──────┬────┤
 │     │ │       │ │     │     │     │     │     │     │     │     │     │     │     │     │       │    │
 └─────┘ └───────┴─┼─────┼─────┴┬────┴─────┴─────┤     ├─────┴─────┴────┬┴─────┼─────┼─────┴───────┴────┘
                  │     │      │                │     │                │      │     │
                  └─────┴──────┴────────────────┘     └────────────────┴──────┴─────┘
 */
 _______, _______, _______, _______, _______, _______, _______, _______,  _______, _______, _______, _______, _______, _______, _______, _______,
 _______, _______,   _______, _______, _______, _______, _______,        _______, _______, _______, _______, _______, _______, _______,  _______,
 _______, _______,    _______, _______, _______, _______, _______,          _______, _______, _______, _______, _______, _______,        _______,
 _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,  _______,
                     _______, _______,               _______,                 _______,          _______, _______
 ), [4] = LAYOUT_all(
 /* Function Layer 4: Firmware Config
 ┌─────┐ ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┐    ┌─────┬─────┬─────┬─────┬─────┬─────┬─────┬─────┐
 │ RST │ │     │     │     │     │     │     │     │    │     │     │     │     │     │     │     │     │
 ├─────┤ ├─────┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┘  ┌─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴───┬─┴─────┤
 │     │ │       │ RGB │RGB+ │RGB- │HUE+ │HUE- │      │     │     │     │     │     │     │     │       │
 ├─────┤ ├───────┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     └─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴─┬───┴───────┤
 │     │ │        │     │SPD+ │SPD- │SAT+ │SAT- │       │     │     │     │     │     │     │           │
 ├─────┤ ├───────┬┴┬────┴┬────┴┬────┴┬────┴┬────┴┐     ┌┴────┬┴────┬┴────┬┴────┬┴────┬┴────┬┴──────┬────┤
 │     │ │       │ │     │     │ ___ │VAL+ │VAL- │     │     │     │     │     │     │     │       │    │
 └─────┘ └───────┴─┼─────┼─────┴┬────┴─────┴─────┤     ├─────┴─────┴────┬┴─────┼─────┼─────┴───────┴────┘
                  │     │      │                │     │                │      │     │
                  └─────┴──────┴────────────────┘     └────────────────┴──────┴─────┘
 */
 RESET,   XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,  XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,
 XXXXXXX, XXXXXXX,  RGB_TOG, RGB_MOD, RGB_RMOD, RGB_HUI, RGB_HUD,        XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,  XXXXXXX,
 XXXXXXX, XXXXXXX,    XXXXXXX, RGB_SPI, RGB_SPD, RGB_SAI, RGB_SAD,          XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,        XXXXXXX,
 XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,   TG(4), RGB_VAI, RGB_VAD, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,  _______,
                     XXXXXXX, XXXXXXX,               XXXXXXX,                 _______,          XXXXXXX, XXXXXXX
 ) };
@@ -0,0 +1 @@
 VIA_ENABLE = yes
@@ -0,0 +1,29 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "config_common.h"
 #define DEVICE_VER      0x0001
 #define MATRIX_ROW_PINS \
    { D4, D7, B6, B4, B7 }
 #define MATRIX_COL_PINS \
    { F1, B0, B1, B2, B3, D0, D1, D2, C6, C7, F7, F6, F5, F4, B5 }
 #define UNUSED_PINS \
    { D4, D5, F0, B7 }
 #define RGB_DI_PIN E6
@@ -0,0 +1,16 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include "rev1.h"
@@ -0,0 +1,18 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "quantum.h"
@@ -0,0 +1,21 @@
 # MCU name
 MCU = atmega32u4
 # Bootloader selection
 BOOTLOADER = atmel-dfu
 # Build Options
 #   change yes to no to disable
 #
 BOOTMAGIC_ENABLE      = lite
 MOUSEKEY_ENABLE       = no
 EXTRAKEY_ENABLE       = yes
 CONSOLE_ENABLE        = no
 COMMAND_ENABLE        = no
 SLEEP_LED_ENABLE      = yes
 SPLIT_KEYBOARD        = no
 BACKLIGHT_ENABLE      = no
 NKRO_ENABLE           = yes
 RGBLIGHT_ENABLE       = yes
 AUDIO_ENABLE          = no
 LTO_ENABLE            = yes
@@ -0,0 +1,29 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "config_common.h"
 #define DEVICE_VER      0x0002
 #define MATRIX_ROW_PINS \
    { F4, F5, D7, B5, B4 }
 #define MATRIX_COL_PINS \
    { F6, B0, B1, F7, C7, C6, B6, F1, B2, B3, D6, D3, D2, D1, D0 } 
 #define UNUSED_PINS \
    { D4, D5, F0, B7 }
 #define RGB_DI_PIN E6
@@ -0,0 +1,16 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include "rev2.h"
@@ -0,0 +1,18 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "quantum.h"
@@ -0,0 +1,21 @@
 # MCU name
 MCU = atmega32u4
 # Bootloader selection
 BOOTLOADER = atmel-dfu
 # Build Options
 #   change yes to no to disable
 #
 BOOTMAGIC_ENABLE      = lite
 MOUSEKEY_ENABLE       = no
 EXTRAKEY_ENABLE       = yes
 CONSOLE_ENABLE        = no
 COMMAND_ENABLE        = no
 SLEEP_LED_ENABLE      = yes
 SPLIT_KEYBOARD        = no
 BACKLIGHT_ENABLE      = no
 NKRO_ENABLE           = yes
 RGBLIGHT_ENABLE       = yes
 AUDIO_ENABLE          = no
 LTO_ENABLE            = yes
@@ -0,0 +1,29 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "config_common.h"
 #define DEVICE_VER      0x0003
 #define MATRIX_ROW_PINS \
    { F1, B4, B5, D6, D7 }
 #define MATRIX_COL_PINS \
    { B6, C6, C7, F7, F6, F5, F4, F0, B7, D0, D1, D2, D3, D5, D4 } 
 #define UNUSED_PINS \
    { D0, B1, B2, B3 }
 #define RGB_DI_PIN E6
@@ -0,0 +1,16 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include "rev3.h"
@@ -0,0 +1,24 @@
 /* Copyright 2020 bemeier
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "quantum.h"
 /*
 PCB rev3 has a number of layout options that rev2 and rev1 don't have,
 however, to me just using "ALL_67" for all for all keymaps seems easier to
 maintain than adding all possible permutations of layout options here.
 */
@@ -0,0 +1,21 @@
 # MCU name
 MCU = atmega32u4
 # Bootloader selection
 BOOTLOADER = atmel-dfu
 # Build Options
 #   change yes to no to disable
 #
 BOOTMAGIC_ENABLE      = lite
 MOUSEKEY_ENABLE       = no
 EXTRAKEY_ENABLE       = yes
 CONSOLE_ENABLE        = no
 COMMAND_ENABLE        = no
 SLEEP_LED_ENABLE      = yes
 SPLIT_KEYBOARD        = no
 BACKLIGHT_ENABLE      = no
 NKRO_ENABLE           = yes
 RGBLIGHT_ENABLE       = yes
 AUDIO_ENABLE          = no
 LTO_ENABLE            = yes
@@ -0,0 +1,16 @@
 /* Copyright 2020 BINEPAD
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include "bn003.h"
@@ -0,0 +1,23 @@
 /* Copyright 2020 BINEPAD
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #include "quantum.h"
 #define LAYOUT( \
    K00, K01, K02 \
 ) { \
    { K00, K01, K02 } \
 }
@@ -0,0 +1,89 @@
 /* Copyright 2020 BINEPAD
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 #include "config_common.h"
 /* USB Device descriptor parameter */
 #define VENDOR_ID       0x4249 // Binepad
 #define PRODUCT_ID      0x4287
 #define DEVICE_VER      0x0001
 #define MANUFACTURER    Binepad
 #define PRODUCT         BN003
 /* Key matrix size */
 #define MATRIX_ROWS 1
 #define MATRIX_COLS 3
 #define MATRIX_ROW_PINS { C6 }
 #define MATRIX_COL_PINS { B4, B5, B6 }
 #define UNUSED_PINS
 /* COL2ROW, ROW2COL*/
 #define DIODE_DIRECTION COL2ROW
 /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
 #define DEBOUNCE 5
 /* define if matrix has ghost (lacks anti-ghosting diodes) */
 //#define MATRIX_HAS_GHOST
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 /* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
 * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
 */
 // #define GRAVE_ESC_CTRL_OVERRIDE
 /*
 * Force NKRO
 *
 * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
 * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
 * makefile for this to work.)
 *
 * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
 * until the next keyboard reset.
 *
 * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
 * fully operational during normal computer usage.
 *
 * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
 * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
 * bootmagic, NKRO mode will always be enabled until it is toggled again during a
 * power-up.
 *
 */
 //#define FORCE_NKRO
 /*
 * Magic Key Options
 *
 * Magic keys are hotkey commands that allow control over firmware functions of
 * the keyboard. They are best used in combination with the HID Listen program,
 * found here: https://www.pjrc.com/teensy/hid_listen.html
 *
 * The options below allow the magic key functionality to be changed. This is
 * useful if your keyboard/keypad is missing keys and you want magic key support.
 *
 */
@@ -0,0 +1,28 @@
 {
  "keyboard_name": "BN003",
  "url": "https://binepad.com",
  "maintainer": "binepad",
  "width": 3,
  "height": 1,
  "layouts": {
    "LAYOUT": {
      "layout": [
        {
          "label": "K0",
          "x": 0,
          "y": 0
        },
        {
          "label": "K1",
          "x": 1,
          "y": 0
        },
        {
          "label": "K2",
          "x": 2,
          "y": 0
        }
      ]
    }
  }
 }
@@ -0,0 +1,19 @@
 #include QMK_KEYBOARD_H
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    [0] = LAYOUT(
        KC_0,
        KC_1,
        KC_2
    ),
    [1] = LAYOUT(
        KC_NO,
        KC_NO,
        KC_NO
    ),
    [2] = LAYOUT(
        KC_NO,
        KC_NO,
        KC_NO
    )
 };
@@ -0,0 +1 @@
 # bn003 - Default layout
@@ -0,0 +1,24 @@
 #include QMK_KEYBOARD_H
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
    [0] = LAYOUT(
        KC_0,
        KC_1,
        KC_2
    ),
    [1] = LAYOUT(
        KC_NO,
        KC_NO,
        KC_NO
    ),
    [2] = LAYOUT(
        KC_NO,
        KC_NO,
        KC_NO
    ),
    [3] = LAYOUT(
        KC_NO,
        KC_NO,
        KC_NO
    )
 };
@@ -0,0 +1 @@
 VIA_ENABLE = yes
@@ -0,0 +1,15 @@
 # BINEPAD BN003
 ![BINEPAD BN003](https://imgur.com/q8JPcNEl.jpg)
 A 3% macropad.
 * Keyboard Maintainer: [BINEPAD]
 * Hardware Supported: BN003 PCB (ATmega32U4)
 * Hardware Availability: [Interest Check](https://www.binepad.com/bn003)
 Make example for this keyboard (after setting up your build environment):
    make binepad/bn003:default
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
@@ -0,0 +1,22 @@
 # MCU name
 MCU = atmega32u4
 # Bootloader selection
 BOOTLOADER = atmel-dfu
 # Build Options
 #   change yes to no to disable
 #
 BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration
 MOUSEKEY_ENABLE = yes       # Mouse keys
 EXTRAKEY_ENABLE = yes       # Audio control and System control
 CONSOLE_ENABLE = yes        # Console for debug
 COMMAND_ENABLE = yes        # Commands for debug and configuration
 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
 NKRO_ENABLE = yes           # USB Nkey Rollover
 BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
 RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
 BLUETOOTH_ENABLE = no       # Enable Bluetooth
 AUDIO_ENABLE = no           # Audio output
@@ -0,0 +1,36 @@
 #include QMK_KEYBOARD_H
 enum layers {
    _MAIN,
    _RAISE,
    _LOWER,
 };
 // Readability keycodes
 #define LOWER   MO(_LOWER)
 #define RAISE   MO(_RAISE)
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  [_MAIN] = LAYOUT_ortho_4x12(
    KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC,
    KC_ESC,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,
    KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_ENT ,
    KC_PIPE, KC_LCTL, KC_LALT, KC_LGUI, LOWER,   KC_SPC,  KC_SPC,  RAISE,   KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT
  ),
  [_RAISE] = LAYOUT_ortho_4x12(
  KC_TILD, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR,    KC_ASTR,    KC_LPRN, KC_RPRN, KC_BSPC,
  KC_DEL,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_UNDS,    KC_PLUS,    KC_LCBR, KC_RCBR, KC_PIPE,
  _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  S(KC_NUHS), S(KC_NUBS), KC_HOME, KC_END,  _______,
  RESET,   _______, _______, _______, _______, _______, _______, _______,    KC_MNXT,    KC_VOLD, KC_VOLU, KC_MPLY
  ),
  [_LOWER] = LAYOUT_ortho_4x12(
 KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_BSPC,
 KC_DEL,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_BSLS,
 _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_NUHS, KC_NUBS, KC_PGUP, KC_PGDN, _______,
 _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY
  )
 };
@@ -0,0 +1,5 @@
 # The via keymap for boardsource 4x12 ortholinear keybaoard
 This folder contains the [VIA](https://caniusevia.com/) configuration for the boardsource 4x12 ortholinear keybaoard
 Maintained by: [gwillad](https://github.com/gwillad)
@@ -0,0 +1 @@
 VIA_ENABLE = yes
@@ -56,7 +56,7 @@ Ported to QMK by Peter Roe <[email protected]>
    { K38,   K39,   K3A,   K3B, K3C,   K3D,   K3E,   KC_NO, }, \
    { KC_NO, K41,   KC_NO, K43, KC_NO, K45,   KC_NO, K47    }, \
    { KC_NO, KC_NO, KC_NO, K4B, K4C,   KC_NO, K4E,   KC_NO, }, \
-    { KC_NO, KC_NO, K52,   K53, K54,   K55,   K56,   K57    }, \
+    { KC_NO, K51,   K52,   K53, K54,   K55,   K56,   K57    }, \
    { K58,   K59,   KC_NO, K5B, K5C,   KC_NO, KC_NO, KC_NO, }, \
    { K60,   K61,   K62,   K63, K64,   K65,   KC_NO, K67    }, \
    { KC_NO, K69,   KC_NO, K6B, KC_NO, K6D,   KC_NO, K6F    }, \
@@ -0,0 +1,33 @@
 /*
 This is the c configuration file for the keymap
 Copyright 2012 Jun Wako <[email protected]>
 Copyright 2015 Jack Humbert
 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
 the Free Software Foundation, either version 2 of the License, or
 (at your option) any later version.
 This program is distributed in the hope that it will be useful,
 but WITHOUT ANY WARRANTY; without even the implied warranty of
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 GNU General Public License for more details.
 You should have received a copy of the GNU General Public License
 along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
 #pragma once
 /* Use I2C or Serial, not both */
 #define USE_SERIAL
 // #define USE_I2C
 /* Select hand configuration */
 #define MASTER_LEFT
 // #define MASTER_RIGHT
 // #define EE_HANDS
@@ -0,0 +1,141 @@
 /* Copyright 2020 Toyoshima Hidenori <[email protected]>
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>
 */
 #include QMK_KEYBOARD_H
 enum layers {
    _QWERTY,
    _LOWER,
    _RAISE,
    _ADJUST,
 };
 enum custom_keycodes {
    QWERTY = SAFE_RANGE,
    LOWER,
    RAISE,
    ADJUST,
 };
 #define EISU LALT(KC_GRV)
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  /* Qwerty
   * ,----------------------------------------------------------------------------------------------------------------------.
   * |  TAB |   Q  |   W  |   E  |   R  |   T  |   -  |                    |   =  |   Y  |   U  |   I  |   O  |   P  |  \   |
   * |------+------+------+------+------+------+------+--------------------+------+------+------+------+------+------+------|
   * | Ctrl |   A  |   S  |   D  |   F  |   G  |   [  |                    |   ]  |   H  |   J  |   K  |   L  |   ;  |  '   |
   * |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
   * | Shift|   Z  |   X  |   C  |   V  |   B  |  GUI |                    |  GUI |   N  |   M  |   ,  |   .  |   /  | Shift|
   * |-------------+------+------+------+------+------+------+------+------+------+------+------+------+------+-------------|
   * | Ctrl |  ESC |  ALt | ESC  |||||||| Shift| Raise| Space|||||||| enter| Lower| Bcspc|||||||| Left | Down |  Up  | Right|
   * ,----------------------------------------------------------------------------------------------------------------------.
   */
    [_QWERTY] = LAYOUT(
    KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_MINS,                        KC_EQL , KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSLS,
    KC_LCTL, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_LBRC,                        KC_RBRC, KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT,
    KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_LGUI,                        KC_RGUI, KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,
    KC_LCTL, KC_ESC,  KC_LALT, KC_ESC,           KC_LSFT, RAISE,   KC_SPC,        KC_ENT, LOWER,   KC_BSPC,          KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT
  ),
  /* Lower
   * ,----------------------------------------------------------------------------------------------------------------------.
   * |   ~  |   1  |   2  |   3  |   4  |   5  |   _  |                    |   +  | 6    | 7    |  8   | 9    |   0  |   |  |
   * |------+------+------+------+------+------+------+--------------------+------+------+------+------+------+------+------|
   * | Ctrl |   ^  |   &  |   *  |   (  |   )  |   {  |                    |   }  | Left | Down |  Up  | Right|   :  |  "   |
   * |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
   * | Shift|   !  |   @  |   #  |   $  |   %  |  GUI |                    |  GUI |   -  |   =  |   <  |   >  |   ?  | Shift|
   * |-------------+------+------+------+------+------+------+------+------+------+------+------+------+------+-------------|
   * | Ctrl |  ESC |  ALt | EISU |||||||| kana | Raise| Space|||||||| Enter| Lower|Delete|||||||| Home |PageDn|PageUp|  End |
   * ,----------------------------------------------------------------------------------------------------------------------.
   */
  [_LOWER] = LAYOUT(
    KC_TILD, KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_UNDS,                       KC_PLUS, KC_6,    KC_7,    KC_8,   KC_9,    KC_0,    KC_PIPE,
    KC_LCTL, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_LCBR,                       KC_RCBR, KC_LEFT, KC_DOWN, KC_UP,  KC_RGHT, KC_COLN, KC_DQT ,
    KC_LSFT, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_LGUI,                       KC_RGUI, KC_MINS, KC_EQL,  KC_LT,  KC_GT,   KC_QUES, KC_RSFT,
    KC_LCTL, KC_ESC, KC_LALT,  KC_LANG2,         KC_LANG1,RAISE,   KC_SPC,       KC_ENT, LOWER,   KC_DEL,           KC_HOME,KC_PGDN, KC_PGUP, KC_END
  ),
  /* Raise
   * ,----------------------------------------------------------------------------------------------------------------------.
   * |   `  |   1  |   2  |   3  |   4  |   5  |   _  |                    |   +  | 6    | 7    |  8   | 9    |   0  |   |  |
   * |------+------+------+------+------+------+------+--------------------+------+------+------+------+------+------+------|
   * | Ctrl |   ^  |   &  |   *  |   (  |   )  |   {  |                    |   }  | Left | Down |  Up  | Right|   :  |  "   |
   * |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
   * | Shift|   !  |   @  |   #  |   $  |   %  |  GUI |                    |  GUI |   _  |   +  |   <  |   >  |   ?  | Shift|
   * |-------------+------+------+------+------+------+------+------+------+------+------+------+------+------+-------------|
   * | Ctrl |  ESC |  ALt | EISU |||||||| kana | Raise| Space|||||||| Enter| Lower|Delete|||||||| Home |PageDn|PageUp|  End |
   * ,----------------------------------------------------------------------------------------------------------------------.
  */
  [_RAISE] = LAYOUT(
    KC_GRV , KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_UNDS,                       KC_PLUS, KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_PIPE,
    KC_LCTL, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_LCBR,                       KC_RCBR, KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT, KC_COLN, KC_DQT ,
    KC_LSFT, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_LGUI,                       KC_RGUI, KC_UNDS, KC_PLUS, KC_LT,   KC_GT,   KC_QUES, KC_RSFT,
    KC_LCTL, KC_ESC,  KC_LALT, KC_LANG2,         KC_LANG1,RAISE,   KC_SPC,       KC_ENT, LOWER,   KC_DEL,           KC_HOME, KC_PGDN, KC_PGUP, KC_END
  ),
  /* Adjust
   * ,----------------------------------------------------------------------------------------------------------------------.
   * |      | Reset|RGB ON|  MODE|  HUE-|  HUE+|      |                    |      |  SAT-|  SAT+|  VAL-|  VAL+|      |      |
   * |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
   * |      |                                  |      |                    |      |      |      |      |      |      |      |
   * |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
   * |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |      |                    |      |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |
   * |-------------+------+------+------+------+------+------+------+------+------+------+------+------+------+-------------|
   * |      |      |      |      ||||||||      |      |      ||||||||      |      |      ||||||||      |      |      |      |
   * ,----------------------------------------------------------------------------------------------------------------------.
   */
  [_ADJUST] = LAYOUT(
    _______, RESET  , RGB_TOG, RGB_MOD, RGB_HUD, RGB_HUI,_______,                       _______, RGB_SAD, RGB_SAI, RGB_VAD, RGB_VAI, _______, _______,
    _______, _______, BL_TOGG, BL_BRTG, BL_INC , BL_DEC ,_______,                       _______, _______, _______, _______, _______, _______, _______,
    KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,    KC_F6 ,_______,                       _______, KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,
    _______, _______, _______, _______,          _______,_______,_______,       _______,_______, _______,          _______, _______, _______, _______
  )
 };
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
  switch (keycode) {
    case LOWER:
      if (record->event.pressed) {
        layer_on(_LOWER);
        update_tri_layer(_LOWER, _RAISE, _ADJUST);
      } else {
        layer_off(_LOWER);
        update_tri_layer(_LOWER, _RAISE, _ADJUST);
      }
      return false;
      break;
    case RAISE:
      if (record->event.pressed) {
        layer_on(_RAISE);
        update_tri_layer(_LOWER, _RAISE, _ADJUST);
      } else {
        layer_off(_RAISE);
        update_tri_layer(_LOWER, _RAISE, _ADJUST);
      }
      return false;
      break;
    case ADJUST:
      if (record->event.pressed) {
        layer_on(_ADJUST);
      } else {
        layer_off(_ADJUST);
      }
      return false;
      break;
  }
  return true;
 }
@@ -0,0 +1,62 @@
 # ToyoshimaHidenori's keymap for Ergodash mini
 This is the ToyoshimaHidenori's keymap configuration for Ergodash mini.
 There are four layers, QWERTY(default), LOWER, RAISE and ADJSUT.
 ## Layers
 ### Qwerty
 ```
 ,----------------------------------------------------------------------------------------------------------------------.
 |  TAB |   Q  |   W  |   E  |   R  |   T  |   -  |                    |   =  |   Y  |   U  |   I  |   O  |   P  |  \   |
 |------+------+------+------+------+------+------+--------------------+------+------+------+------+------+------+------|
 | Ctrl |   A  |   S  |   D  |   F  |   G  |   [  |                    |   ]  |   H  |   J  |   K  |   L  |   ;  |  '   |
 |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
 | Shift|   Z  |   X  |   C  |   V  |   B  |  GUI |                    |  GUI |   N  |   M  |   ,  |   .  |   /  | Shift|
 |-------------+------+------+------+------+------+------+------+------+------+------+------+------+------+-------------|
 | Ctrl |  ESC |  ALt | ESC  |||||||| Shift| Raise| Space|||||||| enter| Lower| Bcspc|||||||| Left | Down |  Up  | Right|
 ,----------------------------------------------------------------------------------------------------------------------.
 ```
 ### Lower
 ```
 ,----------------------------------------------------------------------------------------------------------------------.
 |   ~  |   1  |   2  |   3  |   4  |   5  |   _  |                    |   +  | 6    | 7    |  8   | 9    |   0  |   |  |
 |------+------+------+------+------+------+------+--------------------+------+------+------+------+------+------+------|
 | Ctrl |   ^  |   &  |   *  |   (  |   )  |   {  |                    |   }  | Left | Down |  Up  | Right|   :  |  "   |
 |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
 | Shift|   !  |   @  |   #  |   $  |   %  |  GUI |                    |  GUI |   -  |   =  |   <  |   >  |   ?  | Shift|
 |-------------+------+------+------+------+------+------+------+------+------+------+------+------+------+-------------|
 | Ctrl |  ESC |  ALt | EISU |||||||| kana | Raise| Space|||||||| Enter| Lower|Delete|||||||| Home |PageDn|PageUp|  End |
 ,----------------------------------------------------------------------------------------------------------------------.
 ```
 ### Raise
 ```
 ,----------------------------------------------------------------------------------------------------------------------.
 |   `  |   1  |   2  |   3  |   4  |   5  |   _  |                    |   +  | 6    | 7    |  8   | 9    |   0  |   |  |
 |------+------+------+------+------+------+------+--------------------+------+------+------+------+------+------+------|
 | Ctrl |   ^  |   &  |   *  |   (  |   )  |   {  |                    |   }  | Left | Down |  Up  | Right|   :  |  "   |
 |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
 | Shift|   !  |   @  |   #  |   $  |   %  |  GUI |                    |  GUI |   _  |   +  |   <  |   >  |   ?  | Shift|
 |-------------+------+------+------+------+------+------+------+------+------+------+------+------+------+-------------|
 | Ctrl |  ESC |  ALt | EISU |||||||| kana | Raise| Space|||||||| Enter| Lower|Delete|||||||| Home |PageDn|PageUp|  End |
 ,----------------------------------------------------------------------------------------------------------------------.
 ```
 ### Adjust
 ```
 ,----------------------------------------------------------------------------------------------------------------------.
 |      | Reset|RGB ON|  MODE|  HUE-|  HUE+|      |                    |      |  SAT-|  SAT+|  VAL-|  VAL+|      |      |
 |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
 |      |                                  |      |                    |      |      |      |      |      |      |      |
 |------+------+------+------+------+------+---------------------------+------+------+------+------+------+------+------|
 |  F1  |  F2  |  F3  |  F4  |  F5  |  F6  |      |                    |      |  F7  |  F8  |  F9  |  F10 |  F11 |  F12 |
 |-------------+------+------+------+------+------+------+------+------+------+------+------+------+------+-------------|
 |      |      |      |      ||||||||      |      |      ||||||||      |      |      ||||||||      |      |      |      |
 ,----------------------------------------------------------------------------------------------------------------------.
 ```
@@ -0,0 +1,3 @@
 BACKLIGHT_ENABLE = yes
 RGBLIGHT_ENABLE = yes
 AUDIO_ENABLE = no
@@ -18,6 +18,9 @@
 #undef MOUSEKEY_WHEEL_INTERVAL
 #define MOUSEKEY_WHEEL_INTERVAL 50
 #undef MK_COMBINED
 #define MK_COMBINED
 // /* Temporarily defining a tapping term that is ridiculous to see if i can tell if lt is working. */
 // #undef TAPPING_TERM
 // #define TAPPING_TERM 499
@@ -28,13 +28,17 @@
 enum custom_keycodes {
  RGB_SLD = EZ_SAFE_RANGE,
  MS_WH_UP,
  MS_WH_DOWN,
  MS_WH_RIGHT,
  MS_WH_LEFT,
 };
 // tapdance keycodes
 enum td_keycodes {
  CTRL_TO12,
  SHIFT_TO13,
-  ALT_TO11
+  ALT_TO11,
 };
 // define a type containing as many tapdance states as you need
@@ -59,6 +63,7 @@ void altto11_reset (qk_tap_dance_state_t *state, void *user_data);
 void shiftto13_finished (qk_tap_dance_state_t *state, void *user_data);
 void shiftto13_reset (qk_tap_dance_state_t *state, void *user_data);
 const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  [0] = LAYOUT_ergodox_pretty(
    KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,                                          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,
@@ -162,9 +167,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  ),
  [10] = LAYOUT_ergodox_pretty(
    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,
-    KC_TRANSPARENT, KC_NO,          KC_LGUI,        KC_MS_BTN2,     KC_NO,          KC_NO,          KC_TRANSPARENT,                                 MT(MOD_RCTL, KC_A), KC_NO,      KC_NO,          KC_MS_UP,       KC_NO,          KC_NO,          KC_TRANSPARENT,
+    KC_TRANSPARENT, KC_NO,          KC_LGUI,        KC_MS_BTN2,     KC_ACL2,        KC_NO,          KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_NO,          KC_NO,          KC_MS_UP,       KC_NO,          KC_NO,          KC_TRANSPARENT,
    KC_TRANSPARENT, TD(SHIFT_TO13), TD(CTRL_TO12),  TD(ALT_TO11),   KC_MS_BTN1,     KC_NO,                                                                          KC_NO,          KC_MS_LEFT,     KC_MS_DOWN,     KC_MS_RIGHT,    KC_NO,          KC_TRANSPARENT,
-    KC_TRANSPARENT, KC_NO,          MT(MOD_LGUI | MOD_LCTL,KC_NO),  KC_NO, KC_NO,   KC_NO,          KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_TRANSPARENT,
+    KC_TRANSPARENT, KC_NO,          MT(MOD_LGUI | MOD_LCTL,KC_NO),  KC_ACL0, KC_NO, KC_NO,          KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_TRANSPARENT,
    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,                                                                                                 KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,
                                                                                                    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,
                                                                                                                    KC_TRANSPARENT, KC_TRANSPARENT,
@@ -182,9 +187,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
  ),
  [12] = LAYOUT_ergodox_pretty(
    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,
-    KC_TRANSPARENT, KC_NO,          KC_LGUI,        KC_HYPR,        KC_NO,          KC_NO,          KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_NO,          KC_NO,          KC_MS_WH_UP,    KC_NO,          KC_NO,          KC_TRANSPARENT,
+    KC_TRANSPARENT, KC_NO,          KC_LGUI,        KC_HYPR,        KC_ACL2,        KC_NO,          KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_NO,          KC_NO,          KC_MS_WH_UP,    KC_NO,          KC_NO,          KC_TRANSPARENT,
    KC_TRANSPARENT, KC_LSHIFT,      KC_LCTRL,       KC_LALT,        KC_NO,          KC_NO,                                                                          KC_NO,          KC_MS_WH_LEFT,  KC_MS_WH_DOWN,  KC_MS_WH_RIGHT, KC_NO,          KC_TRANSPARENT,
-    KC_TRANSPARENT, KC_NO,          MT(MOD_LGUI | MOD_LCTL,KC_NO),  KC_NO, KC_NO,   KC_NO,          KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_TRANSPARENT,
+    KC_TRANSPARENT, KC_NO,          MT(MOD_LGUI | MOD_LCTL,KC_NO),  MO(14), KC_NO,  KC_NO,          KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_TRANSPARENT,
    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,                                                                                                 KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,
                                                                                                    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,
                                                                                                                    KC_TRANSPARENT, KC_TRANSPARENT,
@@ -200,16 +205,18 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
                                                                                                                    KC_TRANSPARENT, KC_TRANSPARENT,
                                                                                    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, TO(0)
  ),
  [14] = LAYOUT_ergodox_pretty(
    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,
    KC_TRANSPARENT, KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_NO,          KC_NO,          MS_WH_UP,   KC_NO,          KC_NO,          KC_TRANSPARENT,
    KC_TRANSPARENT, KC_NO,          KC_NO,          KC_NO,          KC_NO,          KC_NO,                                                                          KC_NO,          MS_WH_LEFT,     MS_WH_DOWN, MS_WH_RIGHT,    KC_NO,          KC_TRANSPARENT,
    KC_TRANSPARENT, KC_NO,          KC_NO,          KC_TRANSPARENT, KC_NO,          KC_NO,          KC_TRANSPARENT,                                 KC_TRANSPARENT, KC_NO,          KC_NO,          KC_NO,      KC_NO,          KC_NO,          KC_TRANSPARENT,
    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,                                                                                                 KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,
                                                                                                    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT,
                                                                                                                    KC_TRANSPARENT, KC_TRANSPARENT,
                                                                                    KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT, KC_TRANSPARENT
  ),
 };
 /* Commenting out for debug purposes */
 // bool process_record_user(uint16_t keycode, keyrecord_t *record) {
 //   switch (keycode) {
 //   }
 //   return true;
 // }
 uint32_t layer_state_set_user(uint32_t state) {
  uint8_t layer = biton32(state);
  ergodox_board_led_off();
@@ -252,11 +259,31 @@ uint32_t layer_state_set_user(uint32_t state) {
 // determine the tapdance state to return
 int cur_dance (qk_tap_dance_state_t *state) {
  if (state->count == 1) {
-    if (state->interrupted || !state->pressed) { return SINGLE_TAP; }
+    if (state->interrupted && state->pressed && state->interrupting_keycode == KC_MS_BTN1) {return SINGLE_HOLD;}
    if (state->interrupted && state->pressed && state->interrupting_keycode == 22273) {return SINGLE_HOLD;}
    if (state->interrupted && state->pressed && state->interrupting_keycode == 22272) {return SINGLE_HOLD;}
    if (state->interrupted && state->pressed && state->interrupting_keycode == KC_TAB) {return SINGLE_HOLD;}
    else if (state->interrupted || !state->pressed) {
        // if (state->interrupted) {
        //     print("interrupted\n");
        //     uprintf("Shift: %u\n", KC_LSHIFT);
        //     uprintf("Control: %u\n", KC_LCTRL);
        //     uprintf("%u\n",state->interrupting_keycode);
        // }
        return SINGLE_TAP;
    }
    else { return SINGLE_HOLD; }
  }
  else { return 2; } // any number higher than the maximum state value you return above
 }
 // /* Backup in case previous code is hard to piece together. */
 // int cur_dance (qk_tap_dance_state_t *state) {
 //   if (state->count == 1) {
 //     if (state->interrupted || !state->pressed) { return SINGLE_TAP; }
 //     else { return SINGLE_HOLD; }
 //   }
 //   else { return 2; } // any number higher than the maximum state value you return above
 // }
 void ctrlto12_finished (qk_tap_dance_state_t *state, void *user_data) {
  td_state = cur_dance(state);
@@ -265,7 +292,14 @@ void ctrlto12_finished (qk_tap_dance_state_t *state, void *user_data) {
      layer_on(12);
      break;
    case SINGLE_HOLD:
      if (state->interrupted && (state->interrupting_keycode == 22273 || state->interrupting_keycode == 43)) {
        register_mods(MOD_BIT(KC_LCTRL));
        break;
      }
      register_mods(MOD_BIT(KC_LCTRL)); // for a layer-tap key, use `layer_on(_MY_LAYER)` here
      if (state->interrupted && state->interrupting_keycode == KC_MS_BTN1) {
        register_code16(LCTL(KC_MS_BTN1));
      }
      break;
  }
 }
@@ -275,7 +309,14 @@ void ctrlto12_reset (qk_tap_dance_state_t *state, void *user_data) {
    case SINGLE_TAP:
      break;
    case SINGLE_HOLD:
      if (state->interrupted && (state->interrupting_keycode == 22273 || state->interrupting_keycode == 43) ) {
        unregister_mods(MOD_BIT(KC_LCTRL));
        break;
      }
      unregister_mods(MOD_BIT(KC_LCTRL)); // for a layer-tap key, use `layer_off(_MY_LAYER)` here
      if (state->interrupted && state->interrupting_keycode == KC_MS_BTN1) {
        unregister_code16(LCTL(KC_MS_BTN1));
      }
      break;
  }
 }
@@ -287,7 +328,14 @@ void shiftto13_finished (qk_tap_dance_state_t *state, void *user_data) {
      layer_on(13);
      break;
    case SINGLE_HOLD:
      if (state->interrupted && (state->interrupting_keycode == 22272 || state->interrupting_keycode == 43) ) {
        register_mods(MOD_BIT(KC_LSHIFT));
        break;
      }
      register_mods(MOD_BIT(KC_LSHIFT)); // for a layer-tap key, use `layer_on(_MY_LAYER)` here
      if (state->interrupted && state->interrupting_keycode == KC_MS_BTN1) {
        register_code16(LSFT(KC_MS_BTN1));
      }
      break;
  }
 }
@@ -297,7 +345,14 @@ void shiftto13_reset (qk_tap_dance_state_t *state, void *user_data) {
    case SINGLE_TAP:
      break;
    case SINGLE_HOLD:
      if (state->interrupted && (state->interrupting_keycode == 22272 || state->interrupting_keycode == 43) ) {
        unregister_mods(MOD_BIT(KC_LSHIFT));
        break;
      }
      unregister_mods(MOD_BIT(KC_LSHIFT)); // for a layer-tap key, use `layer_off(_MY_LAYER)` here
      if (state->interrupted && state->interrupting_keycode == KC_MS_BTN1) {
        unregister_code16(LSFT(KC_MS_BTN1));
      }
      break;
  }
 }
@@ -310,6 +365,9 @@ void altto11_finished (qk_tap_dance_state_t *state, void *user_data) {
      break;
    case SINGLE_HOLD:
      register_mods(MOD_BIT(KC_LALT)); // for a layer-tap key, use `layer_on(_MY_LAYER)` here
      if (state->interrupted && state->interrupting_keycode == KC_MS_BTN1) {
        register_code16(LALT(KC_MS_BTN1));
      }
      break;
  }
 }
@@ -320,6 +378,9 @@ void altto11_reset (qk_tap_dance_state_t *state, void *user_data) {
      break;
    case SINGLE_HOLD:
      unregister_mods(MOD_BIT(KC_LALT)); // for a layer-tap key, use `layer_off(_MY_LAYER)` here
      if (state->interrupted && state->interrupting_keycode == KC_MS_BTN1) {
        unregister_code16(LALT(KC_MS_BTN1));
      }
      break;
  }
 }
@@ -328,7 +389,7 @@ void altto11_reset (qk_tap_dance_state_t *state, void *user_data) {
 qk_tap_dance_action_t tap_dance_actions[] = {
  [CTRL_TO12] = ACTION_TAP_DANCE_FN_ADVANCED(NULL, ctrlto12_finished, ctrlto12_reset),
  [SHIFT_TO13] = ACTION_TAP_DANCE_FN_ADVANCED(NULL, shiftto13_finished, shiftto13_reset),
-  [ALT_TO11] = ACTION_TAP_DANCE_FN_ADVANCED(NULL, altto11_finished, altto11_reset)
+  [ALT_TO11] = ACTION_TAP_DANCE_FN_ADVANCED(NULL, altto11_finished, altto11_reset),
 };
 /* Debugging functions */
@@ -342,10 +403,32 @@ void keyboard_post_init_user(void) {
 }
 bool process_record_user(uint16_t keycode, keyrecord_t *record) {
-  // If console is enabled, it will print the matrix position and status of each key pressed
+    // If console is enabled, it will print the matrix position and status of each key pressed
-// #ifdef CONSOLE_ENABLE
+    // #ifdef CONSOLE_ENABLE
-//     uprintf("KL: kc: %u, col: %u, row: %u, pressed: %u\n", keycode, record->event.key.col, record->event.key.row, record->event.pressed);
+    //     uprintf("KL: kc: %u, col: %u, row: %u, pressed: %u\n", keycode, record->event.key.col, record->event.key.row, record->event.pressed);
-// #endif
+    // #endif
-  return true;
+    switch (keycode) {
    case MS_WH_DOWN:
        if (record->event.pressed) {
            SEND_STRING(SS_TAP(X_MS_WH_DOWN));
        }
        break;
    case MS_WH_UP:
        if (record->event.pressed) {
            SEND_STRING(SS_TAP(X_MS_WH_UP));
        }
        break;
    case MS_WH_LEFT:
        if (record->event.pressed) {
            SEND_STRING(SS_TAP(X_MS_WH_LEFT));
        }
        break;
    case MS_WH_RIGHT:
        if (record->event.pressed) {
            SEND_STRING(SS_TAP(X_MS_WH_RIGHT));
        }
        break;
    }
    return true;
 }
@@ -1,7 +1,6 @@
 # The nathanvercaemert ErgoDox EZ configuration
-Centered around the home row and the use of mouse keys, this configuration focuses
+Centered around the home row and the use of mouse keys, this configuration focuses on minimal finger movement. No key is more than one unit away from the home row.
 on minimal finger movement. No key is more than one unit away from a finger on the home row.
 ## Layers
@@ -20,7 +19,9 @@ on minimal finger movement. No key is more than one unit away from a finger on t
  navigation layers.
 * Navigation Layers
  * From the Mouse Layer, taps to the left home row navigate to scroll keys, arrow keys, and page keys.
 * Notes on Acceleration
  * Designated as "Slow" and "Fast" on the mouse layers (movement and scroll,) these keys can be held to allow for slow/precise or fast/efficient control.
 Here is the image of my keymap:
-![Default](https://i.imgur.com/kXywQIq.png)
+![Imgur Image](https://i.imgur.com/x6VgH9Z.png)
@@ -5,6 +5,5 @@ COMMAND_ENABLE = no
 RGBLIGHT_ENABLE = no
 TAP_DANCE_ENABLE=yes
-
+# Debugging
 #Beginning debugging process for LT() and permissive hold
 CONSOLE_ENABLE = yes
@@ -207,34 +207,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -30,4 +30,3 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
@@ -29,4 +29,3 @@ MIDI_ENABLE = no            # MIDI support
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
@@ -213,30 +213,3 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
@@ -33,6 +33,5 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
 CUSTOM_MATRIX = lite
@@ -17,4 +17,3 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
@@ -33,4 +33,3 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
@@ -18,7 +18,6 @@ UNICODEMAP_ENABLE = no      # Enable extended unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
 #VARIABLE_TRACE = no         # Use this to debug changes to variable values
 API_SYSEX_ENABLE = no       # This enables using the Quantum SYSEX API to send strings
 KEY_LOCK_ENABLE = no        # This enables key lock
@@ -33,4 +33,3 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
@@ -211,34 +211,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -30,6 +30,5 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs
 LAYOUTS = 65_ansi_blocker 65_iso_blocker
@@ -30,7 +30,6 @@ UNICODE_ENABLE = no          # Unicode
 BLUETOOTH_ENABLE = no        # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no            # Audio output on port C6
 FAUXCLICKY_ENABLE = no       # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no          # Enable support for HD44780 based LCDs
 LTO_ENABLE = yes
@@ -30,7 +30,6 @@ UNICODE_ENABLE = no          # Unicode
 BLUETOOTH_ENABLE = no        # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no            # Audio output on port C6
 FAUXCLICKY_ENABLE = no       # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no          # Enable support for HD44780 based LCDs
 LTO_ENABLE = yes
@@ -30,4 +30,3 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs
@@ -188,34 +188,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -30,4 +30,3 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs
@@ -30,6 +30,5 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 PS2_MOUSE_ENABLE = yes
 PS2_USE_USART = yes
@@ -165,30 +165,3 @@
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
@@ -29,6 +29,5 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
-LAYOUTS = ortho_4x16 
+LAYOUTS = ortho_4x16
@@ -31,7 +31,6 @@ RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
 MIDI_ENABLE = no            # MIDI support
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
 UNICODE_ENABLE = no         # Unicode
 UNICODEMAP_ENABLE = no      # ^^
@@ -31,4 +31,3 @@ UNICODE_ENABLE = yes        # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
@@ -29,5 +29,4 @@ MIDI_ENABLE = no            # MIDI support
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
 UNICODE_ENABLE = no        # Unicode
@@ -229,34 +229,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -30,6 +30,5 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = yes          # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
 LAYOUTS = planck_mit
@@ -33,5 +33,4 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH = AdafruitBLE       # Enable Bluetooth
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs
 ENCODER_ENABLE = no
@@ -29,4 +29,3 @@ MIDI_ENABLE = no            # MIDI support
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
@@ -24,7 +24,6 @@ CONSOLE_ENABLE = no
 DEBUG_ENABLE = no
 EXTRAKEY_ENABLE = no
 FAUXCLICKY_ENABLE = no
 HD44780_ENABLE = no
 LEADER_ENABLE = no
 MIDI_ENABLE = no
 MOUSEKEY_ENABLE = yes
@@ -29,7 +29,6 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
 LTO_ENABLE = no             # Use link time optimization
 RGB_MATRIX_ENABLE = WS2812  # Enable keyboard RGB backlight functionality with ws2812 driver
 RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
@@ -218,34 +218,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -30,4 +30,3 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
@@ -29,4 +29,3 @@ MIDI_ENABLE = no            # MIDI support
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
@@ -218,34 +218,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -19,5 +19,4 @@ MIDI_ENABLE = no            # MIDI support
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
 LAYOUTS = ortho_4x12
@@ -215,34 +215,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -30,6 +30,5 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 NO_USB_STARTUP_CHECK = yes  # Disable initialization only when usb is plugged in
 BLUETOOTH = RN42
@@ -229,34 +229,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
 /* Bootmagic Lite key configuration */
 // #define BOOTMAGIC_LITE_ROW 0
 // #define BOOTMAGIC_LITE_COLUMN 0
@@ -30,6 +30,5 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = yes          # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
 LAYOUTS = planck_mit
@@ -216,30 +216,3 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
@@ -30,6 +30,5 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
 ENCODER_ENABLE = yes
 RGB_MATRIX_ENABLE = WS2812
@@ -192,31 +192,3 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
 //#define MIDI_TONE_KEYCODE_OCTAVES 1
 /*
 * HD44780 LCD Display Configuration
 */
 /*
 #define LCD_LINES           2     //< number of visible lines of the display
 #define LCD_DISP_LENGTH    16     //< visibles characters per line of the display
 #define LCD_IO_MODE      1            //< 0: memory mapped mode, 1: IO port mode
 #if LCD_IO_MODE
 #define LCD_PORT         PORTB        //< port for the LCD lines
 #define LCD_DATA0_PORT   LCD_PORT     //< port for 4bit data bit 0
 #define LCD_DATA1_PORT   LCD_PORT     //< port for 4bit data bit 1
 #define LCD_DATA2_PORT   LCD_PORT     //< port for 4bit data bit 2
 #define LCD_DATA3_PORT   LCD_PORT     //< port for 4bit data bit 3
 #define LCD_DATA0_PIN    4            //< pin for 4bit data bit 0
 #define LCD_DATA1_PIN    5            //< pin for 4bit data bit 1
 #define LCD_DATA2_PIN    6            //< pin for 4bit data bit 2
 #define LCD_DATA3_PIN    7            //< pin for 4bit data bit 3
 #define LCD_RS_PORT      LCD_PORT     //< port for RS line
 #define LCD_RS_PIN       3            //< pin  for RS line
 #define LCD_RW_PORT      LCD_PORT     //< port for RW line
 #define LCD_RW_PIN       2            //< pin  for RW line
 #define LCD_E_PORT       LCD_PORT     //< port for Enable line
 #define LCD_E_PIN        1            //< pin  for Enable line
 #endif
 */
@@ -30,4 +30,3 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
@@ -29,5 +29,4 @@ UNICODE_ENABLE = no         # Unicode
 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
 AUDIO_ENABLE = no           # Audio output on port C6
 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
 HD44780_ENABLE = no         # Enable support for HD44780 based LCDs
 RGB_MATRIX_ENABLE = WS2812
Author	SHA1	Message	Date
Frans de Jonge	2b9f200a2a	[fix] dfu-programmer <0.7 doesn't support --force flag (#10292 ) Fixes <https://github.com/qmk/qmk_firmware/issues/10286>.	2020-09-13 02:17:47 +01:00
Darren Meehan	9e99a9b98c	Remove use of sudo in lily58 make docs (#10301 )	2020-09-12 20:40:31 +01:00
binepad	e4d46a1c00	[Keyboard] add binepad/bn003 (#10276 ) * ADD BINEPAD/BN003 * Update keyboards/binepad/bn003/config.h * Update keyboards/binepad/bn003/config.h * Update keyboards/binepad/bn003/rules.mk * Update keyboards/binepad/bn003/keymaps/via/keymap.c * Update readme.md added macro pad info * Update keyboards/binepad/bn003/readme.md * Update keyboards/binepad/bn003/bn003.c * Update keyboards/binepad/bn003/config.h * Update keyboards/binepad/bn003/config.h * Update keyboards/binepad/bn003/info.json * Update keyboards/binepad/bn003/rules.mk * Update keyboards/binepad/bn003/rules.mk * Update keyboards/binepad/bn003/rules.mk * Update bn003.c * Update keyboards/binepad/bn003/readme.md * Update keyboards/binepad/bn003/rules.mk * Update keyboards/binepad/bn003/config.h * Update keyboards/binepad/bn003/keymaps/via/rules.mk * Update keyboards/binepad/bn003/rules.mk	2020-09-12 03:11:30 -07:00
TheLibra23	7141de19d9	added VIA keymap for Keebio Viterbi (#10168 ) * added via keymap * replaced PRODUCT_ID 0x1157 with PRODUCT_ID 0x2157 replaced product id to distinguish rev2 from rev1. bakingpy gave me permission through discord chat. * Update keyboards/keebio/viterbi/keymaps/via/keymap.c * Update keyboards/keebio/viterbi/keymaps/via/rules.mk * made a simplier keymap.c for via folder Based from the default keymap, removed unnecessary codes.	2020-09-12 00:55:52 -07:00
Ben	c82865efab	Add VIA keymap for Plaid-Pad (#10057 ) * Add via keymap for Plaid-Pad - Add VIA support for the Plaid-Pad - Changes Vendor ID and Product ID (to follow VIA's guidelines) * Add extra encoder pads for rev1.1 * Change Product Id from pp to PP (hex value) * improved readme - detailed informations about rotary encoder, bootloader and firmware * Improved encoder informations in via keymap * Improved encoder infos and code in default keymap * add revision folder for rev1 and rev1.1 * change encoder assignment for defaul a via keymap * Update keyboards/keycapsss/plaid_pad/config.h * change revision number * Update keyboards/keycapsss/plaid_pad/rules.mk * Update keyboards/keycapsss/plaid_pad/rules.mk * Update keyboards/keycapsss/plaid_pad/rules.mk * Update keyboards/keycapsss/plaid_pad/rules.mk * Update keyboards/keycapsss/plaid_pad/readme.md * add license to header of .h and .c files * remove the list of alternate bootloaders - due to the pr checklist * Update keyboards/keycapsss/plaid_pad/rules.mk	2020-09-11 18:19:05 -07:00
Takeshi ISHII	d8d65bbf5f	[Docs] Update Japanese translation of feature_split_keyboard.md (#10283 ) Apply #10242 changes to ja/feature_split_keyboard.md	2020-09-11 13:10:30 -07:00
hidenori	58d7e9fa0e	[Keymap] Added ToyoshimaHidenori's keymap for Ergodash mini (#10228 ) * Add ToyoshimaHidenori's keymap * Remove some dead code and characters * Change the folder name from uppercase to lowercase * Remove uppercase folder	2020-09-11 13:06:38 -07:00
yulei	6de4a53c7c	[Keyboard] added SQUARE.X by iNETT Studio (#10066 ) * added SQUARE.X keyboard from the iNETT Studio * split to two sub directories * Apply suggestions from code review * Update keyboards/inett_studio/sqx/universal/universal.h * Apply suggestions from code review * update the matrix control keycodes settings * use the offical macro to the rgb matrix control * fixed led position issue * Apply suggestions from code review * removed the redundant #endif * update default keymap * Apply suggestions from code review * add license header	2020-09-11 02:28:23 -07:00
Alvaro Muente	3d3c2e1d3f	Add VIA support for JJ40 (#10263 ) * via support * Removing backspaces from jj40 keymap.c * Updating jj40/via/rules.mk	2020-09-11 00:03:49 -07:00
Callum Oakley	3d4f0028d6	[Keymap] major keymap overhaul (#10185 ) * experiment with userspace * reorganise * readme * missing oneshot shift from ignored keys * recombine hands in layout macro	2020-09-09 15:37:34 -07:00
Ryan	6e948feb6a	Use the force when flashing with dfu-programmer (#10070 )	2020-09-10 00:00:27 +10:00
Nick Christus	076b9d482f	[Keymap] Added nchristus userspace (#10261 ) * userspace: added nchristus * userspace: updates per PR review	2020-09-08 22:33:38 -07:00
Ramon ImbaoandRyan	08f6e64137	[Keyboard] Add Squishy65 keyboard (#10266 ) * Add Squishy65 keyboard * Edit info.json * Fix incorrect ISO layout * Add missing license in files * Update keyboards/ramonimbao/squishy65/config.h Co-authored-by: Ryan <[email protected]> * Update keyboards/ramonimbao/squishy65/keymaps/via/rules.mk Co-authored-by: Ryan <[email protected]> * Update keyboards/ramonimbao/squishy65/rules.mk Co-authored-by: Ryan <[email protected]> Co-authored-by: Ryan <[email protected]>	2020-09-08 22:32:47 -07:00
Jan Kolkmeier Drashna Jaelre James Young	4b9c3dc2e5	add keyboard: bemeier/bmek (revisited) (#10144 ) * bmek keyboard support * Update keyboards/bemeier/bmek/bmek.h Co-authored-by: Drashna Jaelre <[email protected]> * Update keyboards/bemeier/bmek/rules.mk Co-authored-by: Drashna Jaelre <[email protected]> * moved shutdown behavior to shutdown hook * removed dynamic macro option statement * Apply suggestions from code review Co-authored-by: James Young <[email protected]> * Apply suggestions from code review Co-authored-by: James Young <[email protected]> * change layout name in via * move/copy root rules to revs * Apply suggestions from code review Co-authored-by: Drashna Jaelre <[email protected]> * Apply suggestions from code review Co-authored-by: Drashna Jaelre <[email protected]> Co-authored-by: Drashna Jaelre <[email protected]> Co-authored-by: James Young <[email protected]>	2020-09-08 22:25:13 -07:00
boss566y Drashna Jaelre Ryan	ba3ec0f081	[Keymap] Romac Keymap with VIA and OLED Support (#10249 ) * Add Personal Keymap with VIA and OLED * Update keyboards/kingly_keys/romac/keymaps/boss566y/keymap.c Co-authored-by: Drashna Jaelre <[email protected]> * Update keyboards/kingly_keys/romac/keymaps/boss566y/keymap.c Co-authored-by: Drashna Jaelre <[email protected]> * Update keyboards/kingly_keys/romac/keymaps/boss566y/keymap.c Co-authored-by: Ryan <[email protected]> * Update keyboards/kingly_keys/romac/keymaps/boss566y/keymap.c Co-authored-by: Ryan <[email protected]> * Update keyboards/kingly_keys/romac/keymaps/boss566y/keymap.c Co-authored-by: Ryan <[email protected]> Co-authored-by: Drashna Jaelre <[email protected]> Co-authored-by: Ryan <[email protected]>	2020-09-08 21:24:23 -07:00
Nick Blyumberg	d3cea9ed93	[Keyboard] Added the proper RGB settings to allow via control (#10223 )	2020-09-08 21:10:30 -07:00
umi	5f00df0c4c	[Docs] Japanese translation of docs/reference_keymap_extras.md (#10138 ) * add reference_keymap_extras.md translation * update based on comment * update based on comment * update based on comment	2020-09-08 14:44:36 -07:00
MakotoKurauchi	cd73949682	updated readme.md of yushakobo/quick7 keyboard (#10243 ) * update "Hardware Availability" * add a section of "How to build" * update "Hardware Supported"	2020-09-07 23:20:16 -07:00
marksard	4e3a96ff3e	Update treadstone48/rev2 info.json (#10241 ) * Keyboard: add treeadstone48 * rename layout defines * Use of pragma once * move common include code * fixed info.json * change keymap layout from kc to normal * fix alpha revision keymap * fixed info.json * remove USE_Link_Time_Optimization * Updated treadstone48 info.json file * remove kc define * Nested layout macro 1/2 * Nested layout macro 2/2	2020-09-07 23:00:19 -07:00
marksard	ae7a076964	Update marksard/leftover30 info.json (#10240 ) * Keyboard: add treeadstone48 * rename layout defines * Use of pragma once * move common include code * fixed info.json * change keymap layout from kc to normal * fix alpha revision keymap * fixed info.json * remove USE_Link_Time_Optimization * Updated leftover30 info.json file	2020-09-07 22:37:15 -07:00
James Young	78d5224a1d	Remove HD44780 References, Part 3 (#10238 ) * remove HD44780_ENABLE rules: G-H * remove HD44780_ENABLE config: G-H	2020-09-07 22:28:18 -07:00
Takeshi ISHIIandRyan	088888937a	Replace figures in docs/feature_split_keyboard.md (#10242 ) * Replace figures in feature_split_keyboard.md * fig update * Update docs/feature_split_keyboard.md Co-authored-by: Ryan <[email protected]> Co-authored-by: Ryan <[email protected]>	2020-09-06 21:15:55 -07:00
Drashna JaelreandRyan	9fe3fc4c04	Add Bakeneko 65 (#10234 ) * Add Bakeneko 65 * Apply suggestions from code review Co-authored-by: Ryan <[email protected]> Co-authored-by: Ryan <[email protected]>	2020-09-06 21:03:58 -07:00
Vitja Makarov	6b1c58629f	[Keyboard] Fix adb_usb/aek layout keypad equal key (#10248 )	2020-09-06 21:03:16 -07:00
QMK Bot	3b1abe0dee	format code according to conventions [skip ci]	2020-09-07 03:50:14 +00:00
gitdrik	3b14c032e0	[Keymap] Added Finnish SFS 5966 keymap for planck. (#10200 ) * Added Finnish SFS 5966 keymap for planck. * Modified comments and added copyright header.	2020-09-06 20:49:20 -07:00
jackytrabbitandRyan	fb66f0a3fb	[Keyboard] Add VIA support for lazydesigners\bolt (#10218 ) * Add VIA support for lazydesigners\bolt Add VIA support for lazydesigners\bolt * Update keyboards/lazydesigners/bolt/via/rules.mk Co-authored-by: Ryan <[email protected]> Co-authored-by: Ryan <[email protected]>	2020-09-06 20:47:52 -07:00
Adam GwilliamandAdam Gwilliam	1d8b0ccc81	[Keyboard] add via support for boardsource/4x12 (#10220 ) Co-authored-by: Adam Gwilliam <[email protected]>	2020-09-06 18:10:18 -07:00
nathanvercaemertandNathan Vercaemert	92e5361fc5	[Keymap] Personal Keymap (nathanvercaemert) Update (#10107 ) * updates to incorporate combined mouse key acceleration functionality * tab switching in chrome works, updated readme * updated keymap image * updated keymap image Co-authored-by: Nathan Vercaemert <[email protected]>	2020-09-06 17:55:39 -07:00
moyi4681 Drashna Jaelre Ryan	8ea8a80c5b	[Keyboard] add Maja soldered keyboard (#10152 ) * add maja_soldered keyboard add maja_soldered keyboard * Update info.json * update keymap * Update keyboards/kbdfans/maja_soldered/config.h Co-authored-by: Drashna Jaelre <[email protected]> * Update keymap.c * Update keyboards/kbdfans/maja_soldered/rules.mk Co-authored-by: Ryan <[email protected]> * Update keyboards/kbdfans/maja_soldered/rules.mk Co-authored-by: Ryan <[email protected]> * Update keymap.c * Update keymap.c * Update keymap.c Co-authored-by: Drashna Jaelre <[email protected]> Co-authored-by: Ryan <[email protected]>	2020-09-06 17:55:06 -07:00
Alvaro MuenteandAlvaro	788cbcf828	[Keyboard] Update JJ40 VID and PID (#10215 ) Co-authored-by: Alvaro <[email protected]>	2020-09-06 17:52:57 -07:00
Koichi KatanoandRyan	28e10eedda	Apply suggestions from code review Co-authored-by: Ryan <[email protected]>	2020-09-07 09:33:12 +09:00
stanrc85	6c3e404839	[Keymap] Add indicator light bootup fanfare (#10158 ) * Add indicator light bootup fanfare * move fanfare code to new file * fanfare code in new file and remove unused boards * new startup fanfare code * add lock/unlock indicator animation * input key presses before changing lights * remove old code	2020-09-06 15:04:29 -07:00
Koichi Katano	461153150b	Add Bakeneko 65	2020-09-04 02:02:40 +09:00